SunSetter Motorized PRO Guide
RETRACTABLE AWNINGS
For Technical Support visit us at www.sunseer.com/ownerscorner
or Call Toll Free 800-670-7071 • Fax 877-224-4944
©SunSeer Products, a Massachuses Limited Partnership, 184 Charles Street, Malden, MA 02148
Motorized and Motorized PRO Awning
* Helpers needed *
Tools needed:
1.
2.
Note: For Awnings that
Aluminum Hood installed,
on the same side as the
Motor, remove the Hood
End Plate. See Figure 1.
3.
Figure 2
4.
This is necessary to keep the Roller Bar
from coming out of the Roller Bracket while the
Motor is unbolted from the other side.
See Figure 2.
Note: The Roller Bar can be removed from
between the Roller Brackets if more space is
needed to remove and replace the Motor. Be
careful to not lose the Gray Bushing on the Pin
at the end of the Roller Bar. The Helper(s) must
hold and stabilize the Roller Bar with care.
5.
Mark the
threaded holes in the Roller
Bracket that the bolts are
removed from. See Figure 3.
6.
Note at Step 4
7.
Figure 3
8.
aligning the cream colored slots
Figure 4
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN PERSONAL INJURY!! PLEASE
READ THESE INSTRUCTIONS IN ITS ENTIRETY BEFORE ATTEMPTING TO COMPLETE THIS PROCESS.
PLEASE NOTE THAT LEFT AND RIGHT REFERENCES ARE AS YOU ARE FACING THE HOUSE.
Figure 1
Figure 2
Figure 3
Figure 4
Note: The correct slots in the Tube Driver and Crown Gear are
marked with cream paint. As you insert the Motor, align this
cream colored slot with the Fabric Slot in the Roller Bar.
Tube Driver
Crown Gear
2
13.
14.
15.
16.
17.
Appendix A
18.
19.
Appendix A
Page 4
Note: If the old Motor needs to be returned to
the replacement Motor.
Note: The threaded holes on the replacement
Motor Plate are marked to indicate the holes to
use during reassembly. Align these holes with
the holes noted or marked on the Roller Bracket,
in Step 5.
9.
Note: Ensure the Gray Bushing is on the Round
Pin of the End Cap before sliding it into the
Roller Bracket (on the end opposite the Motor).
Ensure the End Cap
of the Roller Bar is in
contact with the Roller
Bracket on the end
opposite the Motor.
See Figure 5.
10.Step 7
11.
Figure 3
Note: Be very careful not to cross-thread the
Roller Bracket.
12.
Figure 6
Note:
For LEFT side Motor, the Override Crank
should be facing toward the Front of the
Awning and the Motor Cord should be facing
up. See Figure 7.
For RIGHT side Motor, the Override Crank
should be facing toward the Front of the
Awning and the Motor Cord should be facing
toward the ground. See Figure 8.
Figure 5
Round
Pin on
End Cap
End Cap on
Roller Bar
Programming
Appendix A
Tools needed:
WARNING: THIS PROCEDURE MUST BE FOLLOWED THOROUGHLY AND COMPLETELY.
Note
CLOSEOPEN
Note
right
my
CLOSE
CLOSE
myOPEN
my
CLOSEOPEN
myCLOSE
my
Noteadjust
CLOSE
OPEN
my
CLOSE
OPEN
my
Channel
Indicator
Lights
Channel
Selector
Button
4
Add a Wireless Wind Sensor
Figure 1
Figure 2
Figure 3
Figure 3
The LED on the Sensor Body will blink.
Step 3
Note: The Awning Motor will not accept a command
Wireless Wind Sensor has retracted the Awning.
Step 6
To shake the Front Bar,
the Bar to drop freely. Repeat quickly.
Steps 1 to 6
NEW SET OF BATTERIES
800-670-7071
WARNING: YOU MUST BE CERTAIN THAT THE WIRELESS
WIND SENSOR IS INSTALLED, PROGRAMMED AND
OPERATING PROPERLY.
FAILURE TO DO SO MAY RESULT IN THE WIRELESS WIND
SENSOR NOT BEING ABLE TO CLOSE YOUR AWNING
DURING WINDY CONDITIONS, WHICH COULD CAUSE
DAMAGE AND PERSONAL INJURY. IF THE MOTOR
DIRECTION IS REVERSED THE SENSOR WILL EXTEND
(OPEN) THE AWNING IN WINDY CONDITIONS, INSTEAD
OF CLOSING IT.
Add a Wireless Wall Switch
Figure 1
Figure 2
Figure 1
Rear
Programming
recessed
inside this
small opening
Remote Transmitter
Figure 2
Channel
Indicator
Lights
Channel
Selector
Programming
recessed inside
this small
opening
Multi-Channel Wall Switch
Figure 2
Figure 3
THEN
FIRST
Figure 1
LEFT
Lateral_SuneaMotor_Repl-v2
January12,2015
This manual suits for next models
1
Table of contents
Other SunSetter Accessories manuals
SunSetter
SunSetter 900XT User manual
SunSetter
SunSetter 900XT User manual
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter VISTA Original instructions
SunSetter
SunSetter Platinum Plus Guide
SunSetter
SunSetter Gaviota Quick start guide
SunSetter
SunSetter OASIS Series User manual
SunSetter
SunSetter VISTA Quick start guide
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter EASYSHADE Use and care manual
SunSetter
SunSetter EASYSHADE Use and care manual
SunSetter
SunSetter EASYSHADE Guide
SunSetter
SunSetter EASYSHADE Use and care manual
SunSetter
SunSetter 900XT Use and care manual
SunSetter
SunSetter EASYSHADE Original instructions
SunSetter
SunSetter Oasis Guide
SunSetter
SunSetter Platinum Plus Series Original instructions
SunSetter
SunSetter 900XT User manual
SunSetter
SunSetter PRO Operating and safety instructions
SunSetter
SunSetter Oasis Guide
Popular Accessories manuals by other brands
Veeder-Root
Veeder-Root TLS installation instructions
RS Biotech
RS Biotech Galaxy S+ user manual
LEGRAND
LEGRAND Tynetec Aidcall quick start guide
Screen Innovations
Screen Innovations Solo Pro installation instructions
aci
aci Room Series Installation & operation instructions
CALECTRO
CALECTRO Uniguard Superflow UG3-A-SENSE Installation instruction
