superbrightleds DDAL-SW3B Series User manual

Field-Selectable Wattage and CCT LED
Dusk-to-Dawn Area Light
User Manual
Important: Read all instructions prior to installation. DDAL-SW3Bx
Parts Included
Specications
Photocell Operation
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
- area light
- pole mount bracket
- access plate (for wall installation)
- hardware kit
DDAL-SW3B60
Model DDAL-SW3Bx
Environmental Rating IP65
Operating Temperature -40°–113° F (-40°–45° C)
• Product should be installed by a certied electrician in
accordance with applicable national, state, and local
building and electrical codes.
• To reduce the risk of electric shock, ensure that the main
power source and circuit breakers are switched o󰀨 before
performing any installation or wiring procedures.
• Avoid looking directly into the lamp when illuminated.
• Ensure all mounts are securely attached and will support
the weight of the xture. Failure to properly support
the xture may result in damage or injury, for which the
manufacturer does not assume responsibility.
Safety and Notes
CCT and Wattage Selection
Included photocell sensor switches light on when ambient
light goes below 40 lx, and o󰀨 when ambient light goes back
above 125 lx.
Check product label for specific electrical
specifications related to installation.
Improper installation will void warranty.
CCT and wattage are selected using the DIP
switch on the front of the light.
Rev Date: V1 11/01/2021
10#
.30in
7.62mm
2.65in
67.31mm
2.46in
62.43mm
2.17in
55.12mm
ON
Wattage Selection
Photocell
CCT Selection
100% 80%
OFF ON
5000K 4000K 3000K
60%
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5

WIFI-CON
User Manual
Important: Read all instructions prior to installation.
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Pole Mount Installation
1. Remove supply power.
2. Make all electrical connections.
3. Loosely attach pole mount bracket to light.
4. Slide light over pole (max diameter 1.75” OD) and tighten mount bracket.
Note: Overtightening bracket may result in damage to pole or bracket.
5. Restore supply power.
6. Remove cap and adjust wattage and CCT to desired value. Replace cap to prevent damage to switch.
Wall Mount Installation
1. Remove supply power.
2. Measure mounting ange and drill three pilot holes.
3. Partially thread the bottom two lag screws in place.
4. Place light over to lower lag screws and install third lag screw, then tighten all lag screws.
5. Make all electrical connections. Wire should pass through rear or lower access plate knockout
using conduit.
6. Attach access plate to light.
7. Restore supply power.
8. Remove cap and adjust wattage and CCT to desired value. Replace cap to prevent damage to switch.
Field-Selectable Wattage and CCT LED
Dusk-to-Dawn Area Light
DDAL-SW3Bx
Rev Date: V1 11/01/2021
10#
.30in
7.62mm
2.65in
67.31mm
2.46in
62.43mm
2.17in
55.12mm
ON
Wattage Selection
Photocell
CCT Selection
100% 80%
OFF ON
5000K 4000K 3000K
60%
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
10#
.30in
7.62mm
2.65in
67.31mm
2.46in
62.43mm
2.17in
55.12mm
ON
Wattage Selection
Photocell
CCT Selection
100% 80%
OFF ON
5000K 4000K 3000K
60%
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5
ON
1 2 4 5