superbrightleds PLLD4 Series User manual

LED Parking Lot/Area Light
Important: Read all instructions prior to installation. PLLD4 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V3 03/30/2022
User Manual
5yr
Mounting Options
Safety and Notes
Environmental Specications
Operating Temperature -31°–122° F (-35°–50° C)
IP Rating IP65
Wall/Trunnion Mount (PLLD4-WM)
Slip-Fitter (PLLD4-SF)
Flood Mount (PLLD4-FB1, PLLD4-FB2)
Adjustable Pole Mount (PLLD4-APM)
• Product should be installed and serviced by a certied electrician
in accordance with applicable national, state, and local building
and electrical codes.
• To reduce the risk of electric shock, ensure that the main power
source and circuit breakers are switched o󰀨 before performing
any installation or wiring procedures.
• Avoid looking directly into lamp when illuminated.
• Ensure all mounts are securely attached and will support the
weight of the xture. Failure to properly support xture may
result in damage or injury, for which the manufacturer does not
assume responsibility.
Specications
PLLD4-50K300W-BLT3BR1with PLLD4-SF
Check product label for specific electrical
specifications related to installation.
Improper installation will void warranty.
Wiring Diagram
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Dim (+)
Dim (-)
Purple
+ +
- -
Gray / Pink
Green
Line
Neutral
Ground
Black
L L
N N
GND GND
White
Dim (+)
Dim (-)
Purple
+ +
- -
Gray / Pink
Green
120–277 / 277–480 VAC Input 1–10 V / 0–10 V Dimming

LED Parking Lot/Area Light
Important: Read all instructions prior to installation. PLLD4 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V3 03/30/2022
User Manual
5yr
Trunnion Wall/Surface Mount (PLLD4-WM) Installation
Slip-Fitter (PLLD4-SF) Installation
1. Use trunnion mount as a template to make mounting
holes on wall/surface and install hardware.
2.Run wiring through the ange then attach the light
to the bracket.
3.Mount bracket to surface.
4.With supply power o󰀨, connect wiring.
5.Once installation is complete, the position locking
bolts can be removed and the center trunnion bolts
can be loosened to adjust the mounting angle of the
light. Reinstall the position locking bolts and retighten
center bolt when the desired angle is achieved. 180°
3.96 in
[100.5mm]
1. Disassemble mount and run wiring through it.
2. Reassemble mount.
3. Attach mount to light.
4. With supply power o󰀨, connect wiring.
5. Slide mount over pole/post and secure in place.
The maximum pole/post diameter is 2.375 in.
6. Rotate light to desired angle and tighten adjustment
screw.
90°

LED Parking Lot/Area Light
Important: Read all instructions prior to installation. PLLD4 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V3 03/30/2022
User Manual
5yr
Adjustable Pole Mount (PLLD4-APM) Installation
1. Remove side access plate cover on mount.
2.Run wiring through the ange that attaches
to the light.
3.Attach mount to light.
4.Make appropriate mounting and wiring holes
in pole/post and attach mount to pole/post.
5.With supply power o󰀨, use side access to
connect wiring.
6.Loosen adjustment bolt to adjust angle.
Rotate light to desired angle and tighten
adjustment screw.
7. Re-install side access plate cover.
Flood Mount (PLLD4-FB1, PLLD4-FB2) Installation
1. Use U-bracket mount as a template to make mounting holes
on wall/surface and install hardware.
2.Attach the light to the bracket
3.Mount light to surface.
4.With supply power o󰀨, connect wiring.
5.Once installation is complete, the position locking bolts can
be removed and the center trunnion bolts can be loosened
to adjust the mounting angle of the light. Reinstall the position
locking bolts and retighten center bolt when the desired
angle is achieved.
Note: PLLD4-FB1 is compatible with 100–150 W models.
PLLD4-FB2 is compatible with 240–450 W models.

LED Parking Lot/Area Light
Important: Read all instructions prior to installation. PLLD4 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V3 03/30/2022
User Manual
5yr
Photocell Installation
1. Remove photocell access plate.
Note: 100 W models will require drilling.
2.Attach Photocell receptacle socket.
3.With supply power o󰀨, make all wiring connections according to the diagram.
4.Photocell plugs in and twists to lock.
Note: JL-205C photocell is meant for operation with 120–277 VAC.
JL-207F photocell is meant for operation with 480 VAC.
Photocell
Line
Neutral
Ground
Purple (Dim +)
Green
White
White Red Black
Black
N/C
N/C Gray (Dim -)
Light