superbrightleds XS-RG User manual

LED Exit Signs
User Manual
XS-RG and XSC-RG
Model XS-RG XSC-RG
Power Consumption 1 W 2 W
Input Voltage 120/277 VAC 120–277 VAC
Operating Temperature 32°–104° F (0°–40° C)
Specications
Dual-Sided Operation / Changing Lettering Color
XS-RG (in green conguration)
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
1. Carefully remove the “EXIT” panel using a at-head
screwdriver to release tabs.
2. To swap color, remove the di󰀨user and swap with the other
included one, then switch the LED color using the internal
selection switch.
3. For dual-sided use, remove the blank rear panel using
a at-head screwdriver to release tabs and replace with
additional exit panel.
¹
¹Limited 2-year warranty on battery.
Rev Date: V1 09/16/2022
Important: Read all instructions prior to installation. SAVE THESE INSTRUCTIONS.
Important Safeguards
Read and follow all safety instructions. When using electrical
equipment, basic safety precautions should always be followed
including the following:
• This product should be installed and serviced by a certied
electrician in accordance with applicable national, state, and
local building and electrical codes.
• Light must be maintained, tested, and serviced in
accordance with all applicable National Fire Protection
Association (NFPA) and local codes.
• To reduce the risk of electric shock, ensure that the main
power source and circuit breakers are switched o󰀨 before
performing any installation or wiring procedures.
• Ensure xture is securely mounted and mount will support
weight of the xture. Failure to properly support xture may
result in damage or injury, for which the manufacturer does
not assume responsibility.
• Equipment should be mounted in locations and at heights
where it will not be subjected to tampering by unauthorized
personnel.
• Indoor use only—do not use outdoors.
• Do not mount near gas or electric heaters or any other
radiant heat sources.
• Use caution when handling or servicing the battery pack.
• For conduit wiring installation, use exible conduit only
• The use of accessory equipment not recommended by the
manufacturer may cause an unsafe condition.
• Do not use this equipment for anything other than its
intended use and do not use with accessories not included
with this equipment.
• Do not repair or modify arbitrarily. Do not replace any part of
the light including LED board and transformer/driver without
consulting the manufacturer or authorized distributors.
• Battery in this unit may not be fully charged when
purchased. After electricity is connected to the unit, let the
battery charge for at least 24 hours before testing.
• On XS-RG model, never connect red and black wires at the
same time. Only one should be connected to the appropriate
voltage at any time.
Mounting plate
Canopy
Hole plug
Hole plug
Mounting
plate
Canopy
Junction box
(not included)
Junction box
(not included)
swap diffuser panel
color selection switch
Mounting plate
Canopy
Hole plug
Hole plug
Mounting
plate
Canopy
Junction box
(not included)
Junction box
(not included)
swap diffuser panel
color selection switch
Wiring Diagram
White
Red
Neutral
Line (120–277 VAC)
XSC-RG
White
Red
Black
Neutral
Line (277 VAC)
Line (120 VAC)
XS-RG

1. Disconnect supply power.
2. Carefully remove the “EXIT” panel using a at-head screwdriver to release tabs.
3. Swap color and install additional exit panel for dual sided use if desired.
4. Run wiring through mounting bracket, then attach mounting bracket to light.
5. Install mounting bracket on junction box and connect supply wiring. On XS-RG model, cap unused wire.
6. Mount light to mounting bracket.
7. Connect battery.
8. Reinstall “EXIT” panel. Install/remove directional arrow covers as needed.
9. On XSC-RG, aim emergency light heads as needed.
10. Restore supply power and allow battery pack to charge for at least 24 hours before initial test.
11. After 24-hour period, press test button to make certain light is functioning as intended.
Ceiling or Side Mount Installation
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
LED Exit Sign
XS-RG and XSC-RG
User Manual
Rev Date: V1 09/16/2022
Important: Read all instructions prior to installation. SAVE THESE INSTRUCTIONS.
Mounting plate
Canopy
Hole plug
Hole plug
Mounting
plate
Canopy
Junction box
(not included)
Junction box
(not included)
swap diffuser panel
color selection switch
¹
¹Limited 2-year warranty on battery.
side mounting is not
possible on XSC-RG

1. Disconnect supply power.
2. Carefully remove the “EXIT” panel using a at-head screwdriver to release tabs.
3. Swap color and install additional exit panel for dual sided use if desired.
4. Make holes in rear panel for wiring and mounting.
5. Connect supply wiring. On XS-RG model, cap unused wire.
6. Attach light to wall.
7. Connect battery.
8. Reinstall “EXIT” panel. Install/remove directional arrow covers as needed.
9. On XSC-RG, aim emergency light heads as needed.
10. Restore supply power and allow battery pack to charge for at least 24 hours before initial test.
11. After 24-hour period, press test button to make certain light is functioning as intended.
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
LED Exit Sign
XS-RG and XSC-RG
Rear Wall Installation
¹Limited 2-year warranty on battery.
User Manual
Important: Read all instructions prior to installation. SAVE THESE INSTRUCTIONS.
Keyhole knockouts
Center knockout
Junction box
(not included)
RED-LIVE(HOT)
WHITE-NEUTRAL(COMMON)
POWER SUPPLY
Battery
LED MODULE / CONTROL BOARD
WHITE (NEUTRAL)
RED (LIVE)
220-277Vac (nominal)
LED indicator Test switch
Slide switch
(RED/GREEN)
Rev Date: V1 09/16/2022
¹