Swann One Outdoor Siren User manual

Overview
Thank you for choosing the SwannOne™ Outdoor Siren -
the ideal addition to your SwannOne Smart Home system.
Please take a moment to familiarize yourself with key parts
of the outdoor siren.
QSGOS130415E
© Swann Communications 2015
EN
Quick Start Guide
READ ME
FIRST
Outdoor
Siren www.swannone.com
Cover
Tamper Switch
Detects when
the siren is
removed from
the wall or its
cover opened,
causing the siren
to sound
Locking Screw
Secures the cover
to the siren
Connect
Button
Mounting
Holes x 4
ON/OFF
Switch
Strobe LED
x 3
Front
Internal Components
Battery Compartment
Requires 4 x "D"
alkaline batteries
(included)
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1)This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Strobe
Battery Safety Information
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO
THE INSTRUCTIONS.
Disposal and Recycling Information
Correct Disposal of this product. This marking indicated that this
product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibly
to promote the sustainable reuse of material resources. To return your
used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environment safe recycling.
Check the status of the siren's batteries via the SwannOne app.
When necessary, replace with fresh alkaline batteries by matching the
polarity (+ and -) markings shown inside the battery compartment.

Warranty
Your SwannOne product is backed by a full 12 month
guarantee from the date of purchase. In the unlikely event
of anything going wrong, you can have confidence that
your purchase is protected. Refer to swannone.com for
terms and conditions.
Prepare Siren Connect Siren Mount Siren
Test Siren
Loosen the locking screw located at the bottom of the
siren and then remove the cover.
Get more information regarding the setup and use of your
product on the web at swannone.com, or contact our
multi-lingual support team anytime via:
CAUTION
The siren is extremely loud! When testing the siren, protect
your hearing by wearing earplugs, or stand at least 3 meters
away from the siren.
123
4
ASign in to your SwannOne account at
home.swannone.com.
BFrom your web account dashboard, go to
My Devices > Sirens and add a device. When the
Setup page appears, put your Smart Hub in pairing
mode by selecting the option to learn devices.
CSlide the siren's ON/OFF switch to the ON position.
DPress and hold the siren's Connect button until the
right-most strobe LED located below the battery
compartment blinks once.
When pairing is complete, the strobe LED will blink
twice. Check the Setup page to confirm the siren
was paired successfully and then finish the setup by
following the on-screen instructions.
ATurn off the siren by sliding the ON/OFF switch to
OFF. This prevents the siren from sounding if you
inadvertently activate the tamper switch.
BChoose a prominent place on an external wall, high up
as possible to mount the siren, so it is out of easy reach
of any potential vandal.
For optimal performance and longevity, install the siren under
eaves, verandahs or other sheltered locations.
CScrew the siren onto the wall using the included wall
plugs and screws through the four mounting holes on
the siren base.
DTurn on the siren by sliding the ON/OFF switch to ON.
The siren's tamper protection function is only enabled 5
minutes after the siren is powered up, enough time for you to
replace the cover properly without triggering the tamper alarm.
ERe-attach the cover and tighten the locking screw to
secure the cover to the siren.
• Arm your SwannOne system in Away mode using
your key fob and then trigger an alarm by walking
past your motion sensor. The siren goes off and you
will also receive a notification on your smartphone.
By default, the siren will sound for 3 minutes.
• To stop the siren manually, press the Home mode
button on your key fob.
Connect Button
ON/OFF Switch
Tamper Swit c h
Battery Compartment
If the siren did not connect as expected, try switching the siren
off, then on again after 30 seconds, and repeat step 2D.
Need Help?
[email protected]
USA & Canada 1800 627 2799
UK & Europe 0808 168 9031
Australia 1800 788 210
New Zealand 0800 479 266