Swegon IQlogic+ TBIQ-3-2-aa GOLD User manual

GB.TBIQ3.130915
Swegon reserves the right to alter specifications. www.swegon.com 1
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
P1
COM POWER
IQlogic+
1234 5678 9101112
-+-+ -++--S-S
C
13
NO
14
C
15
NO
16
+
17
-
18
+
19
-
20
G
21
G0
22
Com 1Heat/Cool Com 2
Installation, IQlogic+, modules TBIQ-3-1-aa and TBIQ-3-2-aa
GOLD
1. General
The IQlogic+is used for extra functions for which the
inputs and outputs are not included as standard in the air
handling unit’s control unit.
2. Installation
Install the IQlogic+at an appropriate place, for example at
an unoccupied spot on a DIN rail inside the air handling
unit’s electrical equipment cubicle .
Connect the communication cable, supplied with the unit,
to one of the connections on the module. It is not impor-
tant which connection is used. The reason why there are
two connections is to make it possible to connect several
IQlogic+.
Connect the other end of the communication cable to one
of the connections of the control unit, marked COM (the
exact connection is specified under the relevant function).
Function selector switch
0 ReCO2, TBIQ-3-1
1 Coil heat exchangers, TBIQ-3-1
2 Plate heat exchanger, TBIQ-3-1
3 External supervision, TBIQ-3-2
4 HumidificationPlate heat exchanger, TBIQ-3-1
5 AQUA Link (see separate instructions), TBIQ-3-1
6 External supervision, TBIQ-3-2
7 All Year Comfort (see separate instructions), TBIQ-3-2
8 Booster unit, TBIQ-3-2
9 Preheating, TBIQ-3-2
A Xzone heating (see separate instr. TBLZ-1-50), TBIQ-3-2
B Xzone cooling (see separate instr. TBLZ-1-50), TBIQ-3-2
C Spare
D Spare
E Extra control sequence and Season Heating, TBIQ-3-2
F Spare
Function
selector
switch
3. Data
Connection port 2 x RJ 12 6/6
Supply voltage
(Via modular contact) 24V DC
Relay contacts 2 A/AC3
5 A/AC1
Ambient temp.
normal -40 °C - +55 °C, 10 - 95 % RH
Enclosure class IP 20 to EN 60529
CE-approved to EN 61000-6-2, EN 61000-6-3
A TBIQ-3-2 is shown.

GB.TBIQ3.130915
Swegon reserves the right to alter specifications.
2 www.swegon.com
28
30
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
P1
IQlogic+
COM POWER
1234 5678
-+-+ -S-S
C
9
NO
10
+
11
-
12
Com 1 Com 2
12 89
*
4. Function
4.1 ReCO2
The IQlogic+is used for the ReCO2 function (function selec-
tor switch set to position 0).
The function can be activated in the hand-held micro ter-
minal of the GOLD unit or via a communication interface.
The module controls the outdoor air dampers.
Connect the cable for BUS communication to one of the
ports in the air handling unit’s IQlogic control unit marked
COM6-11.
* The conductors for supplying 24 V AC power can be connected to
Terminals 28 (P) and 30 (G0) on the air handling unit control unit.
Applicable to size 100/120 GOLD units only:
If the total load on Terminals 28-30 is higher than 16 VA, use Terminals
201 (G) and 202 (G0). Terminals 201-202 can be loaded with a total of
max, 48 VA.
Outdoor air damper/External damper
GOLD Control unit

GB.TBIQ3.130915
Swegon reserves the right to alter specifications. www.swegon.com 3
201
202
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
P1
IQlogic+
COM POWER
1234 5678
-+-+ -S-S
C
9
NO
10
+
11
-
12
Com 1 Com 2
203
204
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
P1
IQlogic+
COM POWER
1234 5678
-+-+ -S-S
C
9
NO
10
+
11
-
12
Com 1Com 2
4.2 Coil heat exchangers
The IQlogic+is used for the coil heat exchanger function.
One IQlogic+module is installed, as standard, in all GOLD
CX air handling units. The IQlogic+module’s function
selector switch is set to position 1.
The module controls the circulation pump of the pipework
package and the valve actuator on the coil heat exchang-
er.
A limiting sensor is connected to the module. Readings
from the temperature sensor (strap-on type) prevent the
water circulating through the extract air coil from reaching
such low temperatures that freezing is likely.
The cable for BUS communication is connected to one
of the ports in the air handling unit’s IQlogic control unit
marked COM6-11.
Valve
actuator
Temp.
sensor*
Green
Brown
Yellow
White Brown
White
4.3 Plate heat exchanger
IQlogic+ is used for the plate heat exchanger function.
One IQlogic+module is installed, as standard, in all GOLD
PX air handling units. The IQlogic+module’s function selec-
tor switch is set to position 2.
The module controls the by-pass and shut-off damper
actuators on the plate heat exchanger.
Two limiting sensors are connected to the module. Read-
ings from the temperature sensor (strap-on type) prevent
the foil, in the extract air passages of the heat exchanger
cube, from reaching such low temperatures that freezing
is likely.
The cable for BUS communication is connected to one
of the ports in the air handling unit’s IQlogic control unit
marked COM6-11.
Damper
actuator Temp.
sensor 1*
Black
Red
Grey
Pink Brown
White
Temp.
sensor 2*
Brown
White
* Digital temperature sensors require correct polarity. Be careful when
you wire the conductors.
* Digital temperature sensors require correct polarity. Be careful when
you wire the conductors.
Circulation pump
Pump alarm

GB.TBIQ3.130915
Swegon reserves the right to alter specifications.
4 www.swegon.com
4.4 External supervision
The IQlogic+is used for external supervision by means of
analogue and digital signals (function selector switch set
to position 3 and/or 6) in the applications where com-
munication with the air handling unit cannot be used. the
module can for example be used if the air handling unit
will be controlled/supervised via microprocessor substation
or a PLC system. the function can be activated in the air
handling unit’s hand-held micro terminal or via a commu-
nication interface.
Connect the cable for BUS communication to one of the
ports in the air handling unit’s IQlogic control unit marked
COM1-3.
Relay 1 Closes between Terminals 13 and 14 when
the control system, in the hand terminal,
indicates Selected function*, active.
Factory preset function: Heating load for
heat exchanger.
Relay2 Closes between Terminals 15 and 16 when
the control system, in the hand terminal,
indicates Selected function*, active. Fac-
tory preset function: Cooling demand.
* Two of the functions below may be indicated:
All GOLD
AHU in operation/AHU operating in automatic
mode/AHU operating in manual mode/AHU
operating in low speed mode/AHU operating in high
speed mode/A alarm/B alarm/Damper relay/
Heat exchanger/Heat exchanger, defrosting/Reheat/
Reheat capacity reduction/Heating Boost/Morning
Boost/Intermittent night operation/Airflow,
control to lower speed/Extra control sequence,
heating/Extra control sequence, cooling/
Cooling/Cooling BOOST/Summer night cooling
Digital In 1 Connect to Terminals 17 and 18.
The following functions can be selected in
the hand-held micro terminal:
- Alarm reset. Resets possible alarms on
closure.
- External stop of the AYC cooling water
flow regulation system. Blocks the cooling
water flow regulation and pump function
when the input is interrupted.
- External stop of the AYC heating water
flow regulation system. Blocks the heating
water flow regulation and pump function
when the input is interrupted.
Factory preset function: Alarm reset.
Digital In 2 Connect to Terminals 19 and 20.
The following functions can be selected in
the hand-held micro terminal:
- Alarm reset. Resets possible alarms on
closure.
- External stop of the AYC cooling water
flow regulation system. Blocks the cooling
water flow regulation and pump function
when the input is interrupted.
- External stop of the AYC heating water
flow regulation system. Blocks the heating
water flow regulation and pump function
when the input is interrupted.
Factory preset function: Alarm reset.
Digital sensor 1 Spare
Digital sensor 2 Spare
Analogue In 1 Connect to Terminals 5 (-) and 6 (+).
The following functions can be selected in the hand-held
micro terminal:
- Setpoint displacement of the temperature
- Forced supply airflow.
- Forced extract airflow.
Factory preset function: Forcing the supply
airflow.
Analogue In 2 Connect to Terminals 7 (-) and 8 (+).
The following selection can be made via
the hand terminal:
- Setpoint displacement of the temperature
- Forced supply airflow.
- Forced extract airflow.
Factory preset function: Forced extract
airflow.

GB.TBIQ3.130915
Swegon reserves the right to alter specifications. www.swegon.com 5
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
P1
IQlogic+
COM POWER
1234 5678
-+-+ -S-S
C
9
NO
10
+
11
-
12
Com 1 Com 2
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
P1
IQlogic+
COM POWER
1234 5678
-+-+ -S-S
C
9
NO
10
+
11
-
12
Com 1 Com 2
4.5 Humidification
Steam humidifier
The IQlogic+is used for the steam humidifier function
(function selector switch set to position 4).
Select Humidification in the air handling unit’s hand-held
micro terminal or via a communication interface.
The relay output is used for controlling the steam humidi-
fier, on/off.
Digital input can be used for external alarms. Select nor-
mally open or normally closed contact function in the AHU
hand-held micro terminal.
Use the analogue output for variably modulating 0 – 10 V
to the steam humidifier.
Connect the cable for BUS communication to one of the
ports in the air handling unit’s IQlogic control unit marked
COM1-3.
Steam humidifier (not Swegon)
Alarms**
0-10 V In
Start -
Stop*
+ -
Evaporative humidification
The IQlogic+is used for the evaporative humidification
function (function selector switch set to position 4).
Select Humidification in the air handling unit’s hand-held
micro terminal or via a communication interface.
The relay output is used for controlling the humidifier’s
solenoid valve or circulation pump, on/off.
Connect the cable for BUS communication to one of the
ports in the air handling unit’s IQlogic control unit marked
COM1-3.
Solenoid valve or circulation
pump, evaporative humidifier
(not Swegon)
* Normally-open contact starts the humidifier.
** Select the normally-open contact function in the AHU hand-held
micro terminal.
Supply volt-
age

GB.TBIQ3.130915
Swegon reserves the right to alter specifications.
6 www.swegon.com
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
P1
COM POWER
IQlogic+
1234 5678 9101112
-+-+ -++
--
S-S
C
13 NO 14 C 15 NO 16 +
17
-
18
+
19
-
20 G
21 G0 22
Com 1Heat/Cool Com 2
G0
G24 VAC
MM
01
02
Swegon
ASM115SF901
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
P1
IQlogic+
COM POWER
1234 5678
-+-+ -S-S
C
9
NO
10
+
11
-
12
Com 1 Com 2
4.6 AQUA Link
The IQlogic+is used for the AQUA Link function (function
selector switch set to position 5).
Select AQUA Link in the air handling unit’s hand-held
micro terminal or via a communication interface.
The relay output is used for controlling the circulation
pump.
The digital input can be used for external alarms. Select
normally open, normally closed or contactor function in
the AHU’s hand-held micro terminal or via a communica-
tion interface.
Connect the cable for BUS communication to one of the
ports in the air handling unit’s IQlogic control unit marked
COM1-3. Circulation pump
Pump alarm
Actuator for
BOOSTER
4.7 All Year Comfort
The IQlogic+is used for the All Year Comfort function
(function selector switch set to position 7).
See the Guide to the All Year Comfort Functions and
Installation of the TBLZ-2-59 control box.
Connect the cable for BUS communication to one of the
ports in the air handling unit’s IQlogic control unit marked
COM1-3.
4.8 Booster unit
The IQlogic+is used for the Booster unit function (function
selector switch set to position 8), where type BOOSTER
displacement units with damper motor are used. Relay 1
on the module is energised when the supply air tempera-
ture is higher than the room temperature, relay 2 operates
inversely compared to Relay 1, i.e. that when relay 1 is
energised Relay 2 is de-energised and vice versa.
Connect the cable for BUS communication to one of the
ports in the air handling unit’s IQlogic control unit marked
COM1-3.

GB.TBIQ3.130915
Swegon reserves the right to alter specifications. www.swegon.com 7
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
P1
COM POWER
IQlogic+
1234 5678 9101112
-+-+ -++
--
S-S
C
13
NO
14
C
15
NO
16
+
17
-
18
+
19
-
20
G
21
G0
22
Com 1Heat/Cool Com 2
4.9 Preheating
The IQlogic+is used for the preheating function (function
selector switch set to position 9).
The function can be activated in the hand-held micro ter-
minal of the GOLD unit or via a communication interface.
The module controls the air heater for water or the electric
air heater.
To wire the TBLA/TCLA air heater, water, for the
GOLD, or electric air heater of a type other than
Swegon standard
The valve actuator is fitted with a quick-fit connector on
the control cable.
Wire the circulation pump cable, if required, to the relay
output.
The anti-frost sensor (if required) for the water air heater is
equipped with RJ 45 connector.
Connect the cable for BUS communication to one of the
ports in the air handling unit’s IQlogic control unit marked
COM1-3.
Applicable to size 100/120 GOLD units only:
If the total load on Terminals 31-32 is higher
than 16 VA, use Terminals 201 (G) and 202 (G0).
Terminals 201-202 can be loaded with a total of
max, 48 VA.
* Digital temperature sensors require correct polar-
ity. Be careful when you wire the conductors.
Temp. sensor*
for preheating
Control of the
circulation pump
T1
GR
R1
RD
Jack for wall
mounting, 019611
32 (G0) IQlogic control unit
31 (G) IQlogic control unit
Blue
Orange
Black
Red
Green
Yellow
Brown
White alt.
grey
Brown
White
Resistor/air heater/air cooler type, 2.2 kΩ
Insertion-type/strap-
on sensor
Valve actuator
0-10 V DC output signal
0-10 V DC control signal
G0 24 V AC
G 24 V AC

GB.TBIQ3.130915
Swegon reserves the right to alter specifications.
8 www.swegon.com
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
P1
COM POWER
IQlogic+
1234 5678 9101112
-+-+ -++
--
S-S
C
13
NO
14
C
15
NO
16
+
17
-
18
+
19
-
20
G
21
G0
22
Com 1Heat/Cool Com 2
To wire a standard air heater for the GOLD, TBLE/
TCLE
The control cable of the standard, type TBLE/TCLE coils are
fitted with a quick-fit connector.
Connect the cable for BUS communication to one of the
ports in the air handling unit’s IQlogic control unit marked
COM1-3.
Temp. sensor,* for preheated air
Electric
air heater
Swegon
Standard
with 8-pin
control cable
R1
RD
T1
GR
Jack for wall
mounting, 019611
Applicable to size 100/120 GOLD units
only:
If the total load on Terminals 31-32 is
higher than 16 VA, use Terminals 201
(G) and 202 (G0). Terminals 201-202
can be loaded with a total of max, 48
VA.
* Digital temperature sensors require
correct polarity. Be careful when you
wire the conductors.
32 (G0) IQlogic control unit
31 (G) IQlogic control unit

GB.TBIQ3.130915
Swegon reserves the right to alter specifications. www.swegon.com 9
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
P1
COM POWER
IQlogic+
1234 5678 9101112
-+-+ -++--S-S
C
13
NO
14
C
15
NO
16
+
17
-
18
+
19
-
20
G
21
G0
22
Com 1Heat/Cool Com 2
4.10 Extra control sequence and Season
Heating
The IQlogic+is used for the extra control sequence and
Season Heating (function selector switch set to position E).
The function can be activated in the hand-held micro ter-
minal of the GOLD unit or via a communication interface.
The module controls the air heater for water or the electric
air heater.
To wire the TBLA/TCLA air heater, water, for the
GOLD, or electric air heater of a type other than
Swegon standard
The valve actuator is fitted with a quick-fit connector on
the control cable.
Wire the circulation pump cable, if required, to the relay
output.
The anti-frost sensor (if required) for the water air heater is
equipped with RJ 45 connector.
Connect the cable for BUS communication to one of the
ports in the air handling unit’s IQlogic control unit marked
COM1-3.
Applicable to size 100/120 GOLD units only:
If the total load on Terminals 31-32 is higher
than 16 VA, use Terminals 201 (G) and 202
(G0). Terminals 201-202 can be loaded with
a total of max, 48 VA.
Control of the
circulation pump
When the Season Heating function is activated.
Optional normally open/normally closed contact.
32 (G0) IQlogic control unit
31 (G) IQlogic control unit
Blue
Orange
Black
Red
Green
Yellow
Brown
White alt.
grey
Brown
White
Resistor/air heater/air cooler type, 2.2 kΩ
Insertion-type/
strap-on sensor
Valve actuator
0-10 V DC output signal
0-10 V DC control signal
G0 24 V AC
G 24 V AC

GB.TBIQ3.130915
Swegon reserves the right to alter specifications.
10 www.swegon.com
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
P1
COM POWER
IQlogic+
1234 5678
-+-+ -++-
C
13
NO
14
C
15
NO
16
+
17
-
18
+
19
-
20
G
21
G0
22
Com 1Heat/Cool Com 2
910 11 12
-S -S
To wire a standard air heater for the GOLD, TBLE/
TCLE
The control cable of the standard, type TBLE/TCLE coils are
fitted with a quick-fit connector.
Connect the cable for BUS communication to one of the
ports in the air handling unit’s IQlogic control unit marked
COM1-3.
Electric
air heater
Swegon
Standard
with 8-pin
control cable
Applicable to size 100/120 GOLD
units only:
If the total load on Terminals 58-59
and 60-61 is higher than 16 VA,
use Terminals 201 (G) and 202 (G0).
Terminals 201-202 can be loaded with
a total of max, 48 VA.
When the Season Heating
function is activated.
Optional normally open/
normally closed contact.
32 (G0) IQlogic control unit
31 (G) IQlogic control unit