SwissPhone s.QUAD User manual

www.swissphone.com
s.QUAD Bluetooth Tips
Introduction
In most cases, connecting s.QUAD to smartphones or tablets work right away.
Sometimes however a connection setup will not work immediately. This document
will guide you in these cases, helping to enable the connection. Please let us know
if this document was helpful for you, or not and which areas of the documentation
should be improved. We are looking forward to receiving your feedback!
Setup Connection
Please follow the sequence outlined in the flow below. In case you reach a
rectangle with «bars» on the sides, please jump to the corresponding chapter
inside this document.
After following this flow, hopefully you have successfully connected your
Smartphone and s.QUAD. Now you can read out and change some settings using
the s.QUAD App (in as far as allowed using PSWplus). More on this in the
following chapter.
Change s.QUAD Settings using the App
Once s.QUAD is connected to a smartphone, please open the s.QUAD App. After a
quick time the button at the bottom of the app will turn blue. Now you can read the
current settings from s.QUAD.
Connecting
s.QUAD to
Smartphones
Change Settings
Flow

Now the app will display the parameters according to the rights hat have been defined
in PSWplus. In the example below all “Start” parameter will not be shown in the App, as
there are no rights assigned (-). Alert patterns can be viewed (show) but not changed,
while Display parameters and Terminal Handling may be changed from the App.
Bluetooth-Settings of a s.QUAD in PSWplus.
Rights are as followes:
"-" No rights, settings not visible in App.
"Show" The current settings will be shown in the app, but may not be changed.
"Edit" Settings can be viewed and changed using the app. Once they are written to
the device, they will become effective.
Activeate Bluetooth using PSWplus and on s.QUAD
Depending on how s.QUAD is configured, the Bluetooth menu may already be
available in your s.QUAD. Usually in “Settings Bluetooth”. Here you can enable /
disable Bluetooth.
In case the menu is missing, you may add it to s.QUAD using PSWplus. Simply
“drag & drop” it to the appropriate place inside “Active menu”.
Install App: Google Play and Apple App-Store
On Apple terminals you can find s.QUAD App in the App-Store. Alternatively, please
navigate to the following link: https://itunes.apple.com/de/app/s-quad/id995920716
You can find s.QUAD App for Android inside Google Play using this link:
https://play.google.com/store/apps/details?id=swissphone.sone.pager.droid
Please note that your device must support Bluetooth > = 4.0 in case it does not,
installing will not be possible.
Activate Bluetooth
s.QUAD
Install App

Activate Bluetooth on Smartphone
On first start of s.QUAD Android App, it will ask you to enable Bluetooth. We
recommend you confirm this question. Otherwise, you may enable Bluetooth
following the steps outlined below:
Android
Please enter “Settings” (gear icon), then navigate to Bluetooth and turn it on. On
some Android devices you may find Bluetooth in “Connections” or “Networks”
Apple
Please enter “Settings” (gears icon), Bluetooth and change the switch to «on».
Disconnect Bluetooth
In case it is not possible to set up a connection, it may make sense to first “tear
down” a partial connection completely. After this, a fresh start can be made. To start
over, please follow the steps below:
1) Important, start with s.QUAD:
Please navigate into the Bluetooth menu (usually in “Settings”) and select “Remove
Bond”. Now s.QUAD may ask you to also delete pairing information on the
smartphone.
Android:
Please navigate to «Settings» (gear icon), Bluetooth. Now search for your s.QUAD
(«s-QUAD C2uxyz.abcde»). Touch the gear next to the device name and select
“forget”. Sometimes also “unpair”, “disconnect” “unbond” or similar terms may be
used.
Apple:
Please navigate to “settings” (gears icon), Bluetooth. search for your s.QUAD («s-
QUAD C2uxyz.abcde»). Touch the (i) next to the device name. Now please select
“ignore this device” and confirm.
Now you can re-establish the connection using s.QUAD App.
Software Versions
Please note that both s.QUAD app and firmware are constantly extended and
improved. Please activate the automatic update of the app (or update it regularly by
hand). Depending on the date of manufacture of your s.QUAD, it may be worthwhile
updating the firmware. The current s.QUAD Firmware as of spring 2018 is 2.38.
Activate Bluetooth
Smartphone
Disconnect
Reset-Connection
Updating Software