Symmons Oxford Trim Series Installation instructions

Oxford®
Model Numbers
Oxford Trim Series
Oxford Trim Series with TA-10 Flow Control Spindle & T-12A Cap Assembly
Installation & Operation Instructions
TRIM ONLY
S-4200-TRM
Shower Valve Trim
S-4201-TRM
Shower Trim
S-4202-TRM
Tub/Shower Trim
S-4204-TRM
Tub/Hand Shower Trim
S4208TRM
Shower/Hand Shower Trim
TRIM, TA-10, T-12A
S4200TRMTC
Shower Valve Trim
S4201TRMTC
Shower Trim
S4202TRMTC
Tub/Shower Trim
S4204TRMTC
Tub/Hand Shower Trim
S4208TRMTC
Shower/Hand Shower Trim
S-4200-TRM
S4200TRMTC
S-4201-TRM
S4201TRMTC
S-4202-TRM
S4202TRMTC
S4208TRM
S4208TRMTC
S-4204-TRM
S4204TRMTC
TA-10T-12A
Compliance
• ASME A112.18.1/CSA B125.1
Limited Lifetime - to the original end purchaser in
consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
Go to www.symmons.com/register to register your
Symmons product.
Warranty

2
1. Recommended Tools
FIGURE 2
HH
I
I
J
J
K
K
F
F
B
B
D
D
G
G
L
L
M
M
A
A
C
C
N
N
Q
Q
P
P
O
O
E
E
Floor
Floor
Notes:
1) Valve body and piping not included and shown as reference only.
2) Plaster shield (p/n T-176) for dry wall, plaster or other type walls 1/2" or greater.
3) All dimensions measured from nominal rough-in (see N as reference).
4) Dimensions subject to change without notice.
Phillips Screwdriver
Adjustable Wrench Safety Glasses Thread Seal TapeDrill Allen Wrench (3mm)
FIGURE 1
2. Dimensions
Measurements
A 6-1/2", 165 mm
B 9-5/8", 245 mm
C 3-7/8", 98 mm
D
Male 1/2" IPS thread must
protrude 1/2" from
finished wall
E 6", 152 mm right or left
F 77", 1956
G 3-1/2", 89 mm
H 7-1/2", 191 mm
I 2-1/2", 64 mm
J
Trim with tub spout:
Ref. 32", 813 mm
Trim without tub spout:
Ref. 42", 1067 mm
K 12", 305 mm
L 2-9/16", 65 mm
M 4", 102 mm
N(Rough in)
2" ± 1/4", 51 mm ± 6 mm
O 1/2" NPT
P 4", 102 mm
Q 6-1/2", 165 mm

3
3. Parts Breakdown (Model Numbers Ending in TRMTC)
5. Installation - Adjust Packing Nut (Model Numbers Ending in TRMTC)
1) Turn hot and cold supplies on. Valve will not operate unless both hot and cold water supply pressures are on.
2) Place handle over flow control spindle.
3) Tighten packing nut for positive frictional resistance as handle is rotated from shut-o position across adjustment range.
6. Installation - Setting Limit Stop Screw (Model Numbers Ending in TRMTC)
1) Turn hot and cold supplies on. Valve will not operate unless both hot and cold water supply pressures are on.
2) Place handle on flow control spindle and open valve to maximum desired temperature.
3) Turn limit stop screw clockwise until it seats.
WARNING: Failure to adjust limit stop screw properly may result in serious scalding.
The temperature limit stop screw limits valve handle from being turned to maximum position resulting in excessive hot
water discharge temperatures.
4. Installation - Remove Test Cap (Model Numbers Ending in TRMTC)
1) Check for leaks around the valve assembly and all pipe
fittings.
Flow control spindle (TA-10) and cap assembly (T-12A) will
come factory assembled for all model numbers ending in
TRMTC. When ready to remove Test Cap and install trim,
follow the instructions below:
2) Remove test cap from valve (FIGURE 4.1).
3) If system is dirty, flush valve.
4) Thread flow control spindle and cap assembly into valve
body. Turn clockwise to secure to valve (FIGURE 4.2).
FIGURE 4.1 FIGURE 4.2
LIMIT STOP
SCREW
2
1
PACKING
NUT
FIGURE 3
Replacement Parts
Item Description Part Number
1 Cap Assy. T-12A
2 Flow Control Spindle TA-10
IMPORTANT: Model numbers ending in TRMTC
coordinate with Temptrol pressure balancing valves
ordered with Test Cap. The Test Cap is used to
allow pressurization of system. Do not remove
test cap from valve during wall construction,
installation of valve or pressurization of system.
WARNINGS:
1. Test cap rated for pressure testing up to 200
psi maximum. DO NOT exceed 200 psi while
pressure testing valve body.
2. Do not expose valve with test cap to heat
for longer than 2 minutes when soldering
copper tubing. Doing so may damage the
internal components of the valve and will
void the product warranty.
3. Ensure test cap is re-torqued to 30 lb-ft after
soldering valve body.

4
Notes:
1) Append appropriate sux for premium finish.
2) Append appropriate flow rate to showerhead
or hand shower for low flow.
3) Apply a bead of silicone around the perimeter
of all shower trim installed flush to the
finished wall. Leave opening on bottom of
escutcheons for weep hole.
4) Apply plumber tape to all threaded
connections.
FIGURE 7
K
A
B
H
H
I
C
E
D
F
G
N
M
L
J
EF-109*
*Order in-line vacuum breaker (EF-109) for
hand shower systems without dual checks.
7. Parts Breakdown
Replacement Parts
Item Description Part Number
A Showerhead 422SH
B Shower Arm 422SA
C
D
Shower Handle
Flange T-549
E
F
Lock Nut
Dome Cover T-543
G
H
I
Shower Escutcheon
Screws
Mounting Plate
T-542-NS-K001
JDiverter/Volume
Control Handle T-589
K Tub Spout 422TS
L Hand Shower 422W
M Wall Cradle T-547
N 60" Hose RTS-045

5
FIGURE 8.4
8. Installation - Shower Valve Trim
2) Place diverter/volume control handle into slot in shower
escutcheon (FIGURE 8.2).
3) Secure large shower escutcheon to mounting plate.
Guide handle into control port on valve body. Tabs
should snap in place (FIGURE 8.3).
FIGURE 8.1 FIGURE 8.2
FIGURE 8.3
1) Attach arm and flange to shower pipe. Turn clockwise
to tighten (FIGURE 9.1).
2) Install showerhead to shower arm. Turn clockwise to
tighten (FIGURE 9.2).
9. Installation - Showerhead & Tub Spout
FIGURE 8.5
1) Secure large mounting plate to Temptrol
pressure balancing valve using mounting screws
(FIGURE 8.1).
3) Install tub spout escutcheon and tub spout to
stub out pipe. Turn clockwise to tighten (FIGURE 9.3).
4) Install dome cover and lock nut by turning clockwise
(FIGURE 8.4).
5) Install flange and handle to shower valve. Secure set
screw (FIGURE 8.5).
FIGURE 9.1 FIGURE 9.2
FIGURE 9.3