Symmons SCOT SLC-6000 Series Manual

SCOT®/Metering
Model Numbers
SLC-6000 Series
Metering Lavatory Faucet
Operation & Maintenance Manual
Metering lavatory faucet features 4" centerset
mount, 3/8" copper supply tubes and temperature
limit stop. Vandal resistant 0.5 gpm (1.9 L/min)
aerator limits water flow to a maximum of 0.25 gpc
(0.95 L/cyl) @ 60 psi with a maximum 30
second closing time. Faucet constructed from
brass, plated in standard polished chrome
finish.
Specification
Compliance
Modifications
Note: Append appropriate -sux to model number.
SLC-6000
SCOT Metering Lavatory Faucet
-DP 8" deck plate
-G Grid drain
-IPS 1/2" male IPS connections
-OFG Oset grid strainer -ASME A112.18.1/CSA B125.1
-NSF/ANSI 61.9, NSF/ANSI 372
Dimensions
Measurements
A Ø 1-7/8", 48 mm
B 3-3/4", 95 mm
C
Deck Thickness Ref.
Min. 1/2", 13 mm
Max. 1", 25 mm
D 1-3/8", 35 mm
E 2-1/8", 54 mm
F(2x) Hole Size
Ø 1/2", 13 mm
GHole Size
Ø 1-1/4", 32 mm
H11", 279 mm
I4", 102 mm
J5-3/4", 146 mm
K 1-1/2", 38 mm
L 2-1/4", 57 mm
M 1-1/8", 29 mm
N 3-5/8", 92 mm
O 3/8", 10 mm
JJ
AA
BB
HH
DD
CC EE
GG
II
KK
LL
MM
NN
FF
OO
TAPETAPE
Note: Dimensions subject to change without notice.
Limited Lifetime - to the original end
purchaser in consumer/residential
installations.
10 Years - for commercial/industrial
installations. Refer to
www.symmons.com/warranty for
complete warranty information.
Warranty

Replacement Parts
Description Part Number
A
B
Handle
Set Screw RL-290
B Set Screw LL-27
CCycle Timing Washers (7) LL-28
D
E
F
Nut
Limit Stop Washer
Limit Stop Washer, Fixed
RL-268
G Upper Housing LL-3N
G1 Upper Housing O-rings (3) LL-48
G1
H3
H4
H5
H10
Upper Housing O-rings (3)
Cartridge O-ring
Cartridge O-ring
Guide O-ring
Piston Quadring
RL-272
HCartridge
Quick Closing Cartridge
LL-1A
LL-1B
H1
H6
Control Spindle Kit
Piston Assembly RL-266
H2 Thrust Washer LL-35
H6 Piston Assembly LT-4AA
H11 Piston Spring/Cylinder RL-267
J0.5 gpm Vandal Resistant
Aerator Kit with Key RL-292
K
L
Check
Spring RL-269
R
S
T
Mounting Bracket
Spacer
Mounting Nut
SPF-KIT
W Check/Screen Assembly LL-71B
X1, X2 8" Deck Plate Assembly RL-291
Y Washer TMX-06527-1
Parts Breakdown
B
A
C
D
E
F
G
H
I
JKM
L
O
N
P
Q
R
S
T
U
V
W
DO NOT
REMOVE TAPE
X1
X2
Y
Installation / Tools Required
Water lines MUST be thoroughly flushed BEFORE and AFTER installing the faucet to prevent foreign matter i.e.
copper chips, sand, stones, etc. from clogging and possibly damaging the sealing surfaces of the cartridge.
Notes: 1) Recommended minimum operating water supply pressure is 40 psi.
2) Supply stop valves must have 3/8" O.D. compression outlet.
1
2
U
V
W
1
2
3
3
Y
1) Remove compression nuts (U) and
ferrules (V) from supply stops. Re-
tain for installation to faucet copper
tubing. Ensure washer is in place
before installing. Install check/screen
assemblies (W) to supply stops.
2) Install faucet (I), threaded rods (M),
mounting gasket (Q), and 3/8" cop-
per tubing (P) to deck surface.
M
1
3
R
2
S
T
4
3) Place mounting brackets (R) and
spacers (S) onto threaded rods (M).
Secure hardware by tightening
mounting nuts (T) clockwise.
33
1
2
U
P
V
W
2
A
J
1
3
4
5) Remove aerator (J). Turn handle (A)
to full cold position. Open supply,
holding down handle for 10 seconds.
Rotate handle to full hot position,
open supply and repeat above
procedure. Hold down handle and
rotate from left to right to flush lines
completely.
6) After faucet has been operated
through a number of cycles, and sup-
ply water temperature is at desired
levels, adjustments to these features
can be made (see page 4).
I
M
Q
P
Important: DO NOT REMOVE
tape on copper tubing.
CAP AND CARTRIDGE ASSEMBLY
G1
H6
H11
G
H
H3
H4
H5
H7
H8
H9
H10
H12
H13
H14
H1
H2
Adjustable Wrench Allen Wrench: 2.5 mm Phillips Head Screwdriver
4) Connect compression nuts (U) and
ferrules (V) to copper tubing (P).
Carefully bend copper tubing (P) to
meet check/screen assemblies (W).
Attach compression nuts to check/
screen assemblies.
7) Optional 8" Deck Plate: Remove
threaded rods (M) from faucet (I).
Install two screws (X2) through
bottom of deck plate (X1) into
faucet (I). Install faucet and deck
plate to deck surface.
3
3
I
M
12
X2
X1
I

Installation with MAXLINE™Thermostatic Mixing Valve
Installation (adjustments)
2) To limit temperature loosen set
screw (B), remove handle (A), loos-
en nut (D) and turn cartridge stem
(H) to desired maximum tempera-
ture (110°F recommended). Turn
limit stop washer (E) clockwise until
a positive stop is reached against
back of faucet. Reassemble faucet
reversing above procedure.
5
2
B
A
1
3
C
D
4
E
F
H
*
3) For reverse operation (in back to
back installations or when hot sup-
ply is on the right) loosen set screw
(B), remove handle (A), nut (D) and
limit stop washers (E) & (F). Turn
cartridge stem (H) 180° so green
marking* is facing toward front of
faucet. Adjust temperature limit
(see step 2). Reassemble faucet,
reversing the above procedure.
2
B
A
1
3
C
Note: When setting MAXIMUM cycle time,
you MUST maintain at least 5 timing wash-
ers (C) so as not to exceed .25 gal/cyl at 60
psi (per ASME A112.18.1)
Maintenance
2
B
A
1
3
C
DH
E
4
5
6
Note: Faucet will operate from the full
cold position to the maximum hot tem-
perature that has been set.
2
B
A
1
3
C
1) Loosen set screw (B), remove
handle (A) and remove cycle timing
washers (C).
2) Remove nut (D), limit stop washers
(E) & (F) and cartridge housing (G).
3) Remove cartridge (H) and inspect
for debris. Replace cartridge if nec-
essary. Reassemble faucet reversing
procedure outlined in Steps 1 & 2.
1
2
D
E
F
3
G
H
1) Faucet is factory set to shortest cycle
time with 7 cycle timing washers (C).
To increase time, loosen set screw (B),
remove handle (A) and remove
one or more of the washers.
To reduce time, add washers.
Reassemble faucet reversing above
procedure.
MAXLINE THERMOSTATIC
MIXING VALVE
(8210CK)
COLD WATER
BYPASS TEE
FITTING
SCOT FAUCET
(SLC-6000)
TO HOT
WATER SUPPLY
DO NOT
REMOVE TAPE
TO COLD
WATER SUPPLY
FIGURE 1
SLC-6000-ML
TEMPERED
WATER LINE
COLD
WATER LINE
VALVE
OUTLET
Important: DO NOT REMOVE tape on copper
tubing.
For applications using MAXLINE thermostatic mix-
ing valve.
1) Turn o water supplies.
2) Connect tempered water line of faucet to thermo-
static mixing valve outlet (see Figure 1 for piping
reference).
Note: Valve and cold water bypass use compres-
sion
fittings (fittings not supplied).
3) Connect cold water line of faucet to the cold wa-
ter bypass using supplied tee fitting.
4) Connect copper tubing from cold water bypass
tee fitting to thermostatic mixing valve.
5) Connect hot water supply to thermostatic mixing
valve and cold water supply to cold water bypass
tee fitting.
6) Remove aerator from faucet. Turn handle to full
cold position. Open supply, holding down handle
for 10 seconds. Rotate handle to full hot position,
open supply and repeat above procedure. Hold
down handle and rotate from left to right to flush
lines to prevent foreign matter i.e. copper chips,
sand, stones, etc. from clogging and possibly
damaging the sealing surfaces of the faucet car-
tridge.

Symmons Industries, Inc. ■31 Brooks Drive ■Braintree, MA 02184 ■Phone: [phone] ■ Fax: [phone]
Copyright © 2022 Symmons Industries, Inc. ■symmons.com ■[e-mail] ■ZV-3216 REV J ■ 072222
Problem Cause Solution
Faucet runs too long or too short.
Cycle timing washers have not
been
adjusted.
Remove handle (A) then add cy-
cle timing washers (C) to stem to
shorten time or remove washers to
lengthen time.
Faucet drips.
Seat washer worn or foreign mat-
ter (chips, dirt, solder, etc.) is be-
tween washer and seat surface.
Disassemble cartridge (H) and re-
move piston* (H6). Remove screw
(H7) and clean seat washer (H8).
Check control rod pin (H9) for burr
then reassemble.
Faucet runs constantly.
Seat washer not closing on seat
surface or seat washer and/or seat
surface is worn.
Remove piston (H6) and spring**
(H12). Check for burr on pin (H9)
and check spring. Both piston and
spring may have to be replaced.
Excessive wear may require car-
tridge (H) replacement.
Water leaks from under handle. Stem washers worn.
Remove cartridge (H) and replace
with housing o-rings (G1). If leak
persists replace control spindle kit
(H1).
Faucet leaks on or under counter. Supply housing o-rings worn. Replace housing o-rings (G1).
Faucet bleeding between hot and
cold.
LL-71B check/screens NOT in-
stalled.
Two chrome plated 3/8" check/
screens are supplied with every
faucet and MUST be installed.
Faucet bleeding between hot and
cold.
LL-71B check/screens ARE in-
stalled. Replace check springs (K,L).
Handle is loose. Set screw has loosened. Tighten set screw (B).
Handle is sticking to cartridge. Accumulation of sediment in car-
tridge.
Remove handle (A) and all cycle
timing washers (C) from cartridge
(H). Secure handle back onto car-
tridge. After moving handle to the
hot position, cycle faucet by press-
ing down on handle. Cycle faucet
12 times. Remove handle and re-
place timing washers.
Finish is spotting. Elements in water supply may
cause water staining on finish.
Clean finished trim area with a soft
cloth using mild soap and water or
a non-abrasive cleaner and then
quickly rinse with water.
Troubleshooting Chart
Notes: *1) Use caution not to damage piston quadring (H10) while servicing piston assembly (H6).
**2) Do not squeeze ends of spring (H12) causing spring to fully compress.
WARNING: This product can expose you to chemicals including lead, which is known to the state of
California to cause cancer, birth defects, or other reproductive harm. For more information, go to www.
P65Warnings.ca.gov.