Synco G1(A2) User manual

Microphone G1(A2)
User Manual • Uživatelský manuál • Užívateľský manuál •
Használati utasítás • Benutzerhandbuch

2
Content • Obsah • Tartalom • Inhalt
English
3 – 15
Čeština
16 – 28
Slovenčina
29 – 41
Magyar
42 – 54
Deutsche
55 – 67
Importer • Dovozce • Dovozca • Importőr • Importeur
Alza.cz a.s.
Jankovcova 1522/53
Prague 7
www.alza.cz

3
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully before first use
and keep this user manual for future reference. Pay particular attention to the safety instructions. If
you have any questions or comments about the device, please contact the customer line.
✉www.alza.co.uk/kontakt
✆[phone]

4
Caring for Your SYNCO Microphone
•Please keep the product in a dry, clean, dust-free environment.
•Keep corrosive chemicals, liquids and heat source away from the product to prevent
mechanics damage.
•Use only a soft and dry cloth for cleaning the product.
•Malfunction may be caused by dropping, impact of external force.
•Do not attempt to disassemble the product. Doing so voids warranty.
•Please have the product checked or repaired by authorized technicians if any
malfunctions happened.
•Failure to follow all the instructions may result in mechanics damage.
•Warranty does not apply to human errors.

5
Product Instruction
TX Transmitter
1
External Mic Input
5
Low Cut
8
Pocket Clip
2
USB-C Port
6
Pairing
9
Pairing Indicator
3
Power
7
Built-in Mic
10
Power Indicator
4
Reset

6
RX Receiver
1
USB-C Port
5
Channel B Gain Control
8
Pocket Clip
2
Power (Mono/Stereo
Switch) 6 3.5mm Audio Output 9 Pairing Indicator
3
Reset
7
3.5mm Monitoring Jack
10
Power Indicator
4
Channel A Gain Control

7
Indicator Light
Power Indicator (Green)
Pairing Indicator (Blue)
Slow Flashes
Power is lower than 10 %.
Power on.
Fast Flashes
/
System pairing.
Keeps On
It stays green when charging
and is off after fully charged.
System paired.
Flashes twice, turns off,
repeats
/Low cut function is on.

8
Operation and Usage
1. Power Button
Long press the power button for two seconds to turn on/off the system. Short press the power button
on the RX for Mono/Stereo switch.
2. Pairing
The system will pair automatically after power on. If you need manual pairing, long press the channel A
gain control and channel B gain control on the RX, and the pairing button on the TX, the system will
start to pair.
3. Connection
The receiver outputs audio signals to recording devices with a 3.5mm TRRS Phone Cable or 3.5mm TRS
Camera Cable. Please use the corresponding cable based on your device.

9
4. Installation
Attach the transmitter or the external mic to the speaker’s clothing. Install the receiver to the camera’s
hot shoe via the pocket clip.
Note: When using the external mic, please insert it into the mic unput properly.
5. Charging
Please fully charge the TX and RX via the USB-C port and the charging cable before each use.

10
Specifications – Transmitter
Wireless Transmission
Digital 2.4 GHz
RF Frequency Band
2400-2483.5 MHz
Working Distance
50 meters (LOS area), 30 meters (NLOS area)
Latency
12.5 ms
Mounting
Pocket Clip
Audio Input
1/8” / 3.5mm TRS Mic Input
Audio Input Level
1 V (0 dBV)
RF Output Power
< 10 mW
Power Requirements
3.3V – 4.7V
Battery Type
Built-in lithium battery
Battery Charging Time
1.5 hours
Battery Life
5 hours
Dimensions
52×42×16 mm
Material
Plastic
Weight
35 g