How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.9
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
How to Use / mi;ksx dSls djsa Kneading Operation: (Atta, Maida etc.)Steps1.Ensure that the processor in unplugged from thepower supply. (Fig.1)2.Place the bowl on the processor aligning the unlock marking on the bowl & processor unit & turn clockwise to lock. The lock markings of bowl & processor unit should align.3.When the processor bowl is fitted correctly, the processor bowl handle will be the the right of the food processor assembly.4.Place the spindle in the center of bowl as shown in Fig 2.5.Place the kneading blade in the center of the bowl and on the spindle as shown in the Fig 3.6.Fill the flour (Max 350gm) in the processor bowl.7.Holding the processor bowl lid by the feeder tube, lock the lid by rotating clockwise aligning feeder tube with handle of processor bowl. (Fig 4). Ensure tab on the lid clicks into place.8.Plug in the processor.9.Run the processor at speed “1” or “2”.10.Add water gradually through the feeder tube till dough forms into rounded lump.11.Allow it to run for 45 to 60 seconds or till desired consistency is achieved.12.To remove the dough stop the processor and open the lid and turn anticlockwise to unlock the processor bowl and lift. (Fig. 5).13.Remove the dough from the processor bowl; use spatula if required.NOTE:For better results, allow to run till the dough starts ticking on the inner side wall of processor bowl.
