TCL TWC-15CR/UH (ES) User manual

TWC-15CR/UH (ES)
TWC-18CR2/UH (ES)
TWC-22CR2/UH (ES)
TWC-24CR2/UH (ES)

INTRODUCTION
IMPORTANT SAFETYINSTRUCTION ...........................................................................
...................................................................................
PACKINGLIST ............................................................................................................
INSTALLATION &ASSEMBLY INSTRUCTIONS..............................................................
USING YOURAIRCONDITIONER ................................................................................
........................................................................
CAREAND CLEANING................................................................................................
TROUBLESHOOTING .................................................................................................
ELECTRICALREQUIREMENTS
OPERATINGYOURAIR CONDITIONER
1
2
3
4
13
15
16
17

1

2
15K 18K/22K/24K

3
5/8" LongHex-head Screw
1/2" LongHex-head Screw
5/8" LongFlat HeadBolt and
Locknut
5/16" LongHex-head Screw
Sill AngelBracket
1/2" LongFlat HeadBolt and
Locknut
Gasket
Support Bracket(with R and L
remark)

4
15K/18K
17.91 18.625
23.625 26.50
19.00 19.50
28.00 30.00
41.00 41.00
22K/24K

SASH
SASH
1/2 MIN
1/2 MIN
19 MIN
19 1/2 MIN
FIG.1
FIG.3
Storm WindowFrame or Obstruction
Storm WindowFrame or Obstruction
FIG.2
FIG.4
SASH
SASH
1/2 MIN
1/2 MIN
19 MIN
19 1/2 MIN
1/2 MIN
1/2 MIN
Storm WindowFrame
or Obstruction
5
(15K/18K See FIG.1/FIG.2 ; 22K/24K See FIG.3/FIG.4).
Storm WindowFrame
or Obstruction

6
FIG.5
FIG.5 FIG.6
FIG.6
FIG.7 & 8
FIG.7
FIG.8
FIG.9
FIG.9

7
6.Remove the six screws from the cabinet.( ) (FIG.10)There are two screws on the top, left and right.
FIG.10
FIG.11
FIG.11
8. (FIG.12).Remove the shipping block for the 24K
FIG.12
Do not
pull or
lift in
this
area
This may
result in
damage.

8
5/16" Long
Hex-head Screw
FIG.13a
FIG.13a
(FIG.13b-14).
FIG.13b
5/16
Long
Hex-head
Screw
(
)
It is suggested to keep a downward angle so
accumulated rain water can drain out from the
backside of the unit.
FIG.14

9
5/8" Long Flat Head Bolt
Long Flat head
Bolt and Locknut
Long
Flat head Bolt
and Locknut
5/8" Long
Hex-head Screw
1/2" Long
Hex-head Screw
5/8" Long
Hex-head Screw
5
(It should set on the gasket for 22K/24K)
Gasket

5/8" Long
Hex-head Screw
Sash Lock
sash lock
10
FIG.15

11
15K/18K
18 1/4 (46.4 cm)
23 7/8 (60.6 cm)
22K/24K
19 1/2 (49.5 cm)
26 9/10 (68.3 cm)
Y
FIG.16
FIG.18
FIG.17
(Page 6 and 7)

12
FIG.19
FIG.20

13
1
2
3
4
5
6
7
8
9
1. Without timer setting,the
operation mode is Cooling,Dry, Fan andAuto,and
the set temperature willbe displayed.
Time will bedisplayed under timer setting.
Digital Display:
and Button:2. Use these buttons onthe
control panel and remoteto increase or decrease
the Set Temperature or Timer.
Temperature range: 61 ~88 or 16 ~31 .
3. Turn the air conditioner on and
off.
Power Button:
Press the mode buttonto cycle
through the various modes:Cool, Dry, Fan and
Auto.
4. Mode Button:
Use these buttons onthe control
panel and remote toset the Timer.
Timer Off: The timed stopis programmed by
pressing TIMER button.Set the rest timeby
pressing the button or until the rest
time displayed is toyour demand then press
TIMER button again.
Timer On: When the unit isoff, press TIMER
button at the firsttime, set the temperaturewith
pressing the button or . Press TIMER
button at the secondtime, set the resttime with
pressing the button or . Press TIMER
button at the thirdtime, confirm the setting,
Note: It can be set to automatically turn off or on
in 0.5-24 hours. Eachpress of the
buttons will increase ordecrease the timer. The
Timer can beset in 0.5 hoursincrement below 10
hours and 1 hourincrement for 10 hoursor above.
The SET lightwill turn on whilesetting.
To cancel the setfunction, press theTIMER
button again.
then it
will automatically switch onand show on the
display.
5. Timer Button:
Cool Mode: The cooling functionallows the air
conditioner to cool theroom and at thesame time
reduces Air . Press the MODEbutton to
activate the cooling function.To optimize the
function of the airconditioner, adjustthe
temperature and the speedby pressing the button
indicated.
Dry Mode: This function reduces thehumidity of
the air to makethe room more comfortable.Press
MODE button to setthe DRY mode.An automatic
function of alternating coolingcycles and air fan
is activated.
Fan Mode: The conditioner works inonly
ventilation. Press MODE buttonto set the FAN
mode. With pressing FAN SPEED button the
speed changes in thefollowing sequence: Hi, Med
and Lo in FAN mode. Theremote control also
stories the speed thatwas set in theprevious
mode of operation.
humidity
Auto Mode: In AUTO mode the unitautomatically
chooses the fan speedand the mode ofoperation
(COOL,DRY or FAN).In this mode thefan speed
and the temperature areset automatically
according to the roomtemperature (tested by the
temperature sensor which isincorporated in the
indoor unit.).
AUTO
SPEED AUTO MODE

14
When the unit isin ECO mode, the
light will turn on.In ECO mode, theunit will
turn off oncethe room is cooledto the user set
temperature. The fanwill also be off at this point.
The unit will turnback on when theroom
temperature rises above theuser set temperature.
Before the compressor starts,the fan motor will
run for a while,then it will stopfor a while, andwill
repeat to provide amuch more comfortable feeling
and save energy.
6. Eco Button:
Press the SLEEPbutton, the Sleep
Light will be on , and
In SLEEP mode,the air-
conditioner will automatically adjustthe tempera-
ture and fan speedto make the roommore comfor-
table during the night.The set temperaturewill
automatically raise by 1 every 30-60 minutes
and at most changesix times until theset
temperature is .
for 10 seconds then all of the
display lights will turnoff.
.8
82.4
7. Sleep Button:
Press the FAN SPEED button
to choose the fanspeed options. You can choose
Hi, Med, Lo orauto speed in COOL mode and
choose Hi, Med, Loin FANmode.
8. Fan Speed Button:
9. When the Filter Checklight is off,
it is useless topress the Filter Checkbutton. When
the Filter Check lightis on, it canturn off thelight
by pressing the FilterCheck button.After the
fan motor works for500 total hours, theFilter
Check light will turnon to remind theuser to clean
the filter.
Filter Button:
10. To direct the airflow,
horizontal wheel to controlthe horizontal
direction, control the
vertical direction.
use the and use the airdeflectors to
Directional Louvers:
horizontal wheelair deflector air deflector

15
Fan Only:
Press the FAN SPEED button to
choose the fan speedoptions. You can choose
Hi, Med, Lo orauto speed in COOLmode and
choose Hi, Med, Loin FANmode.
7. Fan Speed:
To press the DISPLAY button, itcan
switch off/on alllights or LED display.
8. Display:
Use these buttons onthe control panel
and remote to setthe Timer.
Timer Off: The timed stop isprogrammed by
pressing TIMER button.Set the rest timeby
pressing the button or until the rest
time displayed is toyour demand then press
TIMER button again.
Timer On: When the unit isoff, press TIMER
button at the firsttime, set the temperaturewith
pressing the button or . Press TIMER
button at the secondtime, set the resttime with
pressing the button or . Press TIMER
button at the thirdtime, confirm the setting,then
the rest time tonext automatical switching-on
could be read onthe display of themachine.
Note: It can be setto automatically turn off or on
in 0.5-24 hours. Eachpress of the
buttons will increase ordecrease the timer. The
Timer can beset in 0.5 hoursincrement below
10 hours and 1hour increment for 10hours or
above. The SETlight will turn onwhile setting.
To cancel the setfunction, press theTIMER
button again.
5. Timer:
In AUTO mode the unitautomatically
chooses the fan speedand the mode ofoperation
(COOL,DRY or FAN).In this mode thefan speed
and the temperature areset automatically according
to the room temperature(tested by the temperature
sensor which is incorporatedin the indoor unit.).
6. Auto Mode:
Press the SLEEP button, the Sleep
Light will be on , and
In SLEEP mode, the air-
conditioner will automatically adjust the tempera-
ture and fan speed to make the room more comfor-
table during the night. The set temperature will
automatically raise by 1 every 30-60 minutes
and at most change six times until the set
temperature is .
for 10 seconds then all of the
display lights will turn off.
.8
82.4
4. Sleep:
1. Turn theair conditioner on andoff.Power:
2. Press the COOL button to COOLmode.Cool:
and :3. Use these buttons on the control
panel and remote to increase or decrease the
Set Temperature or Timer. Temperature range:
61 ~88 or 16 ~31 .
1
4
5
6
3
3
7
8
10
9
2
When the unit isin ECO mode, thelight
will turn on. InECO mode, the unitwill turn off
once the room iscooled to the userset
temperature. The fanwill also be off at this
point. The unitwill turn back onwhen the room
temperature rises above theuser set
temperature.Before the compressor starts,the fan
motor will run fora while, then itwill stop for awhile,
and will repeat toprovide a much morecomfortable
feeling and save energy.
Press the Fan Onlybutton to FAN
ONLYmode.
9.
10.
Eco:

16
FIG.21
FIG.21

17