Technogym MH650E User manual

1
10/11/2011
carried out by Fabrizio Frattini
Approved by Andrea Borghesi
revision 1/1
MACHINE INSTALLATION MANUAL
KINESIS STATIONS CORE
MH650E
EQUIPMENT NECESSARY FOR THE INSTALLATION
-
-
-
-
-
N.B.
-
-
-
Wrenches T 5-6-8
socket wrench/open end wrench 17
knives
Electric Phillips-head screwdriver and/or Phillips
screwdriver carrier and/or dollies
Bolts and nuts are contained in a special blister pack with relative legend
The housings are extremely delicate (once unpacked they become
dirty very easily)
The weight of the machine is top-heavy towards the seat
- To fix the machine to the ground, position the plates before closing the housings
PEOPLE NECESSARY FOR THE INSTALLATION

carried out by Fabrizio Frattini
Approved by Andrea Borghesi
revision 1/1
2
10/11/2011
General Information
HARDWARE COMPONENTS
Code
Description
Quan
tity
Letter blister
-
code
Description
Quantit
y
H0007114AC Seat unit 1
0Z126
Screw M10x35 8,8 Z
2
0Z306
washer 10.5x20x2 Z
8
T0000252AC
foot unit
1
0Z023AA
Screw 10X65 8.8 Z
2
0Z306
washer 5x20x2 Z
3
0Z126
Screw M10x35 8.8 Z
1
0Z415
self
-
locking nut M10
Z
2
0D004515AC
frame unit
(housing
1
0Z165
M5x10 8.8 Z
2
0C002209AC
rear housing
2
0Z216
Screw M6x35 10.9 Z
1
0
0B001935
washer
1
0G001314
well nut M6
1
H0007216AA
handles unit
2
0N001388AA
handle
2
0N001389AB
plate
2
0Z208
Screw M8x16 10.9 Z
4
0N001523AB
plates for fastening to
the ground
2
0Z438 (no blister)
lower nut M12
1
0Z313 (no blister)
washer 13x24x2,5
3
0Z183 (no blister)
Screw M12x70 8.8 Z
1
Time (minutes) installation standard conditions
Code
Tot persons
T installation
T handling
T
fixing
CNC
2
30
5
5
Machine technical
data

carried out by Fabrizio Frattini
Approved by Andrea Borghesi
revision 1/1
3
10/11/2011
UNPACKING MACHINE
DO NOT USE KNIFE
UNPACKING MACHINE SEQUENCE
Phase 1
Operator A Operator B
Remove cardboard packaging box

carried out by Fabrizio Frattini
Approved by Andrea Borghesi
revision 1/1
4
10/11/2011
Phase
2
Operator A Operator B
Disassemble the right-left wooden frame
(dotted black line)
Remove 2+2 screws fixing right-left of wood
(detail)
Take out and place the machine parts next to the
unpacking area

carried out by Fabrizio Frattini
Approved by Andrea Borghesi
revision 1/1
5
10/11/2011
Phase
3
Operator A
Operator
B
Cut the lower blackties (do not cut the 4 upper ones), position the transport carrier, separate
the wooden frame from the pallet and transport the machine to an area close to the unpacking
N O

carried out by Fabrizio Frattini
Approved by Andrea Borghesi
revision 1/1
6
10/11/2011
Phase
4
Operator A
Operator B
Eliminate the wooden frame "A", eliminate the polyethylene bag

carried out by Fabrizio Frattini
Approved by Andrea Borghesi
revision 1/1
8
10/11/2011
Transport the machine +components to the assembly area using the transport trolley or dollies
depending on the type of area
MACHINE ASSEMBLY SEQUENCE
Phase 1
Operator A-B
Tighten seat unit to frame with 2+2 screws and 2+2 washers, eliminating the support clamp

carried out by Fabrizio Frattini
Approved by Andrea Borghesi
revision 1/1
8
10/11/2011
Phase 2
Operator A Operator B
Insert rear foot to frame unit, tightening the 2 screws
K + 1 screw J + 2+2 washers + nut
tighten all the arms (the screws have already been
preset by Operator B)
unhook 3 arms D, remove plate F, install the arms in the
special housings inserting 2 screws G + 2 washers for
each arm

carried out by Fabrizio Frattini
Approved by Andrea Borghesi
revision 1/1
9
10/11/2011
Phase 3
Operator A Operator B
Remove the packaging of central frame unit L,
slide down the frame in the open slot, tighten
with 2 screws M
Insert 10 threaded pins (well nut) into the
frame unit

carried out by Fabrizio Frattini
Approved by Andrea Borghesi
revision 1/1
10
10/11/2011
Phase 4
Operator A Operator B
Remove the packaging, take out the right housing
and insert into the frame unit starting from the top
and continuing to the bottom, tighten with 5
screws P + 5 washers, insert right handle Q and
tighten with 2 screws R
Remove the packaging, take out the left housing and
insert into the frame unit starting from the top and
continuing to the bottom, tighten with 5 screws P + 5
washers, insert right handle Q and tighten with 2
screws R