Technogym Selection Abductor User manual

S E L E C T I O N
T H E S T R E N G T H E V O L U T I O N
1
Abductor
User manual
All equipment

Abductor 2
Contents
Identification of the manufacturer and equipment ........................... 3
Description of the equipment............................................................ 4
Technical data ................................................................................... 5
Safety devices and warnings ............................................................ 6
Place of installation ........................................................................... 8
Fitting the number holder ................................................................. 9
Lifting and moving the equipment................................................... 10
Routine maintenance ...................................................................... 12
Replacing the padded parts............................................................ 13
Replacing the cable......................................................................... 14
Adjusting cable tension ................................................................... 15
Removing the front protective weight stack panel.......................... 16
Technical Service............................................................................. 17
Storage............................................................................................ 18
Disposal........................................................................................... 19
Using the equipment ....................................................................... 20
User manual ...................................................................................... 1
Contents............................................................................................ 2

Abductor 3
Peso MAX utente: 180 kg
Peso Max di lavoro: vedi pacco pesi
EN957 - 1/2 IC
Technogym S.p.A. - Via Perticari, Gambettola (FC) - Italy
Designed by Technogym - Made in Slovakia - EU
SELECTION MED C97900 - ALJP
Maximum user’s body weight:180 kg
Maximum training weight: see weight block
C97911100001 a
D
E
A
B C F
Identification of the manufacturer and equipment
The equipment and manufacturer identification plate, affixed under the seat, gives the following details:
AManufacturer's name and address
BCE Mark
CSerial number
DMaximum user weight
EEquipment classification
FConsultation of user manual required

Abductor 4
B
C
FE
DH
G
A
Description of the equipment
A Seat: where the user sits to perform the exercise.
B Levers: operated by the user by means of the kneepads (C); before starting to exercise, or between one set and the next, the
starting position can be adjusted so as to modify the range of motion by using the ROM device.
D ROM device: system for adjusting the Range of Motion and the starting position. Adjustments are made by means of the ROM
lever (E).
F Weight stack: the levers (B), operated by the user, move the weights along two guides by means of a cable. A pin (G) is used for
selecting the load, to adjust the exercise effort level.
H Side handgrips: the user can enhance the comfort by holding them during the exercise.

Abductor 5
1420 mm
(56")
850 mm
(34")
1195 mm
(47")
1400 mm
(55")
193 kg (425 lb) + 229 kg 505 lb)
70 kg (140 lb) + 100 kg (200 lb)
Technical data

Abductor 6
Safety devices and warnings
The maximum user weight is 180 kg (397 lb).
The weight stack is covered on the outside by protective panels.
The equipment has no sharp corners.
All parts which come into contact with the user's body are suitably protected with rubber coverings or padding.
Pay particular attention to the parts of the equipment with labels indicating “BEWARE OF
CRUSHING”.
WARNING
During all operations involving transport, maintenance and cleaning, pay attention to
any part of the equipment where body parts may become trapped.

Abductor 7
Safety devices and warnings
WARNINGS
Attention must be paid to the labels attached to the equipment, as they provide
information about possible risks and hazards.
We recommend immediately replacing the labels when they become damaged or difficult
to read.
This symbol accompanies safety warnings. It is used to draw attention to potential risks of personal injury. Pay attention
to all safety warnings accompanied by this symbol to avoid possible injury.

Abductor 8
Place of installation
To ensure safe, comfortable and effective use of the equipment, the place of installation must comply with certain specific requirements;
in particular, before choosing where to install the equipment we recommended that you check that the following conditions are available:
- a temperature between +10°C and +25°C;
- sufficient ventilation to maintain a humidity level between 20% and 90%, when the equipment is in use;
- sufficient lighting to make the area a safe and relaxing place to exercise;
- sufficient clearance on all sides of the equipment, taking into account its maximum dimensions when in use, to ensure safety;
- a flat, stable and vibration-free floor surface, with sufficient load bearing capacity for the equipment’s weight.
If the equipment is to be installed in a public recreation area, the place of installation must comply with all the requirements of the
regulations currently in force.
WARNINGS
The equipment must be installed and used in a place where access and supervision are specifically controlled by the
owner.
When installing the equipment, use suitable personal protective equipment.

Abductor 9
B
A
Fitting the number holder
The number holder must be fixed immediately underneath the top: standing facing
the equipment, attach the number holder on the left, on the cover of guide rail (A).
Find the place where the two screws (B) are to be inserted.
Attach the number holder using the two screws; the pressure used to tighten the
screws is enough to open the holes provided in the cover.
The number holder is optional.

Abductor 10
01083016
A
Lifting and moving the equipment
Snap-on castors (optional) must be used to move the equipment.
WARNING
Move the equipment very carefully, because it may become unstable
and tip over.
The castors for moving the equipment snap on under the feet of the equipment,
after it has been raised, and are held in place by the special straps.
Raise the equipment on the weight stack side, using a pallet truck or fork-lift
truck; and for greater safety place a wedge under the frame to keep the equipment
raised.
Insert the two fixed castors first on one side and then on the other side of the
weight stack: fit castor stems (A) into the holes provided under the equipment
feet, then push hard until they snap in.
WARNINGS
We recommend placing padded material between the frame and the
wedge and between the frame and the machinery used to lift it.
The fixed castors must always be placed underneath the weight stack.