Teknion interpret WWSDC Operating and maintenance instructions

Double- Sided Complete Frame (WWSDC),
Wire Gap Worksurface (WWWRW)
Part and Product Identification
Section:
Description: Page No:
Date:
Rev. No: 2
DOUBLE SIDED COMPLETE FRAME - CURVE LEGS & WIRE GAP WORKSURFACE
FRAMES, SUPPORT & WORKSURFACES
May 2018 1 of 9
INT_001b
interpret Installation Guides
J - 5/16-18x3.75 Length
Hex Cap Screw
(E01-0799) x10
F - 1/4-20x3-12 Flat
Head Machine
Screw Quadrex
Drive
(E01-0771) x4
H - #10x0.875" LG.
Screw, Quad. Pan
Washer
(E07-0077)
48"- 72" x4
78"- 96" x8
G - Front Standoff
(B02-0658)
48"- 72" x2
78"- 96" x4
N - Wire Gap
Worksurface
(WWWRW) x2
B1 - Transverse Beam
Sub-Assembly
(N02-3688) x3
B2 - 5/16- 18x2.5
Long, Socket
Head Cap Screw
(E01-0756) x24
B3 - 5/16- 18 Hex
Nut, 1/2 A/F,
.265 Th
(E01-0755) x24
C - Center Rail End
Cap Assembly
(N02-2149) x2
D - Center Rail
Assembly
(N02-2090) x1
K - 5/16- 18 Hex Nut,
1/2 A/F,.265 Th
(E01-0755)
48"- 72" x10
78"- 96" x14
E - Cantilever Bracket
(A16-4882\12) x2
I - Worksurface
Spacer Block
(A25-0547) x4
M - Screws 5/16-18
x2 1
2LG, Hex
Head, Zinc
(E01-1136) x4
L - Spacer Bracket
(A25-0548) x4
A1 - Curve Leg with
Wood Infill
(N02-2365) x1
OR
Curve Leg with
Glass Infill
(N02-2349) x1
OR
Curve Leg Open
(N02-2363) x1
A2 -Curve Leg
Leveler Add-on
Puck
(A18-0242) x8
N
G
D
I
E
C
B1
L
A1
A2

Section:
Description: Page No:
Date:
REMOVE MOUNTING SCREWS CREATING END GABLE CONNECTION
INT_001b
2 of 9
May 2018
DOUBLE SIDED COMPLETE FRAME - CURVE LEGS & WIRE GAP WORKSURFACE
FRAMES, SUPPORT & WORKSURFACES
interpret Installation Guides
STEP 2: Remove Clamp Brackets from Mid Gable Connection position and move them one
hole over in direction as indicated above.
STEP 1: Remove two mounting Screws and Nuts from each Transverse Beam Assembly Clamp
as shown. Save to use for to Gables installation.
Determine what kind of connection there are on each end.
End Gable
Connection
Mid Gable
Connection
Mid Gable
Connection
B3
B2
B3
B2
B3
B2

Section:
Description: Page No:
Date:
REINSTALL CLAMPS DETAILS
INT_001b
3 of 9
May 2018
DOUBLE SIDED COMPLETE FRAME - CURVE LEGS & WIRE GAP WORKSURFACE
FRAMES, SUPPORT & WORKSURFACES
interpret Installation Guides
STEP 3: Install Clamps to create End Gable Connection. Repeat with all 3 Transverse Beams.
End Gable Connection
End Gable
Connection
Clamp Bracket and
Transverse Tube
alignment.
End Gable Position: You can't see Bolt through the Clamp
Transverse Beam is touching the End Gable
B3
B2

Section:
Description: Page No:
Date:
BEAM AND GABLE CONNECTION INSTALL TRANSVERSE BEAMS TO ASSEMBLY
INT_001b
4 of 9
May 2018
DOUBLE SIDED COMPLETE FRAME - CURVE LEGS & WIRE GAP WORKSURFACE
FRAMES, SUPPORT & WORKSURFACES
interpret Installation Guides
STEP 5 : Fasten together using Socket Cap Screw and Nuts, previously removed from
assembly. Line up the other two transverse beams with the side pair of holes on top of the End
Gable beams as shown above.
STEP 4: Bring End Gables and Central Transverse Beam Assembly together. Assembly is
shipped loosely assembled so there should be enough clearance. Adjust if necessary. Line up the
middle set of holes on the top of End Gable beams with Clamp Brackets holes.
Middle pair of holes.
Position End Gables
with holes facing inward.
B1
A1
B3
B2
B1
NOTE: Insert Bolts into the clamps from the top
when its a Curve Leg with a Solid or Glass infill.

Section:
Description: Page No:
Date:
FASTENING TRANSVERSE BEAMS INSTALLING CANTILEVERS AND SPACERS
INT_001b
5 of 9
May 2018
DOUBLE SIDED COMPLETE FRAME - CURVE LEGS & WIRE GAP WORKSURFACE
FRAMES, SUPPORT & WORKSURFACES
interpret Installation Guides
STEP 6: Fasten together using the previously removed Socket Cap Screws and Nuts .
~32" for frames
78" to 96" long
Max 36"
STEP 7: Place Cantilevers on the top of the Center beam following the specified locations
above. Insert top part of Spacer Block on the middle of the Center Beam. Front Standoff clips
go on both of the side Transverse Beam Assemblies.
Refer to Installation Guides# 401a, 402a, 406a for Wire Management and Electrics section.
~13" for frames
48" to 72" long
B3
B2
G
B1
G
NOTE: Insert Bolts into the clamps from the top
when its a Curve Leg with a Solid or Glass infill.

Section:
Description: Page No:
Date:
CENTER RAIL ASSEMBLY INSTALLING CENTER RAIL ASSEMBLY
INT_001b
6 of 9
May 2018
DOUBLE SIDED COMPLETE FRAME - CURVE LEGS & WIRE GAP WORKSURFACE
FRAMES, SUPPORT & WORKSURFACES
interpret Installation Guides
STEP 8: Prepare Center Rail for installation by sliding mounting Bolts into the channels
underside of the Rail. Slide End Caps on both sides. Tighten Set Screws to secure in place.
SIDE VIEW
STEP 9: Turn Center Rail so that the Hex Cap Screws are facing down. Slide Screws inside the
Rail to line them up with corresponding holes on on the Cantilever, Clamp Brackets and
Worksurface Spacer Block. Drop the Rail on the top of middle Transverse Beam. Make sure all
Screws are inserted into the holes.
D
C
J

Section:
Description: Page No:
Date:
SECURE IN PLACE SPACER BRACKET 78" TO 96" LONG FRAMES
INT_001b
7 of 9
May 2018
DOUBLE SIDED COMPLETE FRAME - CURVE LEGS & WIRE GAP WORKSURFACE
FRAMES, SUPPORT & WORKSURFACES
interpret Installation Guides
STEP 10b: Using the holes on the End Gable labeled above install the Spacer Brackets using
the screws provided.
Underside view
STEP 10: Use Spacer Blocks and Nuts to fasten the Rail to the frame. Install Top Cap if there
are no Screens or Storage specified. Otherwise save it for future installation.
NOTE: Frames 78" to 96" Long require a
Spacer bracket.
I
K
M
K
L

Section:
Description: Page No:
Date:
LEVEL ASSEMBLY AND LOCK LEVELERS
May 2018 8 of 9
INT_001b
DOUBLE SIDED COMPLETE FRAME - CURVE LEGS & WIRE GAP WORKSURFACE
FRAMES, SUPPORT & WORKSURFACES
interpret Installation Guides
STEP 11: Insert Add on pucks, level and square frames. For accuracy Laser Lever is recommended. Lock levelers in position and slide Leveler Covers inside legs.
NOTE:Use as many Pucks as required. They have to be FULLY
ENGAGED and there should be NO SPACE between Pucks and
the bottom of Curve Leg frame.
bottom of Curve Leg frame
A2

Section:
Description: Page No:
Date:
INSTALLING WORKSURFACES INSTALLING WORKSURFACES
INT_001b
9 of 9
May 2018
DOUBLE SIDED COMPLETE FRAME - CURVE LEGS & WIRE GAP WORKSURFACE
FRAMES, SUPPORT & WORKSURFACES
product line Installation Guides
STEP 13: Fasten Worksurface with Washer Screws as shown.
Underside View
Worksurface Inserts
STEP 12: Line up the Wire Gap Worksurface inserts with circular holes on Clamp Brackets.
Drop it on the Frame and fasten with Flat Head Machine Screws.
NOTE: Install Peninsula Support Kit and
Peninsula Worksurface first if specified. Refer to
Installation Guide No. INT_006a and INT_006b
for Information.
Underside View
NOTE: Frames 48" to 72" Long do not include
a Spacer bracket and require 4 less washer screws
to install the worksurface.
F
N
F
H
H