Teknion Sidewise SWDBA User manual

A - Worksurface
Support Assembly
For Customer Support please contact
[email protected]
A3 - Worksurface
Support Cover
(A23-67001) x2
A1 - Cover Without Hole
(N80-67015X) x1
A2 - Cover With Hole
(N80-67016X) x1
B - Murakoshi Screws
(E02-50153) x 6
C - Bolts
(E01-50403) x 6
G2
NOTE: Please refer to Installation
Guide SID_201 to remove all Drawers
in Storage Tower before proceeding
with this Installation Guide.
NOTE: SWCBF shown.
(N80-67004+XXL) x1(R80-67001+XX) x1
E - Screw Kit
(X80-61011) x2
F - Locking Screw
(E01-50793) x3
D - Pedestal Leg Assembly
(N80-67012+24) x1
Or
(N80-67012+29) x1
Or
(N80-67012+36) x1
G1 - Round Surface
(SWWDM486) x1
G2 - "D" Surface
(SWWDB36(XX-XX)6) x1
OR
A
D
I - Wire Management
Tube With
Adhesive Strip
(B11-67000+29) x 1
J - Wire Management Tube
With Adhesive Strip
(B11-67000+11) x 1
H - Freestanding Storage Tower
(STSWCWXX3672XX) x1
Or
(STSWCMAX3672XX) x1
Or
(STSWDWBX3651XX) x1
Or
(STSWDWXXYY72XX) x1
Or
(STSWDWXX3672XX) x1
Or
(STSWLMBX3651XX) x1
H
SWDBA, SWDBB, SWDBC, SWDBD, SWDBE, SWDBF, SWEBB,
SWCBA, SWCBB, SWCBE, SWCBF, SWLMB, SWDMA, and SWCMA
Part and Product Identification
Section:
Description: Page No:
Date:
Rev. No: 0
Sep 2012 1 of 15
SID_001
sidewise

STEP 2: Align the pilot holes on the back of the Covers and Tower.STEP 1: Slide out both Support Covers.
NOTE: Re-insert Covers after Worksurface Support and Worksurface are installed.
A3
A2
A1
A3
A
NOTE: Re-insert Covers after
Worksurface Support and
Worksurface are installed.
H
STEP 1:
Section:
Description: Page No:
Date:
SID_001
2 of 15
Sep 2012
SLIDE OUT COVERS ALIGN SUPPORT ASSEMBLY
sidewise

STEP 3: Secure Worksurface Support and Tower with Screws.
B
DETAIL VIEW
Section:
Description: Page No:
Date:
SECURE SUPPORT ASSEMBLY
Sep 2012 3 of 15
SID_001
sidewise

STEP 4b: Cut Tube as per Specification Drawing. Peel off the cover on Adhesive Strip.
NOTE: Please cut the 280mm Wire Management Tube to 128mm long for 1) Single side, Desk
Height with 24" Wide Storage Tower and 2) Counter Height Storage Tower.
STEP 4a: Peel off the cover on Adhesive Strip.
NOTE: Please refer to Specification Drawing for the length of Tube.
I
J
I
J
NOTE: Please refer to
Specification Drawing
for the length of Tube. NOTE: Please cut the 280mm Wire
Management Tube to 128mm long for
1) Single side, Desk Height with 24"
Wide Storage Tower and
2) Counter Height Storage Tower.
Section:
Description: Page No:
Date:
SID_001
4 of 15
Sep 2012
WIRE MANAGEMENT TUBE (OPTION 1) WIRE MANAGEMENT TUBE (OPTION 2)
sidewise

STEP 5a: Please attach Wire Management Tube as shown for Dual Sided Desk with 36" wide Storage Tower.
SIDE
VIEW
TOP VIEW
BOTTOM
VIEW
I
I
I
Section:
Description: Page No:
Date:
ATTACH WIRE MANAGEMENT TUBE (DUAL SIDED, DESK HEIGHT WITH 36" WIDE STORAGE TOWER)
Sep 2012 5 of 15
SID_001
sidewise

STEP 5b: Please attach Wire Management Tube as shown for Counter Height Storage Tower.
SIDE
VIEW
TOP VIEW
BOTTOM
VIEW
J
I
I
JJ
Section:
Description: Page No:
Date:
ATTACH WIRE MANAGEMENT TUBE (COUNTER HEIGHT STORAGE TOWER)
Sep 2012 6 of 15
SID_001
sidewise

STEP 5c: Please attach Wire Management Tube as shown for Single Side, Desk Height with 24" Wide Storage Tower.
SIDE
VIEW
TOP VIEW
BOTTOM
VIEW I
I
J
J
I
J
Section:
Description: Page No:
Date:
ATTACH WIRE MANAGEMENT TUBE (SINGLE SIDED, DESK HEIGHT WITH 24" WIDE STORAGE)
Sep 2012 7of 15
SID_001
sidewise

STEP 5d: Please attach Wire Management Tube as shown for Single Side, Desk Height with 30" Wide Storage Tower.
SIDE
VIEW
TOP VIEW
BOTTOM
VIEW
I
I
J
J
J
I
Section:
Description: Page No:
Date:
ATTACH WIRE MANAGEMENT TUBE (SINGLE SIDED, DESK HEIGHT WITH 30" WIDE STORAGE)
Sep 2012 8 of 15
SID_001
sidewise

STEP 7: Run Cable into Storage Tower.STEP 6: Guide Cable through Worksurface Support.
BOTTOM VIEW
Section:
Description: Page No:
Date:
SID_001
9 of 15
Sep 2012
GUIDE CABLE THROUGH SUPPORT RUN CABLE INTO STORAGE TOWER
sidewise

STEP 8b: Insert Cable into Wire Management Tube.STEP 8a: Insert Cable into Wire Management Tube.
BOTTOM VIEW
Section:
Description: Page No:
Date:
SID_001
10 of 15
Sep 2012
INSERT CABLE (DESK HEIGHT) INSERT CABLE (COUNTER HEIGHT)
sidewise

STEP 10: Rotate The Top Plate from Pedestal Leg to the same height as the Bridge
Connection.
NOTE: Please refer to next page and Specification Drawing for the height of the Pedestal Leg.
STEP 9: Remove Locking Screws from Pedestal Leg.
F
D
Section:
Description: Page No:
Date:
SID_001
11 of 15
Sep 2012
REMOVE LOCKING SCREWS ADJUST HEIGHT
sidewise

NOTE: Please measure the height of the Bridge Connection and adjust the Pedestal Leg to the same height. Align the pilot holes under Worksurface corresponding to Pedestal Leg and
Worksurface Support.
SIDE VIEW
FINISHED
FLOOR
ALIGN
ALIGN
NOTE: Align the pilot holes under
Worksurface corresponding to Pedestal
Leg and Worksurface Support.
Section:
Description: Page No:
Date:
NOTE
Sep 2012 12 of 15
SID_001
sidewise

STEP 12: Remove Worksurface, and fasten Screws on Pedestal Leg as shown to lock it in the
adjusted height.
STEP 11: Lay Worksurface on Bridge Connection and Pedestal Leg, then level it.
Section:
Description: Page No:
Date:
SID_001
13 of 15
Sep 2012
LEVEL WORKSURFACE SECURE PEDESTAL LEG
sidewise

STEP 13: Secure Worksurface on Support and Pedestal Leg with Screws.
E
G2
C
DETAIL VIEW
DETAIL VIEW
Section:
Description: Page No:
Date:
SECURE WORKSURFACE
Sep 2012 14 of 15
SID_001
sidewise

STEP 14: Re-insert Worksurface Support Cover.
NOTE: Make sure to use the Support Cover with hole for the Power Bar side.
NOTE: Make sure to use
the Support Cover with
hole for the Power Bar side.
Section:
Description: Page No:
Date:
RE-INSERT WORKSURFACE SUPPORT COVER
Sep 2012 15 of 15
SID_001
sidewise