Teknion dossier ZJNL User manual

ZJNL, ZJNC, ZJNI, ZJNN, ZJNM, ZJNO Part and Product Identification
A - Worksurface
(C56-0010) x1
For Customer Support please contact
[email protected]
dossier
Section:
Description:
Page No:
Date:
Rev. No:
DOS_008_G01
1 of 8
Sept 2013
0
B1 - Post Leg with Wire
Access
(X58-0019) x1
or
B2 - Post Leg without Wire
Access
C - Post Leg Screw
(SC023) x8
D1 - Flush Plate
(D56-0006) x1
D2 - Flush Plate Screw
(E57-0023) x8
D - (X56-0001) x3
Optional for
ZJNL, ZJNC, ZJNI
NOTE: Run-Off with Post Leg - Centered
Modesty, Flush Crendenza Connection
(ZJNC), and Standard Desk with Partial
Modesty (ZJSP) shown as an example.
B
A
F - #8 X 2 1/2" Flat Head Wood Screw
(SC065) x 3
Optional for ZJNN, ZJNM, ZJNO only
D1
E - Modesty Kit x1
Optional for ZJNC, ZJNI, ZJNM, ZJNO only
E1 - Modesty x1
E2 - Modesty Bracket
(D56-0004) x2
E3 - Modesty Bracket Screws
(E57-0002) x8
E4 - Cam
(B57-0002) x4
E5 - Titus Shaft
(B57-0001) x4
E
ZJSP

STEP 2: Secure Post Leg with Worksurface with Screws provided.
NOTE: Please skip to Page 4 Step 8 if Modesty is NOT specified.
STEP 1: Flip Worksurface up-side-down. Place Post Leg on the Center of the Worksurface and
1-7/8" away from the edge.
dossier
Section:
Description:
Page No:
Date:
DOS_008_G02
2 of 8
Sept 2013
ALIGN POST LEG SECURE POST LEG
C
L
1-7/8"
Top
View
A
B1 C
C
L

STEP 4: Insert Modesty in the Titus Shafts as shown.
STEP 3: Please insert Titus Shafts into the bottom of Worksurface.
NOTE: Centered Modesty shown as an example.
STEP 5: Insert Cams into Modesty and rotate them to secure Modesty in place.
dossier
Section:
Description:
Page No:
Date:
DOS_008_G03
3 of 8
Sept 2013
INSERT TITUS SHAFTS
ATTACH MODESTY
INSERT CAMS
E5
E1
E4
NOTE: Centered Modesty
shown as an example.
Detail View

STEP 7: Fasten Modesty Brackets to Worksurface and Modesty as shown.STEP 6: Attach Modesty Brackets to Worksurface and Modesty equally.
NOTE: Installers to determine locations to attach Modesty Brackets. Location of Brackets
should not interfere with previously installed Cams.
dossier
Section:
Description:
Page No:
Date:
DOS_008_G04
4 of 8
Sept 2013
ATTACH MODESTY BRACKETS SECURE MODESTY
E2
E3
Detail View
NOTE: Installers to determine
locations to attach Modesty
Brackets. Location of Brackets
should not interfere with
previously installed Cams.

STEP 9: Lay Run-Off onto Flush Plate, and align with Desk as shown on bottom View.STEP 8: Fasten Flush Plates under the Desk Worksurface.
NOTE: Please refer to Installation Guide DOS_007a for Overlap Mount, and DOS_004a for Spacer Mount.
dossier
Section:
Description:
Page No:
Date:
DOS_008_G05
5 of 8
Sept 2013
ATTACH FLUSH PLATES ATTACH RUN-OFF
Bottom View
Underside View
Underside View
Side View
ZJSP Desk Worksurface
Desk
Run-Off
D2
D1
D2
D1
NOTE: Flush Mount option
shown. Please refer to
Installation Guide DOS_007a
for Overlap Mount, and
DOS_004a for Spacer Mount.
Make sure to continue on this
Installation Guide with Step 6
for leveling Run-Off and
Wiring.
ZJSP Desk Worksurface

STEP 10: Fasten Run-Off with Flush Plate as shown.
dossier
Section:
Description:
Page No:
Date:
Page No:
Date:
SECURE RUN-OFF
Sept 2013
6 of 8
DOS_008_G06
D2
Underside View

STEP 11: Use leveler to make sure the Run-Off and Desk are leveled. Adjust Levelers under Post Leg if necessary.
dossier
Section:
Description:
Page No:
Date:
Page No:
Date:
LEVEL RUN-OFF
Sept 2013
7 of 8
DOS_008_G07
Leveler Underside View

Optional: Pull off Wire Access Cover. Place cable inside the Post Leg as shown, then close Wire Access Cover.
dossier
Section:
Description:
Page No:
Date:
Page No:
Date:
WIRE MANAGEMENT
Sept 2013
8 of 8
DOS_008_G08
Underside View