Teknion District Series User manual

Part and Product Identification
Section:
Description: Page No:
Date:
Rev. No: 2
Dec 2015 1 of 5
DIS_102b_G01
district
Convertible Panel Wall with Accessory Beam (UAFCR) &
Convertible Panel Wall Base and Foot Trim (UNPCF)
For Customer Support please contact
[email protected]
A - Convertible Panel Frame Assembly
(N02-1553) 24"-60"x1 66"-96"x2
UAFCR
UNPCF
B1 - Hex Flange Locking Bolt
5/16-18x3.5-in Long Plate
(E03-0430) x1
B2 - Flat Washer
(E03-0457) x2
B3 - 5/16-18 Lock Nut Zinc Plate
(E03-0437) x1
C1 - Center Rail Extrusion Cap
(A23-4058) x1
C2 - Center Rail
(A23-4840) x1
C3 - 5/16-18x2 Hex Cap Screw Grade 2
(A23-4840)
24"-35"x2 36"-60"x4 62"-96"x6
C4 - Flat Washer
(E03-0457)
24"-35"x2 36"-60"x4 62"-96"x6
C5 - 5/16-18x2 Lock Nut Zinc Plate
(E03-0437)
24"-35"x2 36"-60"x4 62"-96"x6
D1 - Base Trim
(A15-8542) 24"-60"x1 62"-96"x2
D2 - Elevated Foot
(A15-8546) 24"-60"x2 62"-96"x4
D3 - #12x1"Long, Type AB, Truss Head,
Tapping Screw, Black
(E07-0050) 24"-60"x3 62"-96"x6
B - (X01-1747)
24"-60"x3 66"-96"x6
C - (N02-2834) 24"-60"x1 66"-96"x2
NOTE: 72" Convertible Panel Wall with
Accessory Beam (UAFCR) & Convertible
Panel Wall Base and Foot Trim (UNPCF)
shown as an example
B1
B2
A
C2
C1
B3
D2
D1

Section:
Description: Page No:
Date:
INSTALL BASE TRIM ELEVATED FEET INSTALLATION
DIS_102b_G02
2 of 5
Dec 2015
district
STEP 1: Lay down Convertible Panel Frame and place Base Trim underneath lower horizontal
tube. Make sure Base Trim is centered with respect to Panel. Secure in place with tapping
screws included.
NOTE: If Freestanding Foot is specified, please refer to Installation Guide DIS_101c for
instructions and continue with Elevated Panel Wall installation Guide STEP 2.
STEP 2: Bring Elevated Feet on an angle and push though the tape into holes located on the
outside edge of vertical tube.
A
A
D2
D1
D3
D1
Front View
Detail View
NOTE: If Freestanding Foot is
specified, please refer to Installation
Guide DIS_101c for instructions and
continue with Elevated Panel Wall
installation Guide STEP 2.

STEP 1:
districtdistrict
Section:
Description: Page No:
Date:
FRAMES ASSEMBLY (OPTIONAL)
Dec 2015 3 of 5
DIS_102b_G03
STEP 3: Align holes on both Frames, then secure with Bolt, Washers and Nuts as shown.
NOTE: This step only applies to 66"-96" Convertible Panel Walls.
B3
B1
B2

Section:
Description: Page No:
Date:
INSERT BOLTS ACCESSORY BEAM ASSEMBLY
DIS_102b_G04
4 of 5
Dec 2015
district
C2
C4
C5
STEP 5: Attach Accessory Beams with the Frames, then secure with Washers and Nuts.
Detail View
STEP 4: Insert Bolts inside the channel on the bottom side of the Accessory Beam as shown.
Slide Bolts to approximately location to be inserted into the Frame.
C3
Underside View

Section:
Description: Page No:
Date:
LEVEL INSERT EXTRUSION CAP
DIS_102b_G05
5 of 5
Dec 2015
district
C1
STEP 7: Insert Extrusion Cap into the Accessory Beam as shown.
Underside View
STEP 6: Level Convertible Panel Wall and adjust levelers if necessary.