Tektronix 80C14 User manual

xx
80C14
Optical Sampling Module
ZZZ
User Manual
*P071295500*
071-2955-00

80C14
Optical Sampling Module
ZZZ
User Manual
xx
www.tektronix.com
071-2955-00

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tektronix.com to find contacts in your area.

Warranty
Tektronix warrants that this product will be free from defects in materials and workmanship for a period of three
(3) years from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at
its option, either will repair the defective product without charge for parts and labor, or will provide a replacement
in exchange for the defective product. Parts, modules and replacement products used by Tektronix for warranty
work may be new or reconditioned to like new performance. All replaced parts, modules and products become
the property of Tektronix.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of
the warranty period and make suitable arrangements for the performance of service. Customer shall be responsible
for packaging and shipping the defective product to the service center designated by Tektronix, with shipping
charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a location within
the country in which the Tektronix service center is located. Customer shall be responsible for paying all shipping
charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage
resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product;
b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage
or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been modified or
integrated with other products when the effect of such modification or integration increases the time or difficulty
of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY
OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
TEKTRONIX' RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE
AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.
TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS
ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
[W4 – 15AUG04]

Table of Contents
General Safety Summary ......................................................................................... iv
Environmental Considerations ................................................................................... vi
Preface............................................................................................................. vii
Specifications................................................................................................. vii
Manual Structure............................................................................................. vii
Related Documentation ..................................................................................... viii
Getting Started ..... .................. ........................................ .................. ..................... 1
Instrument Requirements ..................................................................................... 1
Module Features ............................................................................................... 1
Options and Accessories...................................................................................... 3
Installation...................................................................................................... 4
Operating Basics.................................................................................................... 7
Usage............................................................................................................ 7
System Interaction............................................................................................. 8
Front Panel Controls........................................................................................... 9
Commands from the Main Instrument Front Panel ....................................................... 10
Programmer Interface Commands .......................................................................... 12
User Adjustments............................................................................................. 12
Optimizing Measurement Accuracy........................................................................ 12
Cleaning ....................................................................................................... 16
Reference........................................................................................................... 19
Wavelength, Filter, and Bandwidth Selection . .............. .............. .............. .................. 19
Clock Recovery ............................................................................................... 19
Optical Bandwidth............................................................................................ 19
Glossary
Index
80C14 Optical Sampling Module User Manual i

Table of Contents
List of Figures
Figure 1: Module compartments.................................................................................. 5
Figure 2: Connecting optical cables correctly................................................................... 7
Figure 3: 80C14 optical module front panel..................................................................... 9
Figure 4: Vertical Setup dialog boxes (DSA8200)............................................................. 11
ii 80C14 Optical Sampling Module User Manual

Table of Contents
List of Tables
Table 1: 80C14 module features.................................................................................. 2
Table 2: Standard accessories..................................................................................... 3
Table 3: Available 80C14 options ................................................................................ 3
Table 4: Optional accessories ..................................................................................... 3
80C14 Optical Sampling Module User Manual iii

General Safety Summary
General SafetySummary
Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
While using this product, you may need to access other parts of a larger system.
Read the safety sections of the other component manuals for warnings and
cautions related to operating the system.
To Avoid Fire or Personal
Injury
Ground the product. This product is indirectly grounded through the grounding
conductor of the mainframe power cord. To avoid electric shock, the grounding
conductor must be connected to earth ground. Before making connections to
the input or output terminals of the product, ensure that the product is properly
grounded.
Observe all terminal ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
The inputs are not rated for connection to mains or Category II, III, or IV circuits.
Do not apply a potential to any terminal, including the common terminal, that
exceeds the maximum ratingofthatterminal.
Do not operate without covers. Do not operate this product with covers or panels
removed.
Do not operate with suspected failures. If you suspect that there is damage to this
product, have it inspected by qualified service personnel.
Avoid exposed circuitry. Do not touch exposed connections and components when
power is present.
Wear eye protection. Wear eye protection if exposure to high-intensity rays or
laser radiation exists.
Do not operate in wet/damp conditions.
Do not operate in an explosive atmosphere.
Keep product surfaces clean and dry.
Provide proper ventilation. Refer to the manual's installation instructions for details
on installing the product so it has proper ventilation.
iv 80C14 Optical Sampling Module User Manual

General Safety Summary
TermsinThisManual These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
Symbols and Terms on the
Product
These terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read
the marking.
WARN ING indicates an injury hazard not immediately accessible as you
read the marking.
CAUTION indicates a hazard to property including the product.
The following symbol(s) may appear on the product:
80C14 Optical Sampling Module User Manual v

Environmental Considerations
Environmental Considerations
This section provides information about the environmental impact of the product.
Product End-of-Life
Handling
Observe the following guidelines when recycling an instrument or component:
Equipment Recycling. Production of this equipment required the extraction and
use of natural resources. The equipment may contain substances that could be
harmful to the environment or human health if improperly handled at the product’s
end of life. In order to avoid release of such substances into the environment and
to reduce the use of natural resources, we encourage you to recycle this product
in an appropriate system that will ensure that most of the materials are reused or
recycled appropriately.
This symbol indicates that this product complies with the applicable European
Union requirements according to Directives 2002/96/EC and 2006/66/EC
on waste electrical and electronic equipment (WEEE) and batteries. For
information about recycling options, check the Support/Service section of the
Tektronix Web site (www.tektronix.com).
Restriction of Hazardous
Substances
This product has been classified as Monitoring and Control equipment, and is
outside the scope of the 2002/95/EC RoHS Directive.
vi 80C14 Optical Sampling Module User Manual

Preface
This manual for the 80C14 Optical Sampling Module includes the following
information:
Key features
How to install the module
How to control signal acquisition, processing, and input/output of information
Go to the Tektronix manuals Web site (www.tek.com/manuals) to locate the latest
version of this document.
Specifications
Specifications are located in the specifications and performance verification
document for your main instrument. You can download these manuals from the
Tektronix Web site (www.tek.com/manuals).
To meet measurement specifications:
The instrument was calibrated/adjusted at an ambient temperature between
+20 °C and +30 °C.
The instrument has been operating continuously for 20 minutes within the
operating temperature range specified.
Vertical compensation has been performed with the module installed in the
same compartment used when the compensation was performed. Ambient
temperature must be within ± 2 °C of the compensation temperature.
The instrument must be in an environment with temperature, altitude,
humidity, and vibration within the operating limits described in the
specifications.
Manual Structure
This manual contains the following chapters:
Getting Started shows you how to configure and install your optical module.
Operating Basics describes controlling the module using the front panel and
the instrument user interface.
Reference provides information on wavelength selection, clock recovery,
and optical bandwidth.
80C14 Optical Sampling Module User Manual vii

Preface
Related Documentation
This document covers installation and usage of the sampling module and its
features. For information about the main instrument in which the sampling
module is installed, refer to the user documents and online help provided with
your main instrument.
viii 80C14 Optical Sampling Module User Manual

Getting Started
The 80C14 Series Optical Sampling Module is a high-performance optical
module that supports high bandwidth telecom and datacom standards including
16 GFC Fibre Channel and 14.063 Gb/s Infiniband. The 80C14 Series module is
compatible with the following instruments (mainframes):
DSA8300 Digital Serial Analyzer
DSA8200 Digital Signal Analyzer
CSA8000, CSA8000B, and CSA8200 Communications Signal Analyzers
TDS8000, TDS8000B, and TDS8200 Digital Sampling Oscilloscopes
Instrument Requirements
TekScope application software version 5.1 or greater. Select Help > About
from the TekScope application Help menu to show your current version.
Microsoft Windows XP operating system.
Contact Tektronix Customer Support for information on how to upgrade your
instrument to meet these requirements.
Module Features
Table 1 lists the 80C14 optical module features. (See Table 1 on page 2.)
Afigure in the Operating Basics section shows the module controls, connectors,
and indicators. (See Figure 3 on page 9.)
80C14 Optical Sampling Module User Manual 1

Getting Started
Table 1: 80C14 module features
Feature Description 1
Number of input channels 1
Effective wavelength range 700 nm to 1650 nm
Supported standards or data
filtering rates
8GFC (8.500 Gb/s)
OC-192/STM-64 (9.953 Gb/s)
10GBase-W (9.953 Gb/s)
10GBase-R (10.31 Gb/s)
40GBase-R4 (10.31 Gb/s)
100GBase-SR10 (10.31 Gb/s)
10GFC (10.52 Gb/s)
ITU-T G.975 FEC (10.664 Gb/s)
ITU-T G.709 (10.709 Gb/s)
10 GbE FEC (11.1 Gb/s)
10GFC FEC (11.3 Gb/s)
Super FEC (12.5 Gb/s)
16GFC (14.025 Gb/s)
14G Infiniband FDR (14.0625 Gb/s)
Typical optical bandwidth at
optical connector
>14GHz
Clock recovery support Clock recovery supported with the use of the CR175A
or CR286A Clock Recovery instrument (purchased
separately)
Absolute maximum
nondestructive optical input 2
4mWave
rage power (850 nm)
2 mW average power (1350 nm, 1550 nm)
10 mW peak power for 60 ms.
Internal fiber diameter 62.5 mm/125 μm multimode mode 3
Optical return loss > 14 dB for multimode fiber > 24 dB for single-mode fiber
Output zero < 1 μW immediately after dark calibration ±2% (vertical
offset)
Independent channel deskew Standard
Offset capability at front of
module
Standard
Power meter Standard
1Some values in the table are typical.
2The optical input powers below nondestructive levels may exceed saturation and compression limits of the module.
3Compatible with single-mode fiber of equal or smaller diameter.
2 80C14 Optical Sampling Module User Manual

Getting Started
Options and Accessories
This section lists the standard and optional accessories available for the sampling
modules.
Standard Accessories The following accessories are shipped with the module:
Table 2: Standard accessories
Item Part number
Certificate of Traceable Calibration for
product at first shipment
Not orderable
SMA male 50 Ωtermination (installed, one
for each buffered electrical output connector)
015-1022-XX
Fiber cleaning kit 020-2494-XX
Options The following table lists available sampling module options:
Table 3: Available 80C14 options
Option Description
Option C3 Three years of calibration service
Option C5 Five years of calibration service
Option D1 Calibration data report
Option D3 Three years of calibration data reports (requires Opt. C3)
Option D5 Five years of calibration data reports (requires Opt. C5)
Option R3 Extended repair warranty to three years
Option R5 Extended repair warranty to five years
Optional Accessories You can order the following accessories for use with the sampling modules:
Table 4: Optional accessories
Item Part number
D4/PC Universal Optical Input (UCI) adapter 119-4514-XX
Biconic UCI adapter 119-4515-XX
FC/PC UCI adapter, APC-108 119-5115-XX
SMA 2.5 UCI adapter 119-4517-XX
SC/PC UCI adapter 119-5116-XX
DIN/PC UCI adapter 119-4546-XX
DIAMOND 2.5 UCI adapter 119-4556-XX
SMA UCI adapter 119-4557-XX
DIAMOND 3.5 UCI adapter 119-4558-XX
80C14 Optical Sampling Module User Manual 3

Getting Started
Table 4: Optional accessories (cont.)
Item Part number
ST/PC UCI adapter 119-4513-XX
3.5 male to 3.5 female SMA 015-0552-XX
Slip-on SMA connector 015-0553-XX
CSA8000 & TDS8000 Series Service Manual 071-0438-XX
DSA8200 Service Manual 071-2049-XX
80C14 Series Optical Sampling Module User
Manual (this document)
071-2955-XX
See the Tektronix Web site for the current list of optional accessories.
Installation
Electrostatic Discharge
CAUTION. The electrical data outputs on the optical module are subject to
damage from electrostatic discharge (ESD). To prevent damage from electrostatic
discharge, observe the followig guidelines:
Store the module, with the supplied SMA terminations installed, in a static-free
container, such as the shipping container. Whenever you move the optical module
from one instrument to another, use a static-free container to carry the optical
module.
Be sure to only operate the optical module in a static-controlled environment
(grounded conductive table top, wrist strap, floor mat, and ionized air blower).
Always use a grounded wrist strap (provided with your instrument) when
installing, removing, or handling an optical module or making connections.
Discharge to ground any electrostatic charge that may be present on cables before
attaching the cable to the optical module.
Circuitry in the optical module is very susceptible to damage from overdriven
signals. Verify that the optical signal is within acceptable power levels for the
module before connecting the signal to the module.
4 80C14 Optical Sampling Module User Manual

Getting Started
Correct Module Handling
Guidelines
CAUTION. To avoid damaging your optical module, take the following
precautions:
Never install or remove a module when the instrument is powered on (front-panel
On/Standby power switch is ON).
Do not drop the module since damage and misalignment of the photodiode optical
assembly can result. Store the module in a secure location when not in use.
Place the protective cap(s) on the optical and electrical input connectors when
the module is not in use.
To prevent loss of optical power or damage to the optical connectors, keep the
connectors clean at all times.
Check that all connectors, jumpers, and protective caps are clean before
connecting them to the module. (See page 16, Cleaning the Optical Connectors.)
Module Locations The optical modules fit in the large upper module slots in supported instruments,
such as the DSA8300. The large compartments support single channel modules,
while the small compartments support single or dual channel modules. Eight of
the 10 inputs are usable at one time. (See Figure 1.)
Figure 1: Module compartments
80C14 Optical Sampling Module User Manual 5

Getting Started
At least one module must be installed in an instrument to acquire signals.
NOTE. Installing a large module in either large compartment disables some of
the small compartment channels. Refer to the instrument Online Help about
compartment interaction.
Installing a Module 1. Power off the instrument using the front-panel On/Standby power switch.
2. Plug the grounding strap into the instrument ground connector, and place the
ground strap on your wrist, with contact to skin.
3. Turn the hold-down screws all the way counterclockwise so that they are
completely out and the module retaining tab is flush with the edge of the
module.
4. Insert the module into a compartment and slowly push it in with firm pressure
until it is seated.
5. Turn the hold-down screws clockwise to lock the module in place.
6. Once you have installed the module, power on the instrument. Verify that
the module passes power-on tests.
NOTE. After first installing a sampling module(s) or after moving a sampling
module from one compartment to another, and after the 20-minute instrument
warm-up period, select Utilities > Compensation to run the compensation tool
to ensure optimum measurement accuracy. You must also run a compensation
if an extender is installed, changed, or removed from a module. (See page 12,
Optimizing Measurement Accuracy.)
After running Compensation, save the new values to retain them; otherwise they
are lost when powering off the instrument.
Removing a Module 1. Power off the instrument using the front-panel On/Standby power switch.
2. Plug the grounding strap into the instrument ground connector, and place the
ground strap on your wrist, with contact to skin.
3. Turn the hold-down screws all the way counterclockwise so that they are
completely out and the module retaining tab is flush with the edge of the
module.
4. Slide the appropriate large module ejector lever sideways to unseat the
module from the mainframe connector.
5. Pull on the hold-down screws to remove the module from the slot.
6. Handle the module appropriately (move to another slot in the instrument or
place in a static-protected environment to transport or store the module).
6 80C14 Optical Sampling Module User Manual