Telstra PRE-PAID 3G WI-FI Assembly instructions

GETTING TO
KNOW YOUR
TELSTRA
PRE-PAID
3G WI-FI

LET’S GET THIS SHOW
ON THE ROAD
You must be excited about your brand new Telstra
Pre-Paid 3G Wi-Fi.
This guide will help you get connected as quickly
and as easily as possible. It’ll guide you through
installation and run through all the handy extra
features that are included.
If all goes to plan you’ll be up and running in no time,
so you can get connected while you’re on the move.
2

WHAT’S
INSIDE
03 Safety first
06 Let’s get started
13 Getting connected
25 Wi-Fi home page
20 Extra features
22 Problem solving
25 Extra bits you should know
2

SAFETY
FIRST
Please read all the safety notices before using this device.
This device is designed to be used at least 20cm from
your body. Do not use the device near fuel or chemicals or
in any prescribed area such as service stations, refineries,
hospitals and aircraft. Obey all warning signs where posted.
RADIO FREQUENCY SAFETY INFORMATION
The device has an internal antenna. For optimum
performance with minimum power consumption do not shield
the device or cover with any object. Covering the antenna
affects signal quality, may cause the router to operate at a
higher power level than needed, and may shorten battery life.
RADIO FREQUENCY ENERGY
Your wireless device is a low-power radio transmitter and
receiver. When switched on it intermittently transmits radio
frequency (RF) energy (radio waves). The transmit power
level is optimised for best performance and automatically
3 4

reduces when there is good quality reception. Maximum
power is only used at the edge of network coverage so under
most circumstances the power output is very low. Under poor
network conditions the device transmits at a higher power,
may get hot and have a significantly shorter battery life.
DECLARATION OF CONFORMITY –
SPECIFIC ABSORPTION RATE (SAR)
The wireless device is designed to be used at least 20cm
from the body. We declare that the product detailed in
this manual, and in combination with our accessories,
conform with the essential requirements of The Radio
Communications Standard (Electro-magnetic Radiation
Human Exposure) 2003 and the Australian Communications
and Media Authority Section 376 of the Telecommunications
Act 1997 when used at a distance of not less than 20cm
from the body. The worst case SAR result is published on the
manufacturer’s web site at zte.com.au
N14945
3 4

ROHS DECLARATION
(RESTRICTION OF HAZARDOUS SUBSTANCES)
ZTE declares that the Wireless device is free from
hazardous materials and complies with EU directive
2002/95/EC (commonly known as the RoHS Directive)
and the amendments.
5 6

YOUR PACKAGE CONTAINS THE FOLLOWING:
•TelstraPre-Paid3GWi-Fideviceandbattery
•TelstraPre-PaidNextG®SIM card
•ACchargerandUSBchargingcable
•ThisGettingStartedGuide
•TelstraPre-PaidWelcomeGuide
•Manufacturer’swarrantycard
•Wirelesssecuritycard
LET’S GET
STARTED
5 6

ACCESSORIES AVAILABLE FOR PURCHASE:
•ExternalMemoryCard,availableatmostconsumer
electronic stores. Your Telstra Pre-Paid 3G Wi-Fi supports
microSDcardsupto32GB.ByusingthisdeviceyourTelstra
Pre-Paid 3G Wi-Fi can also act as an external storage drive
whenconnectedviaUSB.
IMPORTANT: SECURITY SETTINGS SSID
AND WI-FI SECURITY KEY
•Thedefaultsecuritysettingsareuniqueforyourdeviceand
are provided on the Wi-Fi security card. Please keep this card
in a safe place.
•Thesecuritykeyiscasesensitiveandshouldbeentered
exactly as it is written on the card. Your Wi-Fi security card
key is also on the device.
7 8

•YoucanchangetheSSID(Wi-Finetworkname)andSecurity
Key (Wi-Fi password) to your own preferences.
•YouneedthisinformationtologontothePre-Paid
Telstra Pre-Paid 3G Wi-Fi.
QUICK REFERENCE SECTION
Wi-Fi home page http://m.home
Wi-Fi home
page password
password
Default SSID
(Wi-Fi network name)
Supplied on Wireless security card.
Default Security Key 10 characters which are case sensitive.
Supplied on your security card and on the
back of the device under the battery.
Restore Defaults To reset your device hold down the
WPSandPowerButton.Thiswillrestore
default passwords.
7 8

YOUR TELSTRA
PRE-PAID 3G WI-FI
Power On/Off
Network Signal
Indicator
Wi-Fi protected
Setup (WPS) button
BatteryLevel
Indicator
Wi-Fi Indicator
USBandChargingPort
9 10

WI-FI INDICATOR STATUS
Solid Wi-Fi is ON
Flashing WPS is enabled,
available for 2 mins
NETWORK INDICATOR STATUS
Solid Not registered on network
Solid Network is registered
Flashing Network data in use
LED INDICATORS
9 10

GETTING
CONNECTED
1. INSERT SIM CARD AND BATTERY
•YourSIMcardshouldalreadybeinsidethedevice.
Check to make sure. Slide the back cover down to remove.
•ToinserttheSIMcard,slideinasshown.
•Insertbatteryandreplacecover.
11 12

2. SWITCH ON YOUR TELSTRA PRE-PAID 3G WI-FI
•PressandholdthepowerkeyuntiltheLEDindicatorslightup.
3. SWITCH ON YOUR COMPUTER OR
WI-FI ENABLED DEVICE
•CheckyourcomputerorotherdevicehasWi-Fienabled
and search for wireless networks. Refer to your Wi-Fi
enabled device manual for further details on searching for
wireless networks.
•SelecttheSSID(Wi-Finetworkname)displayedonyour
security card. Then click connect.
•Enterdefaultsecuritykeyexactlyasshownontheincluded
security card. Note your security key is case sensitive.
You can activate and modify your settings via the Wi-Fi home
page at http://m.home . For more information on the Wi-Fi home
page see page 15.
11 12

4. ACTIVATE YOUR SIM CARD
•Activateonlineviatelstra.com.au/activate
or
•ActivateviatheDevicehomepage,clickonthedesktopicon
called Telstra Pre-Paid 3G Wi-Fi or enter http://m.home into
a browser and click on Account Services located towards the
bottom of the page. Follow the prompts to activate.
If you have any issues activating you can contact our
support centre on 125 8887 or from a non-Telstra phone
call 13 2200 and say “Pre-Paid”.
For more information on activating or managing your
service see your Telstra Pre-Paid Welcome Guide.
13 14

5. ENDING YOUR SESSION
•Switchyourrouteroff,ordisconnectvia
your Wi-Fi network icon status bar.
Handy Hint
You can download the ZTE Wi-Fi Monitor app from
Google Play™ to monitor your Wi-Fi status easily
using an Android™ smartphone.
13 14

WI-FI
HOME PAGE
You can activate, check data usage and manage your settings
via your Wi-Fi home page. You can only access the Wi-Fi home
page while your device is connected.
LOGIN TO YOUR WI-FI HOME PAGE
•Openawebbrowserandenterhttp://m.home
in the address bar.
•EnterthepasswordshownbelowintheAdminlogin
field and click ok.
Password: password
For full details on using your Wi-Fi home page click on Help.
15 16

CHECK DATA USAGE
•Tocheckyourdatausageclickon‘MyDataUsage’linkon
top right hand corner of your Wi-Fi home page.
15 16

HOW TO CHANGE WI-FI HOME PAGE PASSWORD
•GotoSettingsTab,deviceSettings,thenselect
Account Management.
•Inputyourcurrentpassword,thenenteranewpassword
and click Apply.
17 18

TO CHANGE SECURITY KEY (WI-FI PASSWORD)
•GotoSettingsTab,selectWi-FiSettings,
thenselectBasicSettings.
•InputanewSecurityKeyintothefieldPassphrase,
then click Apply.
If changing your password or security key please ensure
you keep a record of it and store in a safe place.
17 18

EXTRA
FEATURES
USING A MEMORY CARD
To use the device as a portable storage drive insert a
microSDHCcardupto32GB:
•Openthememorycardslotcoveronthedevice.
•InsertthemicroSDHCcardasshownandpressgently
to click into place.
•Closethememorycardslotcover.
•Connectthewirelessdevicetoyourcomputerusingthe
USBcablesuppliedandthememorycardwilldisplayas
an external drive.
19 20