Tennsco 1870RH Instruction Manual

PK-1840918
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Deluxe Storage Cabinet with Recessed Handle
Unassembled Models 1870RH & 2470RH
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on products.
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply
in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
LOAD CAPACITIES PER SHELF LEVEL
36w x 18d
36w x 24d
200 lbs.
200 lbs.
UNIT SIZE WEIGHT CAPACITY
Tennsco LLC., Dickson, TN 37056-1888 • [phone]
EVENLY DISTRIBUTED

ASSEMBLY OF 1870RH OR 2470RH CABINET
Tools Needed: A free 11/32” nut driver is included with each Tennsco cabinet.
Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.
2. Place the cabinet back (Ref. No. 1) on a protected surface
to prevent scratching the paint. The ange on the bottom of
the back should be facing upward.
1. The reference numbers used throughout this sheet refer to
the illustration on the back cover. This is to help you to
identify the various parts as they are mentioned.
3. Attach the left side (Ref. No. 2) to the back by placing
ange (A) around the back and bolting it together
with seven bolts and nuts Ref. Nos. 14 & 15). Be sure that
the lances on all shelf adjustment strips (B) point in the
same direction.
5. Insert one shelf (Ref. No. 4) into the approximate center
of the unit, inserting the shelf edges into the lances on
all four shelf adjustment strips. Be sure that the channeled
edge of the shelf is toward the cabinet front.
6. Place the top (Ref. No. 5) onto the unit. Be sure that the
anges tuck inside the cabinet sides and back. Secure
with eleven nuts and bolts. The front part of the top will
bolt into place in step 8.
4. Attach the right side (Ref. No. 3) to the back in the same
manner as in step 3, again making sure that the ange
is around the back and that the lances on the shelf
adjustment strips are pointed in the same direction as those
on the back and left side.
7. With both doors in the closed position, lift the door
and frame assembly (Ref. No. 6) and place it over the
cabinet body. Be aware that the door latches have not
yet been attached,
All lances point UP on
the back and side.
Flanges
face upward
B






so the doors could
potentially swing
open if the door
frame is held in
an upsidedown
position. The
door frame should
cover the outside
edges of the
entire storage
cabinet front.


NOTE: When bolting the unit together, leave
the bolts slightly loose until Step 10, unless
otherwise specified.
Flange faces upward.


Flange goes
under back.
A






8. With the door and frame assembly in place, attach it
securely to the unit by opening each
door, one at a time, and securing
the frame assembly using
two bolts and twenty
nuts. This will
require attaching
nuts to the
nine pre-welded
studs along
each side, plus
two bolts and
nuts along the top.
Using two people, set the unit upright and tighten all nuts
around the entire unit. Insert the remaining shelves at your
desired levels. The shelf you inserted earlier may also be moved
to a different level if desired.
10.
Two holes
must be in front.
Insert shelf
into bottom lances.


Levelers
Access Holes
11. The cabinet must be
level in order for the
doors to close properly.
Levelers may be adjusted
by placing the nut driver
through the hole in each
end of the sill and adjusting
the leveling screw.
9. Place the the bottom (Ref. No. 7) in the lowest notch of the
shelf adjusting strips on the back. Make sure the ange with
two holes faces the front, and that it is over the ange of the
frame sill. If necessary, you may
push out on the side
walls to
enable
the bottom
to more
easily slide
into position. Attach
the shelf securely by bolting
the bottom to the frame sill
with two bolts and nuts.
NOTE: In order to place
the shelves, you must
first tilt the shelf slightly
to the left or right before
inserting it into the unit.

1. Place the locking handle (Ref. No. 9) on the right hand
door and push it until it snaps into place. Then turn the
handle to the open position. The latch should be facing
downward as shown.
2. With the handle still in
the open position, hook
the locking bars (Ref.
No. 8) to the locking
cam (Ref. No. 12).
4. Slide the nylon lock bar guide inserts
(Ref. No. 11) over the lock bar ends
and through the door slots. Push
down rmly until the guides snap
into place.
Handle/Locking System Installation



Outside view
Inside view
3. Slowly rotate the door handle
to the closed position so the
lock bars protrude from the
holes at the top and bottom
of the door (shown below).

REPLACEMENT PARTS









Tennsco Nut Driver
(Ref No. 13)
Bottom
(Ref No. 7)
Left Side
(Ref No. 2)
Top
(Ref No. 5)
Shelf
(Ref No. 4)
Right Side
(Ref No. 3)
Cam Retainer
(Ref No. 12)
Locking Bar Guide
Nylon Insert
(Ref No. 11)
Locking Bar Set
(Ref No. 8)
Locking Cam
(Ref No. 10)
Locking Handle
with Keys
(Ref No. 9)
Back Panel
(Ref No. 1)
REF. NO. DESCRIPTION
1 Back Panel 1 043BA 1 043BA
2 Left Side 1 043LS 1 044LS
3 Right Side 1 043RS 1 044RS
4 Shelf 4 301 4 302
5 Top 1 043TO 1 044TO
6 Door & Frame Assembly 1 043DRH 1 043DRH
7 Bottom 1 043BO 1 044BO
8 Locking Bar Set 1 043LB 1 043LB
9 Recessed Locking Handle w/keys 1 RH-1 1 RH-1
10 Locking Cam* 1 944LC 1 944LC
11 Locking Bar Guide Insert (Nylon) 2 944GI 2 944GI
12 Cam Retainer* 1 944CR 1 944CR
13 Tennsco Nut Driver 1 TOOL-2 1 TOOL-2
14 #8-32 x 3/8” bolts (not shown above) 31 ** 31 **
15 #8-32 nuts (not shown above) 47 ** 47 **
*Included in Ref. No. 9, locking handle with keys (Part No. RH-1). **Available Locally
QTY. PART NO.

Door & Frame
Assembly
(Ref No. 6)
QTY. PART NO.
1870RH (18”d Cabinet) 2470RH (24”d Cabinet)

NOTE: Additional hardware may be included for replacement purposes.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.
49B184