Tennsco 1470RH Instruction Manual

GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on products.
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
PK-1790918
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Standard Storage Cabinet with Recessed Handle
Unassembled Model 1470RH or 1480RH
Tennsco LLC., Dickson, TN 37056-1888 • [phone]
LOAD CAPACITIES PER SHELF LEVEL
36w x 18d
36w x 24d
200 lbs.
200 lbs.
UNIT SIZE WEIGHT CAPACITY
EVENLY DISTRIBUTED

ASSEMBLY OF 1470RH OR 1480RH CABINET
Tools Needed: A free 11/32” nut driver is included with each Tennsco cabinet.
Two people are recommended for assembly. Approximate assembly time: 30-40 minutes.
2. Place the cabinet back (Ref. No. 1) on a
protected surface to prevent
scratching the paint.
The ange on the
bottom of the back
should be facing upward.
1. The reference numbers used throughout this sheet refer
to the illustration on the back cover. This is to help you
to identify the various parts as they are mentioned.
3. Attach the left side (Ref. No. 2) to the back by placing
ange (A) around the back and bolting together with
seven bolts and nuts (Ref. Nos. 17 & 18). Be sure that the
lances on all shelf adjustment strips (B) are pointing in the
same direction.
5. Attach the right side (Ref. No. 3) to the back in the same manner
as you did in step 3, again, making sure that the ange is
around the back and that the lances on the shelf adjustment
strips are pointed in the same direction as those on the back and
left side. Push the side panel up so the studs in the top go
through the holes in the top
ange of the side and
fasten with three
nuts as in
step 4).
6. Attach the sill (Ref. No. 6) to the sides. Place nuts loosely on each
of the studs and slide the ends of the sill into the slots on both
sides of the unit. Then, securely tighten the nuts.
4. Attach the top (Ref. No. 5) to the unit by sliding the outer
ange over the back of the unit and the side ange on
the top over the side panel. The threaded studs should go
through the holes in the top
ange of the
side and
fasten with
three nuts.
Attach the
back to the
top using four
bolts and nuts.
7. Place the rear ange of the bottom (Ref. No. 7) into the
bottom lances of the back. The ange with two holes should
face the front, hanging over the sill. Insert the bolts through
the bottom and still with the head
facing the front of the unit.
Secure with
two nuts.




All lances point UP on
both backs and side.
Flange goes
under back.
Flange faces upward.
Flanges
face upward
Threaded studs go
through the holes
in the flange at the
top of the side.
Slide ends in to the slots
on the bottom of the sides.
Nuts placed loosely
on studs of the sill.
Insert bottom into
bottom lances.
B
A



NOTE: When bolting the unit together, leave
the bolts slightly loose until Step 8, unless
otherwise specified.
NOTE: All illustrations show a solid door. Assembly
for C-Thru doors (CVD1470/CVD1480) is identical.
Two holes must
be in front




8. Set the unit upright and tighten
all nuts around the entire unit.
10. Attach the left door
(Ref. No. 8) to the
unit by placing the
door on the hinges,
aligning the hinge
holes, and dropping
the hinge pins (Ref.
No. 15) into the slots.
Then, tap the top of
each hinge pin until
fully seated.
Leveler
Access Holes
9. Insert the four shelves (Ref. No. 4)
at your desired levels.
NOTE: In order to place the
shelves, you must first tilt
the shelf slightly to the left
or right before inserting
into the unit.
12. The cabinet must be
level in order for the
doors to close
properly. Levelers
may be adjusted by
placing the nut driver
through the hole in
each end of the sill
and adjusting the
leveling screw.
11. Attach the right door
(Ref. No. 9) to the unit
in the same way you
attached the left door.

1. Place the locking handle (Ref. No. 9) on the right hand
door and push it until it snaps into place. Then turn the
handle to the open position. The latch should be facing
downward as shown.
2. With the handle still in
the open position, hook
the locking bars (Ref.
No. 8) to the locking
cam (Ref. No. 12).
4. Slide the nylon lock bar guide inserts
(Ref. No. 11) over the lock bar ends
and through the door slots. Push
down rmly until the guides snap
into place.
Handle/Locking System Installation

Outside view
Inside view
3. Slowly rotate the door handle
to the closed position so the
lock bars protrude from the
holes at the top and bottom
of the door (shown below).






REPLACEMENT PARTS









Tennsco Nut Driver
(Ref No. 16)
Bottom
(Ref No. 7)
Sill
(Ref No. 6) Hinge Pins
(Ref No. 15)
Left Side
(Ref No. 2) Top
(Ref No. 5)
Shelf
(Ref No. 4)
Right Side
(Ref No. 3)
Cam Retainer
(Ref No. 13)
Locking Bar Guide
Nylon Insert
(Ref No. 14)
Locking Bar Set
(Ref No. 10)
Locking Cam
(Ref No. 12)
Locking Handle
with Keys
(Ref No. 11)
Back Panel
(Ref No. 1)
*Included in Ref. No. 11, locking handle with keys and hardware (Part No. RH-1). **Available Locally


Left Door
(Ref No. 8)
Right Door
(Ref No. 9)
NOTE: Additional hardware may be included for replacement purposes.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.
REF. NO. DESCRIPTION
1 Back Panel 1 944BA 1 944BA
2 Left Side 1 944LS 1 292LS
3 Right Side 1 944RS 1 292RS
4 Shelf 4 301 4 302
5 Top 1 944TON 1 292TO
6 Sill 1 944SIN 1 944SS
7 Bottom 1 944BO 1 292BO
8 Left Door 1 944LD 1 944LD
9 Right Door 1 944RD-RH 1 944RD-RH
10 Locking Bar Set 1 944LB 1 944LB
11 Recessed Locking Handle w/keys 1 RH-1 1 RH-1
12 Locking Cam* 1 944LC 1 944LC
13 Locking Bar Guide Insert (Nylon) 2 944GI 2 944GI
14 Cam Retainer* 1 944CR 1 944CR
15 Hinge Pins 6 944HP 6 944HP
16 Tennsco Nut Driver 1 TOOL-2 1 TOOL-2
17 #8-32 x 3/8” bolts (not shown above) 20 ** 20 **
18 #8-32 nuts (not shown above) 30 ** 30 **
QTY. PART NO. QTY. PART NO.
1470RH (18”d Cabinet) 1480RH (24”d Cabinet)
49B179