Tennsco WBHC-1516-MGY Instruction Manual

ASSEMBLY INSTRUCTIONS & PARTS MANUAL
PK-1121018
WBHC-1516-MGY
Cabinet Unit
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on products.
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply
in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
Tennsco LLC. , Dickson, TN 37056-1888 • [phone]

ASSEMBLY OF WBHC-1516-MGY CABINET
Two people are recommended for assembly. Approximate assembly time: 5-10 minutes.
Tools required: slotted screwdriver, Philips screwdriver, and 7/16”wrench or nut driver.
The reference numbers used throughout this sheet refer to the illustration on the back cover.
This is to help you to identify the various parts as they are mentioned.
Assembly for Steel Top
1. One set of mouting brackets (Ref. No. 3) are included with
the standard steel top workbench. Additional sets of
mounting brackets must be purchased separately if
attaching more than one cabinet or drawer.
2. Turn the workbench over, placing the top on a protective
surface. On the underside of the table, slide the mounting
channels front to back into tale anges until channel holes
align with workbench holes. Brackets should be
approximately 14 1/2” apart. Secure each bracket with two
1/4”-20 x 5/8” bolts (Ref. No. 6).
3. Open the cabinet door (Ref. No. 1). Attach the cabinet (Ref. No. 2)
to the mounting channels using four 1/4”-20 x 1/2” bolts.
4. Close the cabinet door and turn the workbench right side
up. Then, reopen the cabinet door and tighten the shelf (Ref.
No. 5). Your cabinet is now ready to use on your workbench.
NOTE: The cabinet can be set up to open from the right or the
left simply by turning the cabinet the direction you would like
it to open and orienting the shelf with the top facing up. Secure
the screws to hold the shelf in place.
NOTE: Workbench sold separately.

Assembly for Wood Top
2. Turn the workbench over, placing the top on a protective
surface. Open the cabinet door (Ref. No. 1). Using a 7/16”
wrench and Phillips screwdriver, remove the shelf (Ref.
No. 5) by unscrewing the four screws. Position the
cabinet in the desired location. Using the cabinet as
a template, mark the location of the four holes for the
wood screws on the underside of the top. Using a 5/32”
drill bit, drill holes into the wood top aout 1/2” to 3/4”
deep. Attach the cabinet housing (Ref. No. 2) to the
top using four wood screws (Ref. No. 8).
3. Close the cabinet door and turn the workbench right
side up. Then, reopen the cabinet door and reinstall the
shelf. Your cabinet is now ready to use on your workbench.
1. When attaching to a wood top, mounting brackets are not
provided or needed. The cabinet can be mounted directly
into the wood top.
NOTE: The cabinet can be set up to open from the right or the
left simply by turning the cabinet the direction you would like
it to open and orienting the shelf with the top facing up. Secure
the screws to hold the shelf in place.
NOTE: Workbench sold separately.

REPLACEMENT PARTS
REF. NO. DESCRIPTION PART NUMBERS
QTY.
1 Door
2 Cabinet Housing
3 30” Mounting Bracket OR
36” Mounting Bracket
4 Recessed Handle w/Keys
1
1
1
1
1
1
1
1
1
WBHC-D
WBHC-H
WBMC-30
WBMC-36
RH-1
WBHC-S
**
**
**
5 Shelf
6 1/4”-20 x 5/8” Bolt
7 1/4”-20 Nut
8 #14 x 3/4”Hex Head Slotted Wood Screw
**Available Locally

1/4”-20 x 5/8” Bolt
(Ref No. 9)
1/4”-20 Nut
(Ref No. 10)
Shelf (Ref No 5)
Mounting Brackets
(Ref No 3)


Door
(Ref No 1)

Cabinet Housing
(Ref No 2)

Recessed Handle
with Keys (Ref No 4)
#14 x 1/4” Hex Head
Slotted Wood Screw
(Ref No. 11)
NOTE: Additional hardware may be included for replacement purposes.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.
49B112