Tennsco Enclosed Foreman’s Desk Instruction Manual

ASSEMBLY INSTRUCTIONS & PARTS MANUAL
RETAIN INSTRUCTIONS FOR FUTURE REFERENCERETAIN INSTRUCTIONS FOR FUTURE REFERENCE
PK-1361018PK-1361018
Enclosed Foreman’s Desk
Tennsco LLC. , Dickson, TN 37056-1888 • [phone]
GENERAL SAFETY INFORMATIONGENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on units.
LIMITED WARRANTYLIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.

ASSEMBLY OF ENCLOSED FOREMAN’S DESK
The reference numbers used throughout this sheet refer to the illustration on the back cover.
This is to help you to identify the various parts as they are mentioned.
1. First, remove all parts from carton and check against the
parts list on back cover for any missing parts. The drawer has
been placed inside the desktop for packaging purposes. While
it is not necessary to remove the drawer to assemble the unit
you may wish to do so for easier access.
Next, attach the desk riser (Ref. No. 1) to the back of the
desktop assembly (Ref. No. 2) using four of the bolts and
nuts supplied. If you have left the drawer inside the desk top,
slide the drawer partially forward for easier access to the
back holes.
2. Using a at surface, bolt the rear panel (Ref. No. 8) to the
back legs (Ref. No. 4), using eight bolts and nuts. Be
sure that the holes in the back legs are situated as shown in
the diagram.
3. Position the side panels (Ref. No. 5) on the inside of the rear
legs, making sure that the hole in the center is at the bottom
as shown in the diagram. Attach using three bolts and nuts
in each panel. Leave the center hole and the bottom hole
temporarily empty to allow for placement of the shelves.
5. Next, attach the inside shelf by bolting it to each side and
to back assembly same as the bottom shelf.
4. Attach the bottom shelf (Ref. No. 6) by bolting the shelf to
each side and to the back legs.
6
6
5
5
8
4
4
2
1
This hole must
be at the bottom
Two people are recommended for assembly. Approximate assembly time: 40-45 minutes.
Tools required: slotted screwdriver, Philips screwdriver, and 7/16”wrench or nut driver.

6. Attach the front assembly (Ref. No. 3) to the front of the unit
by bolting it to each side, as well as to the shelf and unit
bottom, using ten bolts and nuts.
7. Attach the desktop to the unit by bolting the top to each leg
through the pre-welded nuts.
9. Attach the handle to the front of the desk as follows:
a. Place the locking handle (Ref. No. 9) on the right hand
door and fasten with #8-32 bolts with lockwashers that
are encolsed with the handle.
b. Turn handle to open position and place locking cam
(Ref. No. 11) over the square shank of the door handle
with the latch facing downward.
c. Hook the lock bars (Ref. No. 10) to the locking cam
and hold in position while sliding nylon lock bar guide
inserts (Ref. No. 13) over the door lock bar and through
the door slots.
d. Place locking cam retainer (Ref. No. 14) over the square
shank of the door handle and drive it into place.
8. Insert the drawer lock (Ref. No. 12) into the drawer front,
then attach with the accompanying hex nut. If you
removed the drawer from the desktop earlier, reinsert
it now.
13
10
14
10
13
11
9
12
3

REPLACEMENT PARTSREPLACEMENT PARTS
1 Desk Riser SR-12R 1
2 Desktop Assembly SR-13T 1
3 Front Assembly SR-18F 1
4 Back Legs SR-15L 2
5 Side Panels SR-11SP 2
6 Inside/Bottom Shelf SR-29S 2
7 Drawer SR-28D 1
REF. NO.REF. NO. PART NO.PART NO.
8 Rear Panel SR-11RP 1
QUANITYQUANITY
DESCRIPTIONDESCRIPTION
9 Locking Handle w/Keys 944LH 1
10 Lock Bars SR-42LB 1
11 Locking Cam 944LC 1
12 Drawer Lock w/Hex Nut CL-1 1
13 Locking Bar Guide Inserts 944GI 2
14 Locking Cam Retainer 944CR 2
15 1/4”-20 x 5/8” Slotted Screws 42
REF. NO.REF. NO. PART NO.PART NO.
16 1/4”-20 Hex Nuts 34
QUANITYQUANITY
DESCRIPTIONDESCRIPTION
**
**
1 2 3 4
5 6
78 9 10
12
11
13 14 15 16
NOTE: Additional hardware may be included for replacement purposes.NOTE: Additional hardware may be included for replacement purposes.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.However, should your unit contain missing or damaged parts, please contact your purchase location.
**Available Locally
49B13649B136