Tennsco Capstone Shelving Units Instruction Manual

PK-2281018
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
Capstone Shelving Units
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Tennsco LLC. , Dickson, TN 37056-1888 • [phone]
GENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on the units.
LIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.

ASSEMBLY OF A CAPSTONE SHELVING UNIT
Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.
2. Place one shelf support (Ref. No. 5) in the top keyhole slots
of the uprights (Ref. No. 1). Place a bottom shelf support at
the back section, in the bottom keyhole slots on the uprights
as well for stability. Position the front base (Ref. No. 6) inside the
upright posts, with the ange on the oor before inserting the
next shelf support in the front bottom. Place the four plastic feet
(Ref. Nos. 7) on the bottom of the uprights to aid
1. The reference numbers used throughout this sheet refer to
the illustration on the back cover. This is to help you to
identify the various parts as they are mentioned.
3. Place the shelf reinforcement (Ref. No. 4) on the shelf
supports making sure that the gooves in the reinforcement
are connected securely to the edges of the supports. For best
support, divide the space between the reinforcements and
the uprights into equal spaces.
4. Shelves (Ref. No. 2) should be tilted in as shown below. The
square hole on the side ange of the shelf goes to the rear
of the unit. The round hole on the side ange goes toward
the front of the unit.
NOTE: If joining units together, use a “T” post adder upright
instead of an “L” post starter upright.
NOTE: Make sure that all the shelf
supports are seated properly.


NOTE: The narrow part of the
keyhole slot on the uprights
should be toward the oor,
while the wide part should
be toward the top.
UP
DOWN










NOTE: Unit includes plastic fee to prevent posts from damaging
the oor. If you are assembling an Adder unit, you will recieve
the LTNF-T instead of the LTNF-L as show above.

5. Install the rest of the shelves as shown in step 4.
6. Finish off by placing the last shelf on the top of the unit. If
only a single unit was purchased, the shelving unit is now
complete and ready for use.
7. If joining two or more units together, you will use a closed
upright “T” post (Ref. No. 2) to connect the units with the
closed upright “L” posts on the ends.
8. If creating a back to back unit, attach the units together
with a wire post tie (Ref. No. 9) along the top of each
connecting upright post.
ADDITIONAL ASSEMBLY INSTRUCTIONS

Upright “T” Post

Upright “L” Post

REPLACEMENT PARTS

Shelf Reinforcement
(Ref No. 4)

Closed Adder Upright
(Ref No. 2)

Shelf Support
(Ref No. 5)
Plastic “L” Foot
(Ref No. 7)

Front Base
(Ref No. 6)
NOTE: Additional hardware may be included for replacement purposes.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.
REF. NO.
1 Closed Upright Starter Post ddhhLC
2 Optional Closed Upright Adder Post ddhhTC
3 Shelf H-wwdd
4 Shelf Reinforcement HR-dd
5 Shelf Support HS-ww14
6 Front Base FB-wwhh
7 Plastic Foot for “L” Starter Upright LTNF-L
8 Plastic Foot for “T” Adder Upright LTNF-T
9 Wire Post Tie LTCP-1
Where the sufx “ww”, “dd”, or “hh” is used in the part number, the width (ww), depth (dd) or height (hh) is substituted in the
part number. For example, for an 88” high by 15” deep Closed Upright, the part number would be 1588LC.

Shelf (Ref No. 3)
PART NO.
DESCRIPTION

Closed Starter Upright
(Ref No. 1)
Plastic “T” Foot
(Ref No. 8)
Wire Post Tie
(Ref No. 9)
49B228