Tennsco Z Series Instruction Manual

PK-2220719
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
Z-Line Sloping Shelf Unit
RETAIN INSTRUCTIONS FOR FUTURE REFERENCERETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Tennsco LLC., Dickson, TN 37056-1888 • [phone]
GENERAL SAFETY INFORMATIONGENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on units.
LIMITED WARRANTYLIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
LOAD CAPACITIESLOAD CAPACITIES
PER SHELF LEVEL*PER SHELF LEVEL*
36w x 18d
36w x 24d
48w x 18d
48w x 24d
450 lbs.
450 lbs.
350 lbs.
350 lbs.
UNIT SIZEUNIT SIZE WT. CAPACITYWT. CAPACITY
*Load capacities based on evenly distributed loads
Total unit capacity not to exceed 1,500 lbs.

ASSEMBLY OF SLOPING SHELF SHELVING
Tools Needed: A rubber mallet for seating the shelf supports into the uprights.
Two people are recommended for assembly. Approximate assembly time: 20-30 minutes per section.
4. Place the rest of the shelf supports along the top. At the
midway point, install the front-to-back supports. Be sure all
the supports are seated properly into the keyholes.
1. The reference numbers used throughout this sheet refer to
the illustration on the back cover. This is to help you to
identify the various parts as they are mentioned.
3. Attach the shelf supports (Ref. No. 3) to the uprights (Ref.
No. 1 or 2) along the bottom of the unit in the bottom
two holes for the sides and the front. The rear support is
placed 4 1/2” higher than the front support for the correct
angle of the sloping shelf.

2. Depending upon whether you ordered a
single unit or an adder unit, you may have
one or both of the styles of upright
shown. A single unit will use EUR posts
for all four uprights, however if you plan on
installing an adder unit, you should build
your starter unit with two ZTP posts on one
end which will join with the adder. EUR ZTP
NOTE: Top supports will NOTE: Top supports will
all be on the same level.all be on the same level.

9. Finish installing the remaining supports at the desired
distance for each level and install the sloping shelves.
Your shelving unit is now ready to use.
5. Place the steel box formed shelf on the top of the supports
for the top level of the unit.

6. Install the lower sloping shelf onto the supports with the
large ange placed over the rear support and the small
ange resting inside the channel of the front support.



NOTE: Make sure the rear support on each level is 4 1/2” NOTE: Make sure the rear support on each level is 4 1/2”
higher than the front support.higher than the front support.
10. Your shelving unit is now complete and ready for use.

REPLACEMENT PARTSREPLACEMENT PARTS
Sloping Steel ShelfSloping Steel Shelf
(Ref No. 5)(Ref No. 5)


Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.However, should your unit contain missing or damaged parts, please contact your purchase location.
49B22249B222




Front to BackFront to Back
SupportSupport
(Ref No. 3)(Ref No. 3)
Intermediate PostIntermediate Post
(Ref No. 2)(Ref No. 2)
Standard Angle PostStandard Angle Post
(Ref No. 1)(Ref No. 1)
Left to RightLeft to Right
SupportSupport
(Ref No. 4)(Ref No. 4)
Box FormedBox Formed
Steel ShelfSteel Shelf
(Ref No. 6)(Ref No. 6)
REF.REF.
NO. DESCRIPTIONNO. DESCRIPTION
PART NUMBERSPART NUMBERS
ZT7-3618S-5 ZT7-3618A-5 ZT7-3624S-5 ZT7-3624A-5 ZT7-4818S-5 ZT7-4818A-5 ZT7-4824S-5 ZT7-4824A-5ZT7-3618S-5 ZT7-3618A-5 ZT7-3624S-5 ZT7-3624A-5 ZT7-4818S-5 ZT7-4818A-5 ZT7-4824S-5 ZT7-4824A-5
QTY.QTY.
4
2
6
12
5
1
EUR-84
--
DRS-1814
DRS-3614
ZSS-3618
ZMS-3618
--
ZTP-84
DRS-1814
DRS-3614
ZSS-3618
ZMS-3618
Standard Angle Post
Intermediate “T” Post
Front to Back Support
Left to Right Support
Sloping Steel Shelf
Box Formed Steel Shelf
1
2
3
4
5
6
EUR-84
--
DRS-2414
DRS-3614
ZSS-3624
ZMS-3624
EUR-84
--
DRS-1814
DRS-4814
ZSS-4818
ZMS-4818
EUR-84
--
DRS-2414
DRS-4814
ZSS-4824
ZMS-4824
--
ZTP-84
DRS-2414
DRS-3614
ZSS-3624
ZMS-3624
--
ZTP-84
DRS-1814
DRS-4814
ZSS-4818
ZMS-4818
--
ZTP-84
DRS-2414
DRS-4814
ZSS-4824
ZMS-4824
REPLACEMENT PARTSREPLACEMENT PARTS