Tennsco ZA7-4824S-4D Instruction Manual

PK-1930620
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
Z-Line Low Prole Shelving
RETAIN INSTRUCTIONS FOR FUTURE REFERENCERETAIN INSTRUCTIONS FOR FUTURE REFERENCE
Tennsco LLC., Dickson, TN 37056-1888 • [phone]
GENERAL SAFETY INFORMATIONGENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on units.
LIMITED WARRANTYLIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.
ZA7-4824S-4DZA7-4824S-4D ZA7-4824A-4DZA7-4824A-4D
ZA7-4824S-4D withZA7-4824S-4D with
ZAES-4824D extra shelfZAES-4824D extra shelf

ASSEMBLY OF LOW PROFILE SHELVING
Tools Needed: A rubber mallet for seating the shelf supports into the uprights.
Two people are recommended for assembly. Approximate assembly time: 20-30 minutes per section.
4. Place a third front-to-back end support in the middle slots
of the two uprights. This forms one end of the shelving unit.
2. Depending upon whether you ordered a single unit or an
adder unit, you may have one or both of the styles of upright
shown. A single unit will use EUR posts for all four uprights,
as show below in Figure A. If you plan on installing an adder
unit, you should build your starter unit with two ZTP posts
on one end which will join with the adder as shown in Figure B.
1. The reference numbers used throughout this sheet refer to
the illustration on the back cover. This is to help you to
identify the various parts as they are mentioned.
3. With the help from an associate, or using a wall for support,
connect two EUR uprights (Ref. No. 1) using two front-to-
back supports (Ref. No. 3), one at the top and one near the
bottom (leaving the bottom-most keyhole slot empty). Be
sure the front-to-back supports are fully seated in the
keyhole slots as shown.
EUR
NOTE: The uprights must be positioned so that the
narrow part of the slots is toward the floor, as shown.
ZTP
Figure A
Figure B NOTE: There will be only three front-to-back end
supports per unit end, as shown. These are used for
rigidity and are not needed at every shelf level.
Every fourth
keyhole slot is
shaped differently
(with a attened
top) for easier
alignment of
supports.
5. Repeat steps 3 and 4 to construct a second set of unit ends.
If you are planning to install an adder unit, this second end
should consist of ZTP uprights (Ref. No. 2) to act as an
intermediate assembly.







9. If joining more than one unit together, your original unit
should have been assembled with ZTP uprights on one end,
as described in step 5. Simply continue adding shelf supports
and uprights to complete your additional units.
8. If particle board or wire decking was purchased, place the
decking on each shelving level. Particleboard decking should
t ush inside the shelf supports, while wiring decking will
sit slightly below the shelf support edges. If you have
purchased a single unit,
your shelving unit is
now complete.
For adder units,
proceed to step 9.
7. Attach the remaining shelf supports at the desired shelf levels.


6. With the help of an associate, connect the two unit ends
with left-to-right shelf supports (Ref. No. 3). Be sure the
shelf support is oriented as show below.





REPLACEMENT PARTSREPLACEMENT PARTS
DESCRIPTIONDESCRIPTION
QTY.QTY.
REF. NO.REF. NO.
Left-to-RightLeft-to-Right
Shelf SupportShelf Support
(Ref No. 4)(Ref No. 4)


NOTE: Additional hardware may be included for replacement purposes.NOTE: Additional hardware may be included for replacement purposes.
Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.
However, should your unit contain missing or damaged parts, please contact your purchase location.However, should your unit contain missing or damaged parts, please contact your purchase location.
49B19349B193
PART NO.PART NO.
Angle Post (single or starter units only)
“T” Post (adder units only)
Front-to-Back End Support
Left-to-Right Shelf Support
Particleboard Decking OR
Optional Wire Decking
4
--
6
8
4
4
EUR-hh
ZTP-hh
DRS-dd14
DRS-ww14
PB-wwdd
ZWD-wwdd
1
2
3
4
5
6
--
2
3
8
4
4




ZTPZTP
UprightUpright
(Ref No. 2)(Ref No. 2)
Front-to-BackFront-to-Back
End SupportEnd Support
(Ref No. 3)(Ref No. 3)
Particleboard DeckingParticleboard Decking
(Ref No. 6)(Ref No. 6)
EUR UprightEUR Upright
(Ref No. 1)(Ref No. 1)
Wire DeckingWire Decking
(Ref No. 5)(Ref No. 5)
STARTERSSTARTERS ADDERSADDERS
*OPTIONAL*OPTIONAL
EXTRA SHELFEXTRA SHELF
--
--
--
*2
*1
*1
*Additional shelf must be purchased separately. Unit comes standard with four shelf levels with particleboard decking.*Additional shelf must be purchased separately. Unit comes standard with four shelf levels with particleboard decking.