Teuco 382 User manual

690
320
400
400
100
50
50
700
80
330
400
1/2"
1/2"
1400
690
320
400
400
100
50
50
1400
700
80
330
400
1/2"
1/2"
Ø40
Ø40
PRE-INSTALLATION CARD
1/2 1
(1) - At overflow level
Bathtub turned 180°
Standard bathtub
Measurements in mm.
- Hot water connection for 1/2” tap fittings
- Cold water connection for 1/2” tap fittings"
- IPX5 box with PG13.5 - PG9 cable gland
- Electrical connection
- Alarm system connection / chromotherapy
A - The maximum thickness floor tiles for covering 9mm
The product has been designed to be installed on masonry walls. If it is neces-
sary to fix it to different types of walls (wood, plasterboard), adequately rein-
force the wall to guarantee a solid fixing.
N.B. Installation must take place once floors and walls are completed.
Net
Weight
Kg.
Water
Content (1)
lt.
Floor
Load
Kg/m2
Deliv.
Weight
Kg.
Deliv.
Volume
m3
ART. 382
280
Jets N. Water
Capacity l/m.
Air
Flow l/m.
HYDRAULIC CHARACTERISTICS
Whirlpool
Art.
Art.
V Hz
Installed
Power
kW
ELECTRICAL CHARACTERISTICS
Hydromassage
1,2
1,2
TOP+
hydrosilence
230
200
6
230
300
8
50
50
1WLI28
Basic-E
Basic-J 1WBX38
1WLX38
0,95
OPTIONAL
Art.
Installation
Mod.
V Hz
Installed Power
KW
K074+Cromoexperience 1LDX18
230 50
0,09
Top+Hydrosilence+Cromoexperience 2WLI28 1,4
123 280 395 173 1,84
2013.00
ART. 382
(mm 1600 x 800)
67101319600

H
45
1405
850
1600
530
880
800
700
200
700
630
610
570
850
1625
P
170
S
22/2
Data and specifications given are not binding. Teuco Guzzini Spa reserves the right to make changes deemed appropriate without prior notice or obligation to update.
ELECTRICAL INSTALLATION
• The electrical power supply system must be in compliance with national
statutory regulations.
• The product must be connected to the mains power via an omnipolar switch (I)
with an opening between contacts that guarantees complete disconnection in
excess voltage category III conditions (minimum 3 mm), installed outside areas
0,1,2,3 (IEC 60364-7-701).
• Make certain the appliance is connected to the power source by way of a
residual current device with minimum threshold =30mA.
• The electrical connection ( ) must include a connection to the earth
system and must be:
- permanent
- able to handle the rated current (see data plate).
- specified to liquids ingress protection category IPX5.
EQUIPOTENTIAL BONDING
The appliance must be equipotentially bonded by making the connection to the
terminal positioned at the
base of the electric motor/pump unit.
CONNECTION FOR ALARM
SYSTEM
The product is prewired for connection
to the bathroom alarm system (open/
close contact, voltage-free).
HYDRAULIC INSTALLATION
Prepare hot and cold water connections for water supply and the drain connection.
If the hardness of the water of the mains water system is high (>200 mg/litre), it is
advisable to install a water softener to guarantee a good functioning of the
hydromassage installation.
BATHTUBS WITH COMBINED OVERFLOW AND FILLER SPOUT
A DB type device must be installed at least 150 mm above the bathtub rim in
accordance with EN 1717 standard.
ART. 382 TOP
P - Electric Control Panel
S - Remote control
- Dispenser
cap (Ø 50)
BASIC
P- Electric Control Panel
D- Dispenser (Ø 50)
A- Air Regulation (Ø 50)
C- Chromotherapy
60
178
33
120
52
60
178
33
120
52
69 mm
42 mm
C/P
H = 620
H = 620
L N
L: PHASE
N: NEUTRAL
: ALARM SYSTEM (MAX 230/2 40V A.C. 3A)
110
1510
1440
60
590
A
D
P
1500
C
60
130
620
130