Texas Instruments TPS53515 User manual

User’s Guide
TPS53515 Step-Down Converter Evaluation Module User's
Guide
Table of Contents
1 Introduction.............................................................................................................................................................................2
2 Description.............................................................................................................................................................................. 2
2.1 Typical Applications............................................................................................................................................................2
2.2 Features............................................................................................................................................................................. 2
3 Electrical Performance Specifications................................................................................................................................. 2
4 Schematic................................................................................................................................................................................3
5 Test Setup................................................................................................................................................................................4
5.1 Test Equipment.................................................................................................................................................................. 4
5.2 Recommended Test Setup.................................................................................................................................................5
6 Configurations........................................................................................................................................................................ 6
6.1 Switching Frequency Selection.......................................................................................................................................... 6
6.2 Mode Selection.................................................................................................................................................................. 6
6.3 VDD Pin Supply Selection..................................................................................................................................................6
7 Test Procedure........................................................................................................................................................................ 7
7.1 Line and Load Regulation and Efficiency Measurement Procedure.................................................................................. 7
7.2 Control-Loop Gain and Phase-Measurement Procedure...................................................................................................7
7.3 List of Test Points............................................................................................................................................................... 8
7.4 Equipment Shutdown......................................................................................................................................................... 8
8 EVM Assembly Drawing and PCB Layout............................................................................................................................ 9
9 Bill of Materials..................................................................................................................................................................... 13
10 Revision History................................................................................................................................................................. 14
www.ti.com Table of Contents
SLUUAS1C – OCTOBER 2013 – REVISED NOVEMBER 2021
Submit Document Feedback
TPS53515 Step-Down Converter Evaluation Module User's Guide 1
Copyright © 2021 Texas Instruments Incorporated

1 Introduction
The TPS53515EVM-PWR587 evaluation module (EVM) uses the TPS53515 device. The TPS53515 device is a
D-CAP3™ mode, 12-A synchronous buck-converter with integrated MOSFETs. The device provides a fixed 1.2-V
output at up to 12 A from a 12-V input bus.
2 Description
The TPS53515EVM-PWR587 is designed for a regulated 12-V bus to produce a regulated 1.2-V output at up to
12 A of load current. The TPS53515EVM-PWR587 is designed to demonstrate the TPS53515 device in a typical
low-voltage application while providing a number of test points to evaluate the performance of the TPS53515
device.
2.1 Typical Applications
• Servers and storage
• Workstations and desktops
• Telecommunication infrastructure
2.2 Features
The TPS53515EVM-PWR587 features include the following:
• 12-A DC steady-state output current
• Support for a prebias-output voltage at startup
• Jumper, J2, for enable function
• Jumper, J5, for auto-skip and forced-continuous-conduction-mode (FCCM) selection
• Jumper, J7, for extra 5-V input for further power saving purpose
• Convenient test points for probing critical waveforms
3 Electrical Performance Specifications
Table 3-1. TPS53515EVM-PWR587 Electrical Performance Specifications(1)
PARAMETER TEST CONDITIONS MIN TYP MAX UNITS
Input Characteristics
Voltage range VIN 5 12 18 V
Maximum input current VIN = 5 V, IO = 8 A 2.5 A
No load input current VIN = 12 V, IO = 0 A with auto-skip mode 1 mA
Output Characteristics
Output voltage VOUT 1.2 V
Output voltage regulation Line regulation (VIN = 5 V – 14 V) with FCCM 0.2 %
Load regulation (VIN = 12 V, IO = 0 A – 8 A) with FCCM 0.5
Output voltage ripple VIN = 12 V, IO = 8 A with FCCM 10 mVpp
Output load current 0 12 A
Output over current 15 A
Soft-start 1 ms
Systems Characteristics
Switching frequency VIN = 12 V, 1.2 V / 4 A 1000 kHz
Peak efficiency VIN = 12 V, 1.2 V / 8 A 88.5 %
Full load efficiency 86.9 %
Operating temperature 25 °C
(1) Jumpers set to default locations, See Section 6.
Introduction www.ti.com
2TPS53515 Step-Down Converter Evaluation Module User's Guide SLUUAS1C – OCTOBER 2013 – REVISED NOVEMBER 2021
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated

4 Schematic
CLK
DATA
VREG
ALERT#
OPEN= ENABLE
VIN
PGND
VOUT
PGND
SW
PGOOD
ADDR/RF
TRIP
AGND
EN
VDD
MODE
CHB CHA
PM
Bus C
onnector
Input: 8-
14V
Output: 1.2V/0-12A
Ext. VDD
LabView
C
onnector
300k
R4
1.00k
R3
0
R5
1
1
2
2
PEC02SAAN
J2
1
2
3
4
5
6
7
8
9
10
PEC05DAAN
J4
DNP
0
R14
100k
R1
3.01
R9
22uF
C1
22uF
C4
22uF
C3
0.1uF
C7
100k
R2
57.6k
R10
22uF
C2
0.1uF
C5
TP1
TP4
0
R8
TP7
TP9
TP3
TP6
TP2
0
R15
C15
DNP
C16
DNP
R7
DNP
C17
DNP
C9
DNP
0
R19
1uF
C18
1uF
C20
10.0k
R20
10.0k
R21
10
R22
1
2
3
4
5
6
7
8
9
10
PEC05DAAN
J5
20.0kR11
150kR12
150kR13
TP5 TP8
TP10
TP11
TP12
22uF
C6
22uF
C10
22uF
C11
22uF
C12
22uF
C13
22uF
C14
22uF
C19
22uF
C21
22uF
C22
22uF
C23
1
1
2
2
ED120/2
DS
J1
1
1
2
2
ED120/2
DS
J3
TP13
200k
R6
1
122
1
.0 uH
L1
11 22
DNP
L1A
DNP
TP14
TP15
470pF
C8
ADDR/RF
1
PGOOD
2
EN
3
VBST
4
NC
5
SW
6
SW
7
SW
8
SW
9
PGND 10
PGND 11
PGND 12
PGND 13
PGND 14
VIN 15 VIN 16 VIN 17
NC 18
VDD 19
VREG 20
MODE 21
AGND 22
FB 23
VO
24
TRIP
25
26
27
28
PW
PD
29
TPS53515RVE
U1
1uF
C25
1uF
C26
1
2
3
4
5
6
7
8
9
10
PEC05DAAN
J6
1
R16
1
1
2
2
ED555/2
DS
J7
C24
DNP
C27
DNP
VDD_19
VREG
VREG
VREG
VREG
VIN
VIN
VOUT
VOUT
VOUT
VOUT
VDD
VDD
VDD
SW
FB
FB
MODE
PGOOD
PGOOD
AGND
AGND
AGND
AGND
VIN
VOUT
PGND
AGND
PGND
PGND
FB
VR
EG
PGND
VR
EG PGND
VOUT
PGND
MODE
AGND
AGND
AGND
VR
EG
PGOOD
FB
VOUT
VR
EG
VDD
VDD
PGOOD
VOUT
VIN
VDD
PGND
SW
SW
PGND
SW
1
1
TPS53513
NOTES:
PIN 26
PIN 27
PIN 28
TPS53515TPS53915
ALERT#
SDA
SCL
NC
GND1
GND2
NC
GND1
GND2
IC
VARIANT PINOUT FOR U1
TABLE 1
Figure 4-1. TPS53515EVM-PWR587 Schematic
www.ti.com Schematic
SLUUAS1C – OCTOBER 2013 – REVISED NOVEMBER 2021
Submit Document Feedback
TPS53515 Step-Down Converter Evaluation Module User's Guide 3
Copyright © 2021 Texas Instruments Incorporated

5 Test Setup
5.1 Test Equipment
Oscilloscope A digital or analog oscilloscope measures the output ripple. The oscilloscope must be set for
the following: 1-MΩ impedance, 20-MHz bandwidth, AC coupling, 1-µs / division horizontal
resolution, 20-mV / division vertical resolution. Test points TP7 and TP9 measure the output
ripple voltage by placing the oscilloscope probe tip through TP7 and holding the ground barrel
on TP9 as shown in Figure 5-1. Using a leaded ground connection can induce additional noise
due to the large ground loop.
Voltage Source The input voltage source VIN must be a 0 to 14-V variable-DC source capable of supplying 10
ADC. Connect VIN to J1 as shown in Figure 5-2.
Multimeters V1: VIN at TP1 (VIN) and TP4 (GND).
V2: VOUT at TP7 (VOUT) and TP9 (GND).
Output Load The output load must an electronic constant-resistance-mode load capable of 0 to 15 ADC at
1.2 V.
T 9P
T 7P
Metal Ground Barrel
Probe Tip
Figure 5-1. Tip and Barrel Measurement for VOUT Ripple
Recommended Wire Gauge:
1. VIN to J1 (12-V input)
• The recommended wire size is 1× AWG number 14 per input connection, with the total length of wire less
than 4 feet (2 feet input, 2 feet return).
2. J3 to LOAD
• The minimum recommended wire size is 2× AWG number 14, with the total length of wire less than 4 feet
(2 feet output, 2 feet return).
Test Setup www.ti.com
4TPS53515 Step-Down Converter Evaluation Module User's Guide SLUUAS1C – OCTOBER 2013 – REVISED NOVEMBER 2021
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated

5.2 Recommended Test Setup
Figure 5-2. TPS53515EVM-587 Top Layer for Test Setup
Input Connections:
1. Prior to connecting the DC input-source, VIN, TI recommends to limit the source current from VIN to 10 A
maximum. Ensure that VIN is initially set to 0 V and connected as shown in Figure 5-2.
2. Connect the voltmeter V1 at TP1 (VIN) and TP4 (GND) to measure the input voltage.
Output Connections:
1. Connect the load to J3 and set the load to constant-resistance-mode to sink 0 ADC before VIN is applied.
2. Connect the voltmeter V2 at TP7 (VOUT) and TP9 (GND) to measure the output voltage.
www.ti.com Test Setup
SLUUAS1C – OCTOBER 2013 – REVISED NOVEMBER 2021
Submit Document Feedback
TPS53515 Step-Down Converter Evaluation Module User's Guide 5
Copyright © 2021 Texas Instruments Incorporated

6 Configurations
All Jumper selections must be made prior to applying power to the EVM. Configure this EVM using the following
configuration selections.
6.1 Switching Frequency Selection
Switching frequency can be changed as shown in Table 6-1.
Table 6-1. Switching Frequency Selection
SWITCHING
FREQUENCY(1)
(ƒSW) (kHz)
RESISTOR DIVIDER RATIO
(RDR)
EXAMPLE RF FREQUENCY
COMBINATIONS
RRF_H (kΩ) RRF_L (kΩ)
1000 > 0.557 1 300
850 0.461 180 154
750 0.375 200 120
600 0.297 249 105
500 0.229 240 71.5
400 0.16 249 47.5
300 0.096 255 27
200 < 0.041 270 11.5
(1) Default Setting: 1 MHz.
For different switching frequency setting, please change R3 and R4 as shown in Table 6-1.
6.2 Mode Selection
The MODE can be set by J5.
Table 6-2. Mode Selection
JUMPER SET TO: MODE SELECTION
1 to 2 pin shorted FCCM with 2x RC time constant
3 to 4 pin shorted(1) FCCM(2) with 1x RC time constant(1)
5 to 6 pin shorted FCCM(2) with 2x RC time constant
7 to 8 pin shorted Auto-skip mode with 2× RC time constant
9 to 10 pin shorted Auto-skip mode with 1× RC time constant
(1) Default setting.
(2) The device enters FCCM after PGOOD goes high.
6.3 VDD Pin Supply Selection
The controller can be enabled and disabled by J7.
Table 6-3. Enable Selection
SET ON CONNECTION ENABLE SELECTION
R19 = 0 Ω(1) VDD pin connected to VIN pins(1)
R19 = Open VDD pin disconnected to VIN pins
(1) Default setting: the VDD pin connected to the VIN pins through R19.
For power-up, input J7 with proper voltage. The VDD pin input voltage range is from 4.5 V to 25 V.
Configurations www.ti.com
6TPS53515 Step-Down Converter Evaluation Module User's Guide SLUUAS1C – OCTOBER 2013 – REVISED NOVEMBER 2021
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated

7 Test Procedure
7.1 Line and Load Regulation and Efficiency Measurement Procedure
1. Set up the EVM as described in Section 5 and Figure 5-2.
2. Ensure the load is set to constant-resistance mode and to sink at 0 ADC.
3. Ensure all jumper setting are configured as shown in Section 6.
4. Ensure the jumper provided in the EVM shorts on J2 before VIN is applied.
5. Increase VIN from 0 to 12 V. Use V1 to measure input voltage.
6. Remove the jumper on J2 to enable the controller.
7. Use V2 to measure the VOUT voltage.
8. Vary the load from 0 to 10 ADC, VOUT must remain in load regulation.
9. Vary VIN from 8 to 14 V, VOUT must remain in line regulation.
10. To disable the converter, place the jumper on J2.
11. Decrease the load to 0 A
12. Decrease VIN to 0 V.
7.2 Control-Loop Gain and Phase-Measurement Procedure
The TPS53515EVM-PWR587 contains a 10-Ω series resistor in the feedback loop for loop response analysis.
1. Set up the EVM as described in Section 5 and Figure 5-2.
2. Connect the isolation transformer to the test points marked TP5 and TP8.
3. Connect the input-signal amplitude-measurement probe (channel A) to TP10. Connect the output-signal
amplitude-measurement probe (channel B) to TP11.
4. Connect the ground lead of channel A and channel B to TP15.
5. Inject around 20 mV or less signal through the isolation transformer.
6. To measure control-loop gain and phase margin, change the frequency from 100 Hz to 1 MHz using a 10-Hz
or less post filter.
7. Disconnect the isolation transformer from the bode-plot test points before making other measurements.
• Signal injection into feedback can interfere with the accuracy of other measurements.
www.ti.com Test Procedure
SLUUAS1C – OCTOBER 2013 – REVISED NOVEMBER 2021
Submit Document Feedback
TPS53515 Step-Down Converter Evaluation Module User's Guide 7
Copyright © 2021 Texas Instruments Incorporated

7.3 List of Test Points
Table 7-1. Test Point Functions
TEST POINTS NAME DESCRIPTION
TP1 VIN Converter input supply voltage
TP2 VREG LDO voltage
TP3 PGOOD Power good output
TP4 PGND Power ground
TP5 CHB Input B for loop injection
TP6 SW Switch Node
TP7 VOUT VOUT terminal +
TP8 CHA Input A for loop injection
TP9 PGND Power ground
TP10 RF RF pin
TP11 TRIP TRIP pin
TP12 EN Enable pin
TP13 VDD VDD pin
TP14 MODE MODE pin
TP15 AGND Analog ground
7.4 Equipment Shutdown
Follow these steps when shutting down the equipment.
1. Shut down load
2. Shut down VIN
Test Procedure www.ti.com
8TPS53515 Step-Down Converter Evaluation Module User's Guide SLUUAS1C – OCTOBER 2013 – REVISED NOVEMBER 2021
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated

8 EVM Assembly Drawing and PCB Layout
The following figures show the design of the TPS53515EVM-PWR587 printed circuit board (see Figure 8-1,
Figure 8-2, Figure 8-3, Figure 8-4, Figure 8-5, Figure 8-6, Figure 8-7, and Figure 8-8). The EVM has been
designed using a six-layer, 2-oz copper-circuit board.
Figure 8-1. TPS53515EVM-587 Top-Layer Assembly Drawing
Figure 8-2. TPS53515EVM-587 Bottom-Layer Assembly Drawing
www.ti.com EVM Assembly Drawing and PCB Layout
SLUUAS1C – OCTOBER 2013 – REVISED NOVEMBER 2021
Submit Document Feedback
TPS53515 Step-Down Converter Evaluation Module User's Guide 9
Copyright © 2021 Texas Instruments Incorporated

Figure 8-3. TPS53515EVM-587 Top Layer, Copper
Figure 8-4. TPS53515EVM-587 Layer Two, Copper
EVM Assembly Drawing and PCB Layout www.ti.com
10 TPS53515 Step-Down Converter Evaluation Module User's Guide SLUUAS1C – OCTOBER 2013 – REVISED NOVEMBER 2021
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated