Texi CINQUE 35 N PREMIUM EX User manual

Safety Instruction
1. Users are required to read the operation manual completely and carefully before installation or
operation.
2. All the instruction marked with sign must be observed or executed; otherwise, bodily
injuries might occur.
3. The product should be installed and pre-operated by well-trained persons.
4. For perfect operation and safety, it is prohibited that using extension cable with multi-outlet for
power connection.
5. When connecting power supply cords to power sources, it is necessary to make sure that the
power voltage matches the rated voltage indicated on the motor’s name plate.
6. Don＇t operate in direct sun light，outdoors area and where the room temperature is over 45°C or
below 5°C.
7. Please avoid operating near the heater at dew area or at the humidity below 30% or above 95%.
8. Don＇t operate in area with heavy dust, corrosive substance or volatile gas.
9. Avoid power cord being applied by heavy objects or excessive force, or over bend.
10. The earth wire of power cord must be connected to the system ground of the production plant by
proper size of conductions and terminals. This connection should be fixed permanently.
11. All the moving portions must be prevented to be exposed by the parts provided.
12. Turing on the machine in the first time, operate the sewing machine at low speed and check the
correct rotation direction.
13. Turn off the power before the following operation：
a) Connecting or disconnecting any connectors on the control box or motor.
b) Threading needle.
c) Raising the machine head.
d) Repairing or doing any mechanical adjustment.
e) Machines idling.
14. Repairs and high level maintenance work should only be carried out by electronic technicians
with appropriate training.
15. All the spare parts for repair must be provided or approved by the manufacturer.
16. Don’t use any objects or force to hit or ram the product.
Guarantee Time
Warranty period of this product is 1 year dated from purchasing, or within 2 years from
ex-factory date.
Warranty Detail:
Any trouble found within warranty period under normal operation, it will be repaired free of
charge. However, maintenance cost will be charged in the following cases even if within
warranty period:
1. Inappropriate use, including: wrong connecting high voltage, wrong application,
disassemble, repair, modification by incompetent personnel, or operation without the precaution,
or operation out of its specification range, or inserting other objects or liquids into the product.
2. Damage by fire, Earth quake, lighting, wind, flood, salt corrosive, moisture, abnormal
power voltage and any other damage cause by the natural disaster or by the inappropriate
environments.
3. Dropping after purchasing or damage in transportation by customer himself or by
customer’s shipping agency
Note: We make our best effort to test and manufacture the product for assuring the quality.
However, it is possible that this product can be damaged due to external magnetic interference
and electronic static or noise or unstable power source more than expected; therefore the
grounding system of operate area must guarantee the good earth and it’s also recommended to
install a failsafe device. (Such as residual current breaker)

1 Key Description
Name
Key
Indicate
Function Parameter
Edit
Press this key to enter or exit function parameter edit mode.
Setting Parameter
Check and Save
For the content of the selected parameters check and save: after select parameter press
this key to check and modify operation, after modified parameter value press this key
to exit and save the parameter.
On the Adjustment
Key
1. Choose the region parameter items of incrementing key
2. Parameter setting value incrementing key
Under the
Adjustment Key
1. Choose the region parameter items of diminishing key
2. Parameter setting value decrementing key
LED Brightness
Adjustment
If click, it can adjust LED brightness.
Select the Shortcut
Needle Position
If click, the needle stop position after shift the sewing mode (Up position / Down
position).
Restore Factory
RESET
On the boot screen, long-press 3s can restore factory setting.
2 Operating Instructions
2.1 Reset the System
1. Under the shutdown state, hold on the “up” key and “down” key to boot, then double-click the S key to
confirm it, shutdown restart.
2. On the boot screen, long-press “RESET” 3s can restore factory setting.
2.2 Enter the User Argument and Save Changes
1. Under normal mode, press key P enter to【Use Parameter Area】
2. Press S key enter to parameter content value; changed the value through “up” “down” key
2.3 Enter Technician Mode and Save Changes
1. In the shutdown state, hold on key P to turn on machine and enter 【Technical Parameter Area】
2. Press S key enter to parameter content value, changed the value through “up” “down” key, and then press S
key to save the value.
3 User Parameter
Parameters
Parameter Function
Range
Default
Description
P01
Maximum speed
200-5500
5000
Set the max sewing speed.
P02
Needle stop position
selection
0-2
0
0: Needle up 1: Needle down 2: OFF
P03
Soft start switch
0-1
0
0: OFF 1: ON
P04
Soft start sewing speed
200-1500
400
P05
Stitches number of soft
start
1-15
1
P06
Minimum speed
200-500
200
Set the minimum speed
P07
Up position adjustment
0-23
P08
Down position
adjustment
0-23
P09
Needle goes up
automatically as power
turned on
0-1
1
0: No Function
1: Power turned on, needle goes up position automatically
P11
Speed curve adjustment
(%)
1-100
32
The lager the value, the faster to increase speed
P16
Machine head lamp
brightness
0-4
4
0: OFF
1→4: The brightness grade, the more value the more

Parameters
Parameter Function
Range
Default
Description
brightness.
P21
Motor rotate direction
0
0: clockwise
P22
Auto running speed
200-5000
3500
Auto running speed setting
P23
Auto running time
1-250
20
P24
Auto running stop time
1-250
20
P25
Item A test
0-1
0
Continue running with constant speed
P26
Item B test
0-1
0
Carry out the set loop running
P29
Suction function
selection
0-2
1
0: OFF
1: ON
2: Half anti-pedaling pneumatic foot lift presser function
P36
Type
1-15
P40
Information display
N01 The control system version number
N03 Speed
N04 The pedal AD
Note: the initial value of parameters is for reference only, and the actual value of parameters is subject to the real
object.
4 Error Code List
Error Code
Problem description
Measure
E01
Over-voltage
Turn off the machine, check the power supply voltage. (Or whether exceed
the rated voltage of use).
If there are still errors, please replace the control box and call for customer
service.
E02
Low-voltage
Turn off the machine, check the power supply voltage. (Or whether under
the rated voltage of use).
If there are still errors, please replace the control box and call for customer
service.
E05
Pedal connection error
Turn off the machine, please check if the pedal in bad connection or is too
loose. To get it right and turn on. If there are still errors, please replace the
control box and call for customer service.
E07
Motor locked-rotor error
Turn the machine handwheel, check if it is stuck. If it is stuck, you have to
rule out the mechanical failure.
If turn normal, check if the encoder and motor in bad connection or is too
loose. If yes, please correct.
If connection well, check if the power supply voltage is abnormal or
sewing speed is too high. If yes, please adjust.
If there are still errors, please replace the control box and call for customer
service.
E09
E11
Positioning signal error
Turn off the machine, please check if the encoder in bad connection or is
too loose. To get it right and turn on. If there are still errors, please replace
the control box and call for customer service.
E14
Encoder error
Turn off the machine, please check if the encoder in bad connection or is
too loose. To get it right and turn on. If there are still errors, please replace
the control box and call for customer service.
E15
Power supply module abnormal
over-current
Turn off the machine, then turn on again. If there are still errors, please
replace the control box and call for customer service.
5 Schematic Diagram of Port
5.1 Each Port Name

12
LED Lamp: 1(GND), 2(+5V)