Theben theLeda D B AL User manual

1
theLeda D B AL
1020905
theLeda D B plus AL
1020906
theLeda D B plus S AL
1020907
theLeda D BL AL
1020705
theLeda D BL plus AL
1020706
307399 02
Bollard lamp with/without
motion detector
EN
1. Basic safety information
LThe bollard lamps with and without motion detector
(PIR), as well as with power outlet are in accordance with
EN 60598-1.
2. Proper use
•Device is intended for mounting outdoors
•At paths, drives of single-family houses, hotel entrances,
medical practices etc.
•For use in normal ambient conditions
•The bollard lamp is used for lighting, depending on pre-
sence and brightness
•Operable with theSenda S remote control, adjustable
with theSenda P and theSenda B with theSenda Plug app
LLamp cannot be replaced.
Replace entire lamp if defective!
Disposal
Dispose of bollard lamp properly (electronic waste)
3. Connection and installation
Danger of death through electric shock or fire!
Installation should only be carried out by a
quali ed electrician!
WARNING
Disconnect power source!
Ensure device cannot be switched on!
Check absence of voltage!
Earth and bypass!
Cover or shield any adjacent live components.
N
L
N L
*
*at 1020907
Installation on concrete fl oor
LThe base plate is supplied without screws
Installation on grass fl oor
0FF
230V
LOptional with ground spike (9070765)
!Use RCCB
Disconnect power source
For mounting on solid ground, screw on the base plate; for
mounting on soft ground, use the ground spike (9070765)
and attach the base plate on top of it
Take off the cover of the junction box and connect the indi-
vidual wires to the appropriate terminal
Put the cover on the junction box and plug the bollard lamp
over the junction box

2
Washer
Screw the bollard lamp on the base plate and connect to
the mains
LThe device needs approx. 40 s of preheating time.
Detection area
6 m
5 m
4. Description
2 potentiometers
Base plate
Junction box
Bollard lamp
LThe bollard lamp has 2 potentiometers for setting the time
(TIME) and brightness (LUX).
5. Setting
Using the grouping function (setting the wireless
channel)
LThe bollard lamps can be set and operated in a wireless
network. Any number of devices with and without motion
detector can be operated on one wireless channel.
LThe grouping function can be activated with theSenda
Plug app and theSenda B remote control (parameter→
RF channel)
LOn bollard lamps without motion detector, the wireless
channel must be selected via theSenda B remote control
and theSenda Plug app for wireless networking.
LFor settings that can be made with the app and on the
device, the last set value is always saved.
Setting the brightness (LUX)
Turn the potentiometer to "Teach-In "; after 15 s, the
motion detector saves the current surrounding brightness
as the new switch-on brightness
Set the potentiometer to the desired brightness (2 –
800 lux/∞)
On the ∞ setting, the lamp responds to motion, regardless
of the brightness
Setting the time (TIME)
Set the potentiometer to the desired time (10 s – 20 min)
Turn the potentiometer to "D" (dimming function); the
motion detector only responds to brightness and is always
switched on when the set brightness value has not been
reached → the bollard lamp is switched on during dark-
ness (motion detector is disabled)

3
6. Walking test
The walking test is used to test the detection area and to
restrict it if necessary.
Set the time potentiometer (TIME) to "test"
▻The motion detector now always responds to
movements (independent of brightness).
Walk across the detection area. After the motion detector
has detected a movement, it switches on for 2 s. The test
mode is quit again after 10 min.
LIf you walk diagonally to the motion detector, the detec-
tion is more sensitive than with a direction of movement
directly towards the motion detector.
LThe function can be quit with any other function
command.
LThe walking test can also be activated in the app (control
commands → presence test), or with theSenda P.
7. Limiting the detection area
Use the enclosed stickers to adjust the motion detector to
the desired detection area
Remove the required section of the sticker by using scissors
Then stick it to the lens
8. Settings and functions
LFor an optimum setting of the functions we recommend
theSenda B remote control with theSenda B Plug app.
theSenda B remote control with theSenda B Plug app.
LWith each setting, the device con rms the received com-
mand with a  ashing (2 x) of the light.
LIf you combine theSenda B remote control with theSenda
Plug app, the terms "control commands" and "parame-
ters" appear in the app.
Parameter Control commands
Brightness setpoint value Teach-in
Time delay Switching light
Maximum brightness Presence test
Standby dimming value Detection sensitivity
Scene 1 Night switch-off
Scene 2 Standby
RF channel Presence simulation
D mode
Auto
LAuto (normal operation), scene 1, scene 2, D mode,
presence simulation and presence test are states of the
device. A combination of these states is not possible.
Auto mode (normal operation)
The standard settings include time delay, brightness setpoint,
maximum brightness and sensitivity of the motion detector.
24
12 12
Movement
LED-Light
100 %
Night
Lux
LThe LED lamp is switched on if there is movement and the
brightness has fallen below the setpoint.
Press button A (Auto) on theSenda P, S, or B remote control
There are 3 ways to select the brightness setpoint and the
lighting time delay:
– selection with the app → under parameter → lighting
time delay select etc.
– with theSenda P
– or with the potentiometers at the device
LThe brightness of the lamp can be dimmed via the "maxi-
mum brightness" parameter.

4
In auto mode, various additional functions can be activated:
orientation light, switching on/off and setting the intensity
(10-40%).
Orientation light (= standby dimming value)
The orientation light provides a de ned basic brightness of
10 to 40% so that pathways, access routes and entrances are
dimly lit after nightfall. If the device registers a movement, the
LED lamp will light up 100% and dims down again to the set
brightness value after the preset time delay.
24
12 12
30 %
Lux
Movement
LED-Light
100 %
Night
LIf the brightness falls below the setpoint, the lamp swit-
ches on a reduced orientation light even without move-
ment. When motion is detected, the light is switched to
maximum brightness.
LSetting only via theSenda B remote control and the app
(always 10% – 40%).
theSenda Plug app
under parameters → select standby dimming value, and
send
back to → control commands → select standby, and send
▻ Detector  ashes 2 x → standby dimming value is on
Self-learning night switch-off
The self-learning night switch-off adjusts to the changing
twilight times and switches off for 4 hours in the 2nd half
of the night when orientation/standby light is activated. If
motion is detected during this switch-off, the light is switched
to maximum brightness.
24
12 12
30 %
Lux
Movement
LED-Light
100 %
Night
Night break
LThe night switch-off does not in uence the motion-trig-
gered light switching!
LSetting only via theSenda B remote control and theSenda
Plug app.
theSenda Plug app
Control commands → select night switch-off, and send
Dimming function (= D mode)
The dimming function of the LED lamp ensures that the
light is switched on at maximum brightness as soon as the
brightness falls below a certain value - regardless of whether
the device registers a movement or not. The light is switched
on again when suf cient daylight is available.
24
12 12
Lux
D-mode
Movement
LED-Light
100 %
Night
LAdditional night switch-off function: switching on and
off; function determines midpoint between twilight and
switches off the light for 4 hours from the 2nd half of the
night; function does not in uence motion-triggered light
switching!
Press button D (D mode) on theSenda P, S, or B remote
control
or select → control commands → D mode in the app
▻D mode is on
Press key A or send Auto command in the app to exit the
function
Light function on/off
Light function on
•The light is switched on with the maximum brightness
•Automatic change to auto mode after 8 hours
•Exiting the function with any other function command
Light function off
•The device switches off, the motion detector no longer
responds
•Automatic change to auto mode after 8 hours
•Exiting the function with any other function command
Entering and calling up lighting scenarios
LAutomatic change to auto mode after 8 hours
LExiting the function with any other function command
In the app → parameters → select value for lighting
scenario 1 (default 33%), or lighting scenario 2 (default
66%), and send; or
set the desired value via dimming with theSenda B or
theSenda S
Hold down the button for lighting scenarios
▻ Detector  ashes 2 x and lighting scenario is saved
Calling up lighting scenario
With theSenda B, press the button for lighting scenario 1 x
brie y
▻Lighting scenario is active for 8 hours
Press button A, to prematurely  nish the function

5
Holiday mode (presence simulation)
LThe holiday mode always has a time delay of 2 min. and
changes the setpoint. If the mode is exited via the button
or command A (Auto), the desired time delay has to be set
again.
In the app → control commands → select presence simu-
lation, and send
or press the "holiday mode" button with theSenda B or
theSenda S
Manual operation
The lighting can be switched on manually via a circuit breaker
button.
LA circuit breaker button must be connected.
N
L
N L
Press the circuit breaker button briey (max. 1.5 s).
▻The lighting will come on for the set time.
Press the circuit breaker button 2 x briey (within 1.5 s).
▻The lighting remains switched on for 6 hours (perma-
nent light).
In order to switch off the lighting, press the circuit breaker
button 1 x briey (max. 1.5 s).
▻The detector switches off after the set time delay.
LIf the circuit breaker button is pressed longer than 2 s, the
detector restarts (warm-up phase).
9. Settings with remote control
LYou can enter the settings with the remote controls the-
Senda S, theSenda P, and theSenda B.
LAll settings can be quit by pressing button A.
Settings using theSenda P (9070910)
The following parameters or functions can be set with
theSenda P:
31 1
2
6
8
9
10
11
12
13
14
15
23
22
21
20
18
17
16
26
25
24
30
7
1Test Test mode, ends after 10 min
2Auto return to Automatic mode
6On Switch on light*
7Range + Increase sensitivity
815 lux Brightness setpoint value 15 lux
910 lux Brightness setpoint value 10 lux
10 Lux On Deactivation of brightness measurement
11 800 lux Brightness setpoint value 800 lux
12 60 s Lighting time delay 60 s
13 30 s Lighting time delay 30 s
14 max. Time max. lighting time delay, 20 min
15 20 min Lighting time delay 20 min
16 10 min Lighting time delay 10 min
17 2 min Lighting time delay 2 min
18 min. Time min. lighting time delay, 10 s
20 500 lux Brightness setpoint value 500 lux
21 300 lux Brightness setpoint value 300 lux
22 5 lux Brightness setpoint value 5 lux
23 min. lux min. brightness setpoint value, 1 lux
24 Range – Reduce sensitivity
25 Teach-in Teaching in the brightness setpoint value
26 Off Switch off light*
30 Reset Restart of the detector
31 D mode Dimming function (motion detector deactivated)
* active for 8 hours
LBy pressing the reset button on theSenda P or in the app,
it will be reset to the default values (2 min, 15 lux).

6
Settings using theSenda S (9070911)
6
4
2
5
7
8
9
1
3
1D mode Twilight switch (motion detector deactivated)
2 4 Off short button push → switches off the light*
long button push → dimming the light down*
3 5 On short button push → switches on the light*
long button push → dimming the light up*
6Auto return to Automatic mode
7Holiday mode Presence simulation
8Lighting
scenario 1
Pressing the button shortly → the dimming
value of 33% is set*
9Lighting
scenario 2
Pressing the button shortly → the dimming
value of 66% is set*
* active for 8 hours
Holiday mode
The holiday mode is a presence simulation, which is used to
prevent burglary during temporary absence.
Settings by using theSenda B (9070985)






LED
14
13
12
11
LIf you would like to use the settings of the remote control
for the presence detector (default) also for the outdoor
detectors,
press buttons 8 + 9 > 5 s.
1Bluetooth Connection/pairing
3On Short button press → channel light on*
Long button press → channel light dims up*
6OFF
Short button press → channel light off*
Long button press → channel light dims
down*
10 Lighting
scenario 1
Short button press → call up lighting scenario
1*
Press button > 3 s → program lighting scena-
rio 1*
8Lighting
scenario 2
Short button press → call up lighting scenario
2*
Press button > 3 s → program lighting scena-
rio 2*
9Auto Return to auto mode
14 Holiday mode Presence simulation
11 Night off Night switch-off from approx. midnight to
04:00 a.m.
13 D mode Dimming function
12
Standby Short button press → activate basic brightness
in darkness
Max.
brightness
Press button > 3 s → save current brightness
as max. brightness value
* active for 8 hours
10. Technical data
Operating voltage: 230 V AC, + 10%/– 15%
Frequency: 50–60 Hz
Consumption with light On: 8.5 W
Standby output: max. 0.5 W (with detector)
LED output (luminous ux): 760 lm
Colour temperature: 3000 K
Colour rendering index: CRI > 80
Service life: L80/B10/50,000 h
Protection rating: IP 55 in accordance with EN
60529
Protection class: II in accordance with EN 60598-1
Operating temperature: –25 °C … +45 °C
Brightness setting range: 2 – 800 lux /∞
Duty cycle range: 10 s – 20 min
Detection angle: 180°
RF range: 100 m on open air test site (max.
20 devices per channel)
Detection area: lateral:
frontal:
max. 6 m
max. 5 m
Energy efciency class: A+
Height of light source: 364 mm (1020705); 684 mm
(1020706)
Torque of xing screws: 5.1 Nm
Power outlet device (1020907): 230 V AC/16 A (3680 W); IP 54;
protection class I in accordance
with EN 60598-1
Theben AG herewith declares that this type of radio installation
complies with Directive 2014/53/EU. The complete text of the
EU Declaration of Conformity is available at the following Internet
address: www.theben.de/red-konformitaet

7
35,7
104,3
7
32,2260
400,5
174
126
42 90
32,2580 104,3
7 35,7
720,5
174
126
42 90
1020705
1020905
1020706
1020906 11. Contact
Theben AG
Hohenbergstr. 32
72401 Haigerloch
GERMANY
Phone [phone]
Fax [phone]
Hotline
Phone [phone]
[email protected]
Addresses, telephone numbers, etc.
www.theben.de

8