Theben thePrema S360-100 E UP WH User manual

1
thePrema S360-100 E UP WH
2070600
thePrema S360-100 E UP GR
2070601
307184
1103087901
Presence detector
EN
1. Product characteristics
•Passive infrared presence detector for ceiling installation
•Square detection area 360° (up to 64 m2) for reliable and
easy planning
•Automatic presence- and brightness-dependent control for
lighting and HVAC
•Mixed light measurement suitable for uorescent lamps
(FL/PL/ESL), halogen/incandescent lamps and LEDs
•Channel A light: relay, 230 V
•Fully or semi-automatic operation, switchable
•Brightness switching value congurable, teach-in function
•Self-learning time delay
•Reduction of time delay when present briey (short-term
presence)
•Connection option for push buttons or switches for manual
switching with automatic detection of «push button/
switch»
•Pulse function for staircase light timer switch
•Ready for immediate use due to factory presetting
•Exceptionally easy conguration of the energy-saving res-
ponse with the new «eco plus» function
•Test mode for checking function and detection area
•Extension of detection area via master/slave or master/
master switching, a maximum of 10 detectors can be swit-
ched in parallel with each other
•Ceiling installation in ush-mounted box
•Surface mounting on ceilings possible with back box
(option)
•User remote control «theSenda S» (option)
•Management remote control «SendoPro» (option)
•Installation remote control «theSenda P» (option)
2. Safety
Danger of death through electric shock or fire!
Installation should only be carried out by a quali-
fied electrician!
WARNING
•Work on electrical systems may only be carried out by
qualied electricians or by instructed persons under the
guidance and supervision of a qualied electrician in
accordance with the technical regulations applying to
electricity!
•Comply with the country-specic safety regulations for
work on electrical systems! Ensure absence of voltage in
the cable before installation!
•The device is maintenance-free. If the device is opened
or penetrated with any object, the guarantee lapses.
3. Proper use
The presence detector is intended for interior installation. The
presence detector is exclusively intended for the use as cont-
ractually agreed between the manufacturer and the user. Any
other use is considered to be unacceptable. The manufacturer
does not accept liability for any resulting damages.
4. Operation
The presence detector is primarily used in ofces and schools,
as well as in homes, for easy and energy-efcient control
of lighting and shading. The switch contact "light" switches
lighting on with presence and insufcient brightness, and off
with absence or sufcient brightness. The light can also be
switched on/off manually using buttons or switches.
Function description






Mixed light measurement
Presence detection
 Articial light
Push button for manual lighting control
Incident daylight

2
E


 
Settings on thePrema S360-100 E
Brightness setpoint value (lux)
Lighting time delay
DIP-Switch:
DIP1 Fully automatic/semi-automatic
DIP2 Staircase light function:
room/corridor
DIP3 eco/eco plus
DIP4 Short-term presence On/Off
DIP5 Light test: normal operation/test
DIP6 Presence test: normal operation/
Walking test
Mechanical safety lock
Light channel A
Switching response is controlled by presence and bright-
ness. The switch contact closes during darkness and when
someone is present. It opens with a delay when there is
brightness or when no one is present.
Time delay
The minimum time delay (10 s - 60 min) is adjustable.
It adjusts automatically to the user's behaviour and can
increase independently to max. 30 minutes or reduce back to
the set minimum time. With settings ≤ 2 min or ≥ 30 min, the
time delay remains unchanged at the set value. If someone
goes into an unoccupied room only briey and leaves it within
30 seconds, then the light will be switched off prematurely
after 2 minutes (short-term presence).
Button control
The lighting can be manually switched at any time via a push
button or switch. If the light is switched on manually, it will
remain on for at least 30 minutes provided that people are
present. It then switches off when the brightness is adequate.
The light is forced off after the preset time delay if the room
was (previously) vacated. If articial lighting is switched off
manually, the lighting remains switched off as long as the
room is occupied. The lighting switches again automatically
after the time delay has expired.
Fully or semi-automatic device
Lighting control via the presence detector operates fully
automatically for increased comfort or semi-automatically for
greater energy savings. The lighting switches on and off auto-
matically in "fully automatic" mode. In "semi-automatic", the
lighting must always be switched on manually. The lighting is
switched off automatically.
Staircase light function
The staircase light function can be set to "room" or "corridor"
using the DIP switch or the SendoPro management remote
control. Lighting can be switched on and off manually at any
time in the 'room' position. The detector operates as a stair-
case light control in the 'corridor' setting. Manual switch off is
no longer possible.
Exceptionally easy conguration of the energy-saving
behaviour
By selecting “eco” for optimal switching behaviour or “eco
plus” for maximum energy saving, users can adjust the pre-
sence detector to their requirements very easily.
Pulse function
Time delay can be set to pulse for controlling existing stair-
case light timer switch. To do so, the light output produces a
pulse of 0.5 seconds duration every 10 seconds if people are
present or it is dark.
5. Detection area
The square detection area of the presence detector guaran-
tees accurate and simple planning. Square detection areas
make it possible to cover a whole room with parallel swit-
ching. Note that seated and walking persons are detected in
differently-sized areas. The recommended installation height
is 2.0 m – 3.0 m. The sensitivity of the presence detector
decreases with higher installation heights. At an installation
height of 3 m or higher, walking motions are necessary and
the detection areas of several detectors should overlap in the
marginal zones. The detection range is reduced as temperatu-
res increase.
Seated persons:
The presence detector reacts very sensitively to the slightest
movements. The details refer to smallest movements at table
height (approx. 0.80 m). The detection sensitivity is reduced
from an installation height of > 3 m. More pronounced
movements are required for clear detection.
Walking persons:
Use of the whole detection area.

3
o
01
23
414
23
3
2
1
0
m
seated persons
walking persons
Installation
height
seated persons walking persons
2.0 m 9 m23.0 m x 3.0 m 20 m24.5 m x 4.5 m ± 0.5 m
2.5 m 16 m24.0 m x 4.0 m 36 m26.0 m x 6.0 m ± 0.5 m
3.0 m 25 m25.0 m x 5.0 m 49 m27.0 m x 7.0 m ± 1.0 m
3.5 m --- 64 m28.0 m x 8.0 m ± 1.0 m
Brightness measurement
The presence detector measures articial light and daylight
(opening angle for each approx. ± 30°). The installation loca-
tion is the reference point for the lighting level. The bright-
ness measurement can be adapted to the conditions in a
room with the room correction factor. The light measurement
area maps a rectangle of about 2 x 3.5 m at table height.
Direct light inuences the light measurement. Avoid placing
oor lamps or suspended lighting directly below the detector.
If the brightness measurement is deactivated, light channel A
only switches depending on presence (brightness switching
value set to "on" via potentiometer or set to "measurement
off" via the remote control).
FensterInnen 2m
Suitable lamps
The presence detector is designed for the operation of uore-
scent lamps, compact uorescent lamps, halogen/incande-
scent lamps and LEDs. The maximum number of switchable
lights is restricted due to the high inrush current levels of the
EBs and LED drivers. The use of an external contactor helps
with large loads. Parallel switching enables allocation of load
to several Masters. All switched loads must be properly inter-
ference suppressed.
6. Installation
Flush-mounted tting
The presence detector is ush-mounted using a size 1 stan-
dard ush-mounting installation socket.
Ceiling installation
A ceiling installation box 73A is available for a simplied
ceiling installation of the presence detector (see accessories).
This also ensures cord grip and contact protection. The instal-
lation diameter is 72 mm (drill diameter 73 mm).
Surface-mounted installation
A back box 110A, protection rating IP 40, is available for sur-
face mounted installation (see accessories).

4
7. Connection
The presence detectors can be combined as master and slave:
master in individual switching, master in parallel switching,
master-slave parallel switching.
Several push buttons can connected to one control input.
Illuminated push buttons can only be used with neutral con-
ductor connection.
Individual switching
In individual switching, the presence detector as master
detects presence and brightness and controls lighting.
L’
Master/slave parallel switching
If the detection area covered by one presence detector is
insufcient (larger rooms), then up to 10 detectors can be
operated in parallel by connecting P terminals. In the process,
presence detection is performed by all detectors together. The
master measures the brightness, operates the push buttons
and controls the lighting. All other detectors are used as
slaves. They only provide presence information.
Master Slave
L’
•Light measurement only with the master
•Parameters are only set on the master
•Switch up to 10 detectors in parallel
•Use the phase with the same phase for all detectors.
Master: thePrema S360 -100 E
Slave: thePrema P360 Slave E, thePrema S360 Slave E
Master/master parallel switching (for several
lighting groups)
Several masters can be used in parallel switching setup. Each
master controls its lighting group according to its own bright-
ness measurements. Delay times and brightness switching
values are set individually on each master. Presence continues
to be detected by all the detectors.
Master 1 Master 2
L’
L’
•One master with individual brightness measurement per
lighting group
•Set potentiometer and DIP switch individually for each
master
•Switch up to 10 detectors in parallel.
•Use the phase with the same phase for all detectors.
Parallel switching on external staircase light
timer switch
One or several presence detectors control a staircase light
timer switch as master. Their time delay is set to short pulse.
When people are present and there is insufcient brightness,
their switch contacts close every 10 seconds for a period of
0.5 seconds and thus restart the time delay of the staircase
light timer switch.

5
•Switch light switch contacts of several detectors directly
in parallel.
•Set light time delay in all detectors to short pulse.
•Use the phase conductor with the same phase for all
detectors.
•Staircase light timer switch, e.g. Theben ELPA 1
34 L’ L’
Presence detectors as a staircase light timer
switch
As master, a presence detector assumes the function of the
staircase light timer switch. At the master, the DIP switch
is set to "corridor". With every detected movement or push
button activation, the time delay is restarted. However, the
lighting cannot be switched off with the push button. If the
detection area covered by one presence detector is insuf-
cient (larger rooms), then up to 10 presence detectors can be
operated in parallel as slaves by connecting P terminals.
•Master switches lighting directly.
•Push button starts the time delay of the master.
•DIP switch to "corridor" prevents switching off with the
push button.
•If needed, switch additional slaves in parallel via P
terminals.
•Use the phase with the same phase for all detectors.
•Potentiometers and DIP switches are only set on the
master.
N
L
L’
Master: thePrema S360 -100 E
Slave: thePrema S360 Slave E
8. Settings
The presence detectors were supplied with basic settings
ready for operation. The specications are guidance values.
Management remote controls are optionally available for
start-up. They enable remote setting of all potentiometer
values and DIP switch settings from a distance.
Settings of switch contact light channel A
Potentiometer brightness switching value "lux"
The required brightness switching value can be set via the lux
potentiometer.
The setting range is around 10 to 1000 lux. The factory pre-
setting is 300 lux.
Brightness switching values from 5 to 3000 lux can be set via
the management remote control.
According to standard EN 12464, the following settings are
recommended:
Transit zones (no work area) 150 lux
Classroom 300 lux
Work areas (ofce, meeting room) 500 lux
Visually-intensive work (laboratory, drawing, etc.) 750 lux
Brightness measurement can be deactivated. In this case,
the brightness has no inuence, and channel A light always
switches at presence/absence.
Deactivation of the brightness measurement: set the poten-
tiometer to „on“.
The lux scale applies for rooms with average room design. It
is recommended that the room correction factor be adjusted
with the management remote control according to the instal-
lation location, light incidence, reection characteristics of the
room and the furniture.
Potentiometer lighting time delay
The following guidance values have proved themselves in
practice and are recommended as settings:
•Transit zones (no work area approx. 5 min
•Classroom approx. 10 min
•Work areas (ofce, living room) approx. 10 min
•When settings are between 2 - 30 mins the time delay
varies within this range in a self-learning way.
Setting values ≤ 2 min or ≥ 30 min remain xed. Only
active with the setting "eco".
• "Pulse": Control staircase light timer switch (0.5 s "on"
/10 s "off")

6
DIP switch fully/semi-automatic (auto/man)
Description of the function semi-automatic or fully automatic,
see function description:
•"auto": fully automatic: the lighting switches on and off
automatically.
•"man": semi-automatic: switching on always has to be
completed manually. Switching off occurs automatically.
DIP switch staircase light function (room/corridor)
For description of the staircase light function, see function
description:
•"room" : manual switching on and off possible
•“corridor”: detector is used as staircase light timer
switch. Manual switch off is no longer possible
DIP switch energy saving behaviour (eco/eco plus)
Selection of “eco” for optimal switching behaviour or “eco
plus” for maximum energy saving.
•“eco”: The time delay adapts to the user behaviour in a
self-learning way.
It does not drop below the set value.
•“eco plus” : The set time delay remains unchanged (no
self-learning effect). Faster response to brightness
detection than with „eco“.
DIP switch short-term presence (On/Off)
For description of short-term presence, see function
description:
•„2 min“ short-term presence is switched on
•„ “ Short-term presence is switched off.
Parameters and control commands via remote
control
The following parameters can be queried or changed via
the remote control for support during installation as well as
servicing:
Parameters Description Can be
queried
SendoPro
868-A
Can be
changed
SendoPro
868-A
Can be
changed
theSenda
P
Brightness
switching
value A
Value range in lux x x x
Measurement off x x x
Room correc-
tion factor A
Room correction
factor x
Brightness
actual value A
Query brightness
actual value x
Time delay A
Value ranges in
seconds /minutes x x
Pulse x x
Parameters Description Can be
queried
SendoPro
868-A
Can be
changed
SendoPro
868-A
Can be
changed
theSenda
P
Short presence
A
Short-term presence:
On/Off x
Energy saving
mode
Selection: eco /eco
plus x x
Conguration
type Selection: auto / man x x x
Staircase light
function Selection: Off / On x
Control input S
Auto /switch /push
button S /push
button O
x
Detection
sensitivity
Detection
Sensitivity
(PIR): value range in
Increments
x x
Monitoring
sensitivity
reduction
Room monitoring
sensitivity: value
range in
Increments
x
Group address Selection: I /II / III
/all x
Scene 1 Off /On x
Scene 2 Off /On x
LED display
motion Off /On x
The parameters are sent to the presence detector with the
"SendoPro 868-A" management remote control or with "the-
Senda P" installation remote control via infra-red. Changed
parameters are immediately applied and used by the detector.
With the "SendoPro 868-A" management remote control,
parameters can be queried by sending values level-by-level
to the detector. If the sent value is below the set parameter,
the LED illuminates briey. If the sent value is equal or above
the set parameter, the LED ickers for 2 seconds.
The following control commands can be triggered
with the remote control:
Control
command
Description Can be
triggered
SendoPro
868-A
Can be
trigge-
red the-
Senda P
Teach-in chan-
nel A Activation x x
Switching light Lighting group can be switched
on and off. x x
Presence test Off / On x x
Light test Off /On x
Restart Restart detector x x
Local settings
Detector applies the settings
of the DIP switch and all
potentiometers
x
Factory
settings
Set all parameters and settings
to factory setting. x
Brightness switching value A
The brightness switching value denes the minimum desired
brightness. The currently prevailing brightness is measured
below the presence detector. If the prevailing brightness
is below the switching value, the light switches on when a
presence is detected (in conguration type fully automatic
device).

7
Value range
Lux values with "SendoPro 868-A" management remote
control
In the installation remote control "theSenda P", the
following values are available
(The currently measured brightness value (Lux) can
be adopted with the "SendoPro 868-A" management
remote control, with the teach-in control command or
with the “theSenda P” installation remote control via the
teach-in button.)
Values outside the permitted range will automatically be
set to the appropriate limit value.
5–3000 lux
5, 10, 15, 300,
500, 800 lux
- Deactivating the brightness measurement (the bright-
ness has no inuence)
- The light channels only switch according to presence/
absence.
Possible with "SendoPro 868-A" management remote
control or "theSenda P" installation remote control.
Measurement
off
Button
Room correction factor A
The room correction factor is a measurement for the diffe-
rence of the brightness measurement on the ceiling and the
work area. The brightness measurement value at the ceiling
is inuenced by the installation location, incidence of light,
position of the sun, weather conditions, the reection proper-
ties of the room, and the furniture.
With the room correction factor, the brightness measurement
value of lighting channel A is adjusted to the conditions in the
room and in this way can be matched to the lux meter value
measured at the surface beneath the presence detector.

Room correction factor = Brightness value at the ceiling /
brightness value at the working surface
We recommend the following procedure:
•Place the lux meter on the work surface below the sensor
and note down the measured lux value.
•Query „brightness actual value A“ with the «SendoPro
868-A» management remote control.
•Calculating the room correction factor: „brightness actual
value A“ /lux value of lux meter.
•Enter „room correction factor A“ with the «SendoPro
868-A» management remote control. Values between 0.05
and 2.0 are permitted. Entered values outside the permit-
ted range will automatically be set to the appropriate limit
value. The entered room correction factor will be applied
immediately.
!The standard value is 0.3 and is suitable for most
applications.
Changes are only sensible in strongly deviating
situations.
Time delay A
Value range
Adjustable values with "SendoPro 868-A" manage-
ment remote control
In the "theSenda P" installation remote control, the
following values are available
10 s - 60 min
10 s, 30 s, 60 s, 2
min, 10 min, 20 min,
60 min
Control for staircase light timer switch (0.5 s "on"
/10 s "off")
"SendoPro 868-A"
"theSenda P"
Pulse
Button 1
Short-term presence
The time delay of Channel A light can be switched off sooner
if a room is occupied only for a short time. (In fully automatic
device and semi-automatic device conguration type)
The time delay is applied according to the set time delay. off
If someone enters an unoccupied room and it is only occupied for
up to 30 seconds, the light will be switched off prematurely after
2 minutes.
On
Energy saving mode eco/eco plus
With the «SendoPro 868-A» management remote control, the
energy-saving behaviour can be set very simply. The selection
of “eco” stands for optimum switching behaviour, while “eco
plus” stands for maximum energy saving.
•“eco”: The time delay adapts to the user behaviour in a
self-learning way. It does not drop below the set value.
•“eco plus” : The set time delay remains unchanged (no
self-learning effect). Faster response to brightness detec-
tion than with "eco".
Conguration type
Fully automatic device: The lighting switches on and off auto-
matically. (due to presence/no presence and brightness)
auto
Semi-automatic: Switch on must always occur manually. Switch
off occurs automatically by the presence detector. (due to pre-
sence or brightness)
man
Control input S
Control input S for manual switch on/off of Channel A light
automatically detects push buttons or switches.
Several push buttons can be connected to control input S
Use light push button only with neutral conductor connector
Value range
Automatic detection of push button or switch. A signal that
is present for less than 0.7 s is detected as a push button.
Longer signals are evaluated as a switch.
auto
To adapt to user behaviour, the type
of signal transmitter used can be
set to xed. Automatic detection is
deactivated.
When selecting the push button,
opening contact or NO contact can also
be specied.
Switch
Push button (NO
contact)
Push button
(opening contact)
Switch
Push button
S
Push button
O
Adjustment possible only with "SendoPro 868-A".

8
Detection sensitivity
The detector has 5 sensitivity increments. The basic setting is
the middle increment (3).
By selecting the test presence operating mode, the set sensi-
tivity increment is not changed.
Increments 1 to 5 can be selected and sent to the detector
with the «SendoPro 868-A» management remote control.
On the «theSenda P» installation remote control, the sensi-
tivity can be increased or decreased by one increment each
time the button is pushed.
Increment Sensitivity
1 very insensitive
2 insensitive
3 Standard
4 sensitive
5 very sensitive
Room monitoring sensitivity
The detector has 3 sensitivity levels. The basic setting is the
middle increment 2.
Sensitivity increments 1 to 3 can be selected and sent to the
detector with the «SendoPro 868-A» management remote
control.
Increment Sensitivity
1 insensitive
2 Standard
3 sensitive
Group address channel A
This parameter is applied when using the "theSenda S" user
remote control.
A group address can be assigned to Channel A light.
The "SendoPro 868-A" or "theSenda S" can be used to pro-
gram the group addresses in the detector.
Group address value range
Adjustable values "SendoPro 868-A" I, II , III , All
Adjustable values "theSenda S" I, II
LED display motion
The motion detection can be displayed via the LED.
Value range
No display of motion detection. off
The LED is switched on when motion is detected, otherwise
switched off.
On
Adjustment possible only with "SendoPro 868-A".
Teach-in channel A
With teach-in, the currently measured brightness value is
accepted as brightness switching value A. Values outside the
permitted range will automatically be set to the appropriate
limit value. The control command teach-in can be adopted
with the "SendoPro 868-A" management remote control or
with the "theSenda P" installation remote control via the
button.
Factory settings
The presence detector thePrema S360-100 E is supplied with
the following parameter values:
Parameters Value
Brightness switching value A 300 Lux
Room correction factor A 0.3
Time delay A 10 min
Short presence A On
Energy saving mode eco
Conguration type auto
Staircase light function off
Control input S auto
Detection sensitivity Increment 3
Monitoring sensitivity reduction Increment 2
Group address I
Scene 1 On
Scene 2 off
LED display motion off
9. Start-up
Switch-on behaviour
Every time the sensor unit is inserted into the power supply
unit, or every time the power supply is switched on, the pre-
sence detector runs through two phases that are shown by an
LED:
1. Start-up phase (30 s)
•The red LED ashes at one second intervals, both switch
contacts are closed (light and presence on).
•The detector does not react to push button commands
and remote control commands.
•When no one is present, both contacts open after 30
seconds.
2. Operation
The detector is ready for operation (LED off).
Presence test
Presence test mode is used to test presence detection and
wiring. The presence test mode can be activated directly on
the presence detector via DIP switch, with the "SendoPro 868
A" management remote control, or "theSenda P" installation
remote control.
Setting presence test mode with DIP switch
 Set DIP switch to "Test " (in parallel switching with all
detectors).

9
1. Start-up phase (30 s)
The contact is closed for 30 seconds. Every movement is
indicated by the LED.
2. Operation
•Every movement is indicated by the LED.
•When movement occurs, the light switch contacts closes.
•When no one is present, the light switch contact opens
after 10 seconds.
•Brightness measurement deactivated, detector does not
react to brightness.
•The detector reacts as in conguration type fully auto-
matic device, even if semi-automatic is set.
•Detector stays permanently in the test phase.
Setting the presence test mode via remote control
•The detector goes directly into test mode when the test
mode is set via the remote control:
•Every movement is indicated by the LED.
•When movement occurs, the light switch contacts closes.
•When no one is present, the light switch contact opens
after 10 seconds.
•Brightness measurement deactivated, detector does not
react to brightness.
•The detector reacts as in conguration type fully auto-
matic device, even if semi-automatic is set.
•Teach-in cannot be activated in test mode.
•Test mode ends automatically after 10 min. The detector
performs a new start (see switch-on behaviour).
Light test
The light test mode is used to check the brightness threshold
and the adaptive behaviour.
Setting the light test mode via DIP switch
Set the DIP switch at the master to "Test ".
1. Start-up phase (30 s)
The contact is closed for 30 seconds. The LED shows the light
test mode (3 seconds on, 0.3 seconds off).
2. Operation
•The LED shows the light test mode (3 seconds on, 0.3
seconds off).
•The presence detector responds as in normal operating
mode, only the reaction to bright/dark is faster.
•In order to simulate this behaviour, either the area below
the presence detector can be illuminated or the blinds
operated.
•Detector stays permanently in the test phase.
•Note: Do not use a torch to switch the presence detec-
tor! The adaptive light switching thresholds will be
distorted!
Setting the light test mode via remote control
•The detector goes directly into test mode without the
start-up phase when setting the test mode with the
remote control.
•Test mode ends automatically after 10 min. The detector
performs a new start (see switch-on behaviour).
10. Technical Data
Operating voltage 110–230 V AC, +10 %/–15 %
Frequency 50–60 Hz
Upstream protection device: 16 A
Power consumption approx. 0.1 W
Type of installation Ceiling installation; Flush/
surface mounted or ceiling
installation
Installation height 2.0 – 3.5 m
Minimum height > 1.7 m
Detection area horizontal
vertical
360°
120°
Maximum range 5 x 5 m (Mh. 3.5 m) /25 m2
seated
8 x 8 m (Mh. 3.5 m) /64 m2
moving
Setting range brightness switching value approx. 5 – 3000 lux
Lighting time delay 10 s – 60 min/pulse
Channel A light Relay 230 V /10 A, µ-contact
Max. switching capacity cos ϕ1 ohmic 2300 W
Max. switching capacity cos ϕ0.5
Power factor 0.5 1150 VA
LED lamps
< 2 W
2 – 8 W
> 8 W
60 W
180 W
200 W
Guidance value max. inrush current level 800 A /200 µs
Maximum number EBs T5/T8 16 x 54/58 W, 24 x 35/36 W
8 x 2 x 54/58 W
12 x 2 x 35/36 W
Connection type Screw terminals
Max. cable cross-section max. 2 x 2.5 mm²
Size of ush-mounted box Size 1, Ø 55 mm (NIS, PMI)
Protection rating IP 20 (IP 40 installed)
Ambient temperature 0 °C – 50 °C
CE Declaration of Conformity This device conforms to the
safety regulations of the EMC
directive 2014/30/EU and of
NSR 2014/35/EU.
Product overview
Type of
installation
Channel Operating
voltage
Colour Type Item
number
Ceiling
installation
Light 230 V AC White thePrema
S360 -100 E
2070600
Ceiling
installation
Light 230 V AC Grey thePrema
S360 -100 E
2070601
Ceiling
installation
Light 230 V AC Special colour
in accordance
with customer
information
thePrema
S360 -100 E
2070603

10
Troubleshooting
Fault Cause
Light does not switch
on and/or off if pre-
sence is detected and
in darkness
Lux value is set too low; detector set on semi-au-
tomatic; light was switched off manually via push
button or theSenda S; person not within detection
area; obstruction(s) interrupting detection; time
delay set too short
Light stays on with
detection of presence
despite sufcient
brightness
Lux value is set too high; light was briey switched
on manually via push button or with theSenda S
(wait 30 min.); detector is in test mode
Light does not switch
off and/or light swit-
ches on spontaneously
when no one is present
Wait for time delay (self-learning);
thermal sources of interference in the detection
area: fan heaters, incandescent lamps/halogen
spotlights, moving objects (e.g. curtains hanging in
an open windows);
Load (EBs, relays) not cleared
Push button does not
function
Device still in the start-up phase; illuminated push
button was used without neutral conductor;
Push button not led to the master
Light cannot be swit-
ched off with the push
button
DIP switch to "corridor" position; push button
not fed to the detector. Check wiring to the push
button
Device does not
respond
Short circuit or several phases in parallel switching!
Disconnect detector from the power supply for 5
mins. (thermal fuse)
Error ashing
(4 x per second)
Error in self-test;
Device not properly functional!
Guarantee
ThebenHTS presence detectors are manufactured with the
utmost care and using state-of-the-art technology and are
quality-tested. ThebenHTS AG therefore guarantees perfect
operation when used correctly. Should a fault occur, however,
ThebenHTS AG will full the guarantee within the scope of the
general terms and conditions.
Please note in particular:
•that the guarantee period lasts 24 months from the date
of manufacture.
•that the guarantee is invalidated if you, or a third party,
make changes or undertake repairs to the devices.
•that, insofar as the presence detectors are connected
to a software-controlled system, the guarantee for this
connection is only valid when the indicated interface
specication is complied with.
We undertake to repair or replace as quickly as possible
all components of the delivered device that have become
defective or unusable through demonstrably poor material,
faulty construction or incomplete delivery up to the end of the
guarantee period.
Returns
In the event of a guarantee claim, please return the device to
the relevant dealer together with the delivery note and a brief
description of the fault.
Industrial property rights
The design as well as hardware and software of these devices
are protected by copyright.
Dimensions diagrams
Flush-mounting
Surface-mounted
Ceiling installation

11
Back box (surface mounting) 110A
Item No.: 9070912
Details > www.theben.de
Ceiling installation box 73A
Item No.: 9070917
Details > www.theben.de
SendoPro 868-A
Item No.: 9070675
Details > www.theben.de
theSenda S
Item No.: 9070911
Details > www.theben.de
theSenda P
Item No.: 9070910
Details > www.theben.de
ThebenHTS AG
Im Langhag 7b
8307 Effretikon
SWITZERLAND
Phone [phone]
Fax [phone]
Hotline
Phone [phone]
[email protected]
Addresses, telephone numbers, etc.
www.theben-hts.ch