Thermo Scientific Solaris Series User manual

Thermo Scientific
Solaris Shaker Series
Instruction Manual
70900190-e • 2023-03

Contents
Preface � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
About This Manual � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
Intended Use� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
Open Air Shaker � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
Incubated and Refrigerated Shaker � � � � � � � � � � � � 5
Required Skills � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5
Signal Words and Symbols � � � � � � � � � � � � � � � � � � � � � � 6
Symbols used on Shaker and Accessories � � � � � � 6
Symbols used in the Instruction Manual � � � � � � � � 7
Safety Instructions � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7
1� Technical Specifications� � � � � � � � � � � � � � � � � � � 12
1� 1� Technical Data � � � � � � � � � � � � � � � � � � � � � � � � � � 12
Thermo Scientific Solaris 2000 Shaker � � � � � � � � 12
Thermo Scientific Solaris 4000 Shaker � � � � � � � � 13
Thermo Scientific Solaris 2000 I Shaker � � � � � � � 14
Thermo Scientific Solaris 4000 I Shaker � � � � � � � 15
Thermo Scientific Solaris 2000 R Shaker � � � � � � 16
Thermo Scientific Solaris 4000 R Shaker � � � � � � 17
1� 2� Accessories� � � � � � � � � � � � � � � � � � � � � � � � � � � � � 18
1� 2� 1� Platforms� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 19
1� 2� 2� Flask Clamps � � � � � � � � � � � � � � � � � � � � � � � � � � � � 20
1� 2� 3� Microplate / DeepWell Plate Clamps � � � � � � � � � � 24
1� 2� 4� Test Tube Racks � � � � � � � � � � � � � � � � � � � � � � � � � � 25
1� 2� 5� Adjustable Angle Test Tube Rack Holders � � � � � � 29
1� 2� 6� Adjustable Vessel Clamps � � � � � � � � � � � � � � � � � � 30
1� 2� 7� Square Media Clamps � � � � � � � � � � � � � � � � � � � � � 32
1� 2� 8� Nalgene Beaker Racks � � � � � � � � � � � � � � � � � � � � � 33
1� 2� 9� Separatory Funnel Clamp � � � � � � � � � � � � � � � � � � � 38
1� 2� 10� Utility Tray � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 39
1� 2� 11� Adhesive Mats � � � � � � � � � � � � � � � � � � � � � � � � � � 40
1� 2� 12� General Accessories� � � � � � � � � � � � � � � � � � � � � � 42
1� 3� Directives and Standards � � � � � � � � � � � � � � � � � 43

1� 4� Product Overview� � � � � � � � � � � � � � � � � � � � � � � � 44
1� 4� 1� Solaris 2000 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 44
1� 4� 2� Solaris 4000 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 44
1� 4� 3� Solaris 2000 I / 2000 R� � � � � � � � � � � � � � � � � � � � � 45
1� 4� 4� Solaris 4000 I / 4000 R� � � � � � � � � � � � � � � � � � � � � 45
1� 4� 5� Connections � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 46
2� Transport and Set Up � � � � � � � � � � � � � � � � � � � � � 49
2� 1� Unpacking � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 49
Items Supplied � � � � � � � � � � � � � � � � � � � � � � � � � � � 49
2� 2� Location� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 50
2� 3� Transporting � � � � � � � � � � � � � � � � � � � � � � � � � � � � 52
Handling the Shaker� � � � � � � � � � � � � � � � � � � � � � � 52
2� 4� Leveling � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 53
2� 5� Mains Connection � � � � � � � � � � � � � � � � � � � � � � � 53
2� 6� Initial Startup� � � � � � � � � � � � � � � � � � � � � � � � � � � � 55
2� 7� Storage � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 60
2� 8� Shipping� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 60
3� Operation � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 61
3� 1� Power on / off � � � � � � � � � � � � � � � � � � � � � � � � � � � 61
3� 2� Graphical User Interface � � � � � � � � � � � � � � � � � � 61
3� 2� 1� Set Basic Shaker Operating Parameters � � � � � � � 62
3� 2� 2� Status � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 67
3� 2� 3� Settings� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 70
3� 2� 4� Programs� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 80
3� 3� Accessories� � � � � � � � � � � � � � � � � � � � � � � � � � � � � 90
3� 3� 1� Platform Installation � � � � � � � � � � � � � � � � � � � � � � � 91
3� 3� 2� Flask Clamp and Vessel Installation� � � � � � � � � � � 94
3� 3� 3� Square Clamp Installation � � � � � � � � � � � � � � � � � � 96
3� 3� 4� Test Tube Rack Installation� � � � � � � � � � � � � � � � � � 98
3� 3� 5� Adjustable Angle Test Tube Rack Holder Installation
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 99
3� 3� 6� Microplate / DeepWell-Plate Clamp Installation� 100
3� 3� 7� Adjustable Vessel Clamp Installation � � � � � � � � � 101

3� 3� 8� Beaker Rack Installation� � � � � � � � � � � � � � � � � � � 103
3� 3� 9� Separatory Funnel Clamp Installation� � � � � � � � � 104
3� 3� 10� Utility Tray Installation� � � � � � � � � � � � � � � � � � � � 107
3� 3� 11� Adhesive Mat Installation and Use� � � � � � � � � � 108
3� 3� 12� Gassing Manifold Installation � � � � � � � � � � � � � � 115
3� 4� Loading and Normal Use� � � � � � � � � � � � � � � � � 117
Loading� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 118
Normal Use� � � � � � � � � � � � � � � � � � � � � � � � � � � � � 119
4� Maintenance and Care � � � � � � � � � � � � � � � � � � � 123
4� 1� Basics � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 124
Inspection of Accessories � � � � � � � � � � � � � � � � � 125
4� 2� Cleaning � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 125
Touchscreen � � � � � � � � � � � � � � � � � � � � � � � � � � � � 125
4� 3� Disinfection � � � � � � � � � � � � � � � � � � � � � � � � � � � � 126
4� 4� Decontamination � � � � � � � � � � � � � � � � � � � � � � � 126
4� 5� Autoclaving � � � � � � � � � � � � � � � � � � � � � � � � � � � � 127
4� 6� Temperature Calibration � � � � � � � � � � � � � � � � � 128
4� 6� 1� Temperature Calibration Best Practices � � � � � � 128
4� 6� 2� Temperature Calibration Procedure � � � � � � � � � � 128
4� 6� 3� Temperature Calibration Lookup � � � � � � � � � � � � 132
4� 7� Firmware Installation � � � � � � � � � � � � � � � � � � � � 132
4� 8� Platform Replacement � � � � � � � � � � � � � � � � � � � 136
4� 9� Service� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 136
4� 10� Shipping and Disposal � � � � � � � � � � � � � � � � � � 136
5� Troubleshooting� � � � � � � � � � � � � � � � � � � � � � � � � 137
GPL (General Public License) � � � � � � � � � � � � � � � 140
Index � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 141

5 / 143
Preface
About This Manual
This user manual describes the following shakers and the compatible
accessories ("1. 2. Accessories" on page 18):
Shaker Art. No.
Thermo Scientific Solaris 2000 Shaker, 100–240 V ±10 %, 50 / 60 Hz SK2000
Thermo Scientific Solaris 4000 Shaker, 100–240 V ±10 %, 50 / 60 Hz SK4000
Thermo Scientific Solaris 2000 I Shaker, 100–120, 200–240 V ±10 %, 50 / 60 Hz SK2001
Thermo Scientific Solaris 4000 I Shaker, 100–120, 200–240 V ±10 %, 50 / 60 Hz SK4001
Thermo Scientific Solaris 2000 R Shaker, 100–240 V ±10 %, 50 / 60 Hz SK2002
Thermo Scientific Solaris 4000 R Shaker, 100–240 V ±10 %, 50 / 60 Hz SK4002
Rather than by their full product name, the descriptions and instructions
given in this manual simply refer to each shaker by class:
Open Air Shaker
Incubated Shaker
Refrigerated Shaker
Intended Use
Open Air Shaker
A device used in research and manufacturing to shake solutions in a 2D orbit
while controlling speed and time in applications.
Incubated and Refrigerated Shaker
A device used in research and manufacturing to shake solutions in a 2D orbit
while controlling speed, time and temperature in applications.
Required Skills
This shaker must be operated by trained personnel only.

6 / 143
Signal Words and Symbols
Signal Word Degree of Hazard
WARNING Indicates a hazardous situation that, if not avoided, could result
in death or serious injury.
CAUTION Indicates a hazardous situation that, if not avoided, could result
in minor or moderate injury.
NOTICE Indicates information considered important, but not hazard-
related.
Symbols used on Shaker and Accessories
Observe the information contained in this instruction manual to keep yourself and
your environment safe.
Refer to instruction manual
Disconnect mains plug
General hazard
Hazard caused by hot surface
Risk of finger or hand injuries
caused by mechanical parts
shutting inadvertently

7 / 143
Symbols used in the Instruction Manual
Observe the information contained in the instruction manual to keep yourself and your
environment safe.
General hazard Electrical hazard
Biological hazard Danger of cuts
Hazard caused by
flammable materials
Indicates information
considered important,
but not hazard-related.
Risk of finger or hand
injuries caused by
mechanical parts
shutting inadvertently
Safety Instructions
WARNING
Not following these safety instructions can lead to
hazardous situations that, if not avoided, could result in
death or serious injury.
Observe the safety instructions.
The shaker is to be used for its intended use only.
Improper use can cause damage, contamination,
and injuries with fatal consequences.
The shaker must be operated by trained personnel
only.
It is the obligation of the operator to make sure, that
the proper personal protective equipment is used.
Mind the “Laboratory Biosafety Manual” of the World
Health Organization (WHO) and the regulations in
your country.
WARNING
Damage from inappropriate power supply.
Make sure that the shaker is plugged only into sockets
which have been properly grounded.

8 / 143
WARNING
Risk from handling hazardous substances.
When working with corrosive samples (salt solutions,
acids, bases), the accessories and the shaker have to
be cleaned thoroughly.
The shaker is neither inert nor protected against
explosion. Never use the shaker in an explosion-
prone environment.
Do not shake toxic or radioactive materials or
any pathogenic micro-organisms without suitable
safety precautions.
If shaking any hazardous materials mind the
“Laboratory Biosafety Manual” of the World
Health Organization (WHO) and any local
regulations. When shaking microbiological
samples from the Risk Group II (according
to the “Laboratory Biosafety Manual” of the
World Health Organization (WHO)), aerosol-tight
biological seals have to be used. Look on the
Internet page of the World Health Organization
(www.who.int) for the “Laboratory Biosafety
Manual”. For materials in a higher risk group, extra
safety measures must be taken.
If toxins or pathogenic substances have
contaminated the shaker or its parts, appropriate
disinfection and decontamination measures have
to be taken ("Decontamination" on page 126;
„Disinfection“ on page 126).
If a hazardous situation occurs, turn off the
power supply to the shaker and leave the area
immediately.
WARNING
Damage to health from infectious substances.
If an accidental spill places liquids or other materials
under the platform, immediately power off the shaker,
unplug it, and remove the platform ("Platforms" on
page 19).
Clean up the spill following your regular laboratory
procedures. Use proper personal protective
equipment.

9 / 143
WARNING
Damage to health from shaking explosive or
flammable materials or substances.
Do not shake explosive or flammable materials or
substances.
CAUTION
Burnings from hot surfaces.
In a temperature controlled shaker the surfaces like
platform and accessories can get hot under the hood.
Do not touch hot surfaces. Wait until the hot surfaces
have cooled down.
CAUTION
Cutting injuries from glass shards.
A disengaged platform and accessories, like clamps,
can lead to broken glass if vessels fall off the shaker.
Make sure that the platform and accessories are
installed properly by using the correct tools and
screws. Make sure that the clamps are capable to hold
the load of the vessel and sample at chosen speed.
Clamps with your individually configured load may
have lower speed capability than the stability limitation
of the shaker. Refer to "3. 4. Loading and Normal Use"
on page 117.
Pay attention to any unusual sound. This can indicate a
disengaged platform or accessories.
CAUTION
Damage to shaker or malfunction due to a
damaged touchscreen.
Do not operate the shaker if the touchscreen is
damaged.
Power off the shaker. Disconnect the mains plug.
Have the touchscreen replaced by an authorized
service technician.

10 / 143
CAUTION
Biological harm due to broken or leaking vessels.
Improperly installed accessories can lead to spilled
samples.
Make sure that accessories are installed properly
by using the correct tools and screws.
Make sure that accessories fit reasonably on the
platform.
Always use a vessel with an accessory of the
proper size.
Vessels must be intact and installed properly.
CAUTION
Safety can be impaired by improper loading and
damaged accessories.
Always make sure that the load (accessories and
samples) is distributed as equally as possible,
especially when operating a dual stack platform.
Do not use accessories which show signs of
corrosion or cracks. Contact customer service for
further information.
Use only shakers which have been loaded properly.
Never overload the shaker.
Make sure the accessories are installed properly
before operating the shaker. Follow the instructions
in section „Accessories“ on page 90.

11 / 143
CAUTION
Physical harm caused by ignoring operative basics.
Never operate the shaker without a properly
installed platform.
Never use the shaker if parts of its exterior are
damaged or missing.
Never use a shaker with a defective hood spring. A
defective hood spring is unable to safely hold the
hood in the fully open position.
Do not move the shaker while it is running.
Do not lean on the shaker.
Never load or unload the shaker until it has come to
a complete stop and this has been confirmed on the
touchscreen.
Do not put anything on the shaker while it is
running.
Do not touch the platform or any accessories on the
shaker while it is running.
The shaker housing is not to be opened by the
operator.
NOTICE
Protection may be impaired by incompatible
accessories.
Use only accessories for this shaker which have been
approved by Thermo Fisher Scientific. For updated lists
check www.thermofisher.com.
NOTICE
To shut down the shaker:
Press the STOP key. Turn off the shaker at the
main switch. Pull out the power supply plug. In an
emergency disconnect the power supply.

12 / 143
Technical Data
1. Technical Specifications
1. 1. Technical Data
Thermo Scientific Solaris 2000 Shaker
Speed Range 15–525 rpm
Running Time 99 h 59 min (1 min increments) or continuous mode
Noise Level at max. Speed 50 dB (A) (1 m in front of the unit at 1.6 m height)
Maximum Load (incl. Platform,
Accessories and Samples) 25 kg (55 lbs)
Electrical Connection 100–240 V ±10 %, 50 / 60 Hz
Power Consumption 60 W
Environmental Conditions
For Storage and Shipping Temperature: -10 °C to 55 °C
Humidity: 15% to 85%
For Operation Use in interior spaces
Altitudes of up to 3000 m above sea level
Temperature: 5 °C to 40 °C
Max. relative humidity 80% up to 31 °C; decreasing linearly to
50% relative humidity at 40 °C
Pollution Degree 2
Overvoltage Category II
IP 20
Interfaces USB Ethernet
2x USB-A 2.0 RJ45
Dimensions Length Width Height
47 cm
(18.5 in)
37 cm
(14.5 in)
15 cm
(5.5 in)
Weight 20.9 kg (46,0 lbs)
Table 1: Technical Data Solaris 2000

13 / 143
Technical Data
Thermo Scientific Solaris 4000 Shaker
Speed Range 15–525 rpm
Running Time 99 h 59 min (1 min increments) or continuous mode
Noise Level at max. Speed 54 dB (A) (1 m in front of the unit at 1.6 m height)
Maximum Load (incl. Platform,
Accessories and Samples) 43 kg (95 lbs)
Electrical Connection 100–240 V ±10 %, 50 / 60 Hz
Power Consumption 80 W
Environmental Conditions
For Storage and Shipping Temperature: -10 °C to 55 °C
Humidity: 15% to 85%
For Operation Use in interior spaces
Altitudes of up to 3000 m above sea level
Temperature: 5 °C to 40 °C
Max. relative humidity 80% up to 31 °C; decreasing linearly to
50% relative humidity at 40 °C
Pollution Degree 2
Overvoltage Category II
IP 20
Interfaces USB Ethernet
2x USB-A 2.0 RJ45
Dimensions Length Width Height
65 cm
(25.6 in)
58 cm
(22.8 in)
18 cm
(7 in)
Weight 75.1 kg (165.5 lbs)
Table 2: Technical Data Solaris 4000

14 / 143
Technical Data
Thermo Scientific Solaris 2000 I Shaker
Speed Range 15–525 rpm
Temperature Setting Range 30–60 °C
Temperature Stability in Flask
at 37 °C
Ambient temperature 23 °C; for 1 h with stable chamber
temperature
± 0.1 °C
Temperature Uniformity in Flask
at 37 °C
Ambient temperature 23 °C; for 1 h with stable chamber
temperature
± 0.5 °C
Running Time 99 h 59 min (1 min increments) or continuous mode
Noise Level at max. Speed 52 dB (A) (1 m in front of the unit at 1.6 m height)
Maximum Load (incl. Platform,
Accessories and Samples)
16 kg (35 lbs),
including 11x14 platform at 2.3 kg (5.1 lbs)
Electrical Connection 100–120, 200–240 V ±10 %, 50 / 60 Hz
Power Consumption 900 W
Environmental Conditions
For Storage and Shipping Temperature: -10 °C to 55 °C
Humidity: 15% to 85%
For Operation Use in interior spaces
Altitudes of up to 3000 m above sea level
Temperature: 5 °C to 40 °C
Max. relative humidity 80% up to 31 °C; decreasing linearly to
50% relative humidity at 40 °C
Pollution Degree 2
Overvoltage Category II
IP 20
Interfaces USB Ethernet
2x USB-A 2.0 RJ45
Dimensions Length Width Height
70 cm
(27.6 in)
36 cm
(14.2 in)
46 cm
(18.1 in)
With open Hood 79 cm
(30.8 in)
Weight 44.9 kg (99 lbs)
Table 3: Technical Data Solaris 2000 I

15 / 143
Technical Data
Thermo Scientific Solaris 4000 I Shaker
Speed Range 15–525 rpm
Temperature Setting Range 30–60 °C
Temperature Stability in Flask
at 37 °C
Ambient temperature 23 °C; for 1 h with stable chamber
temperature
± 0.1 °C
Temperature Uniformity in Flask
at 37 °C
Ambient temperature 23 °C; for 1 h with stable chamber
temperature
± 0.5 °C
Running Time 99 h 59 min (1 min increments) or continuous mode
Noise Level at max. Speed 52 dB (A) (1 m in front of the unit at 1.6 m height)
Maximum Load (incl. Platform,
Accessories and Samples)
32 kg (70.5 lbs),
including 18x18 platform at 4.3 kg (9.5 lbs)
Electrical Connection 100–120, 200–240 V ±10 %, 50 / 60 Hz
Power Consumption 900 W
Environmental Conditions
For Storage and Shipping Temperature: -10 °C to 55 °C
Humidity: 15% to 85%
For Operation Use in interior spaces
Altitudes of up to 3000 m above sea level
Temperature: 5 °C to 40 °C
Max. relative humidity 80% up to 31 °C; decreasing linearly to
50% relative humidity at 40 °C
Pollution Degree 2
Overvoltage Category II
IP 20
Interfaces USB Ethernet
2x USB-A 2.0 RJ45
Dimensions Length Width Height
77 cm
(30.3 in)
57 cm
(22.4 in)
55 cm
(21.7 in)
With open Hood 94 cm
(36.7 in)
Weight 68.1 kg (150.1 lbs)
Table 4: Technical Data Solaris 4000 I

16 / 143
Technical Data
Thermo Scientific Solaris 2000 R Shaker
Speed Range 15–525 rpm
Temperature Setting Range 5–60 °C
Temperature Stability in Flask
at 37 °C
Ambient temperature 23 °C; for 1 h with stable chamber
temperature
± 0.1 °C
Temperature Uniformity in Flask
at 37 °C
Ambient temperature 23 °C; for 1 h with stable chamber
temperature
± 0.5 °C
Running Time 99 h 59 min (1 min increments) or continuous mode
Noise Level at max. Speed 56 dB (A) (1 m in front of the unit at 1.6 m height)
Maximum Load (incl. Platform,
Accessories and Samples)
16 kg (35 lbs),
including 11x14 platform at 2.3 kg (5.1 lbs)
Electrical Connection 100–240 V ±10 %, 50 / 60 Hz
Power Consumption 350 W
Environmental Conditions
For Storage and Shipping Temperature: -10 °C to 55 °C
Humidity: 15% to 85%
For Operation Use in interior spaces
Altitudes of up to 3000 m above sea level
Temperature: 5 °C to 40 °C
Max. relative humidity 80% up to 31 °C; decreasing linearly to
50% relative humidity at 40 °C
Pollution Degree 2
Overvoltage Category II
IP 20
Interfaces USB Ethernet
2x USB-A 2.0 RJ45
Dimensions Length Width Height
70 cm
(27.6 in)
36 cm
(14.2 in)
46 cm
(18.1 in)
With open Hood 79 cm
(30.8 in)
Weight 47.2 kg (104.1 lbs)
Table 5: Technical Data Solaris 2000 R

17 / 143
Technical Data
Thermo Scientific Solaris 4000 R Shaker
Speed Range 15–525 rpm
Temperature Setting Range 4–60 °C
Temperature Stability in Flask
at 37 °C
Ambient temperature 23 °C; for 1 h with stable chamber
temperature
± 0.1 °C
Temperature Uniformity in Flask
at 37 °C
Ambient temperature 23 °C; for 1 h with stable chamber
temperature
± 0.5 °C
Running Time 99 h 59 min (1 min increments) or continuous mode
Noise Level at max. Speed 56 dB (A) (1 m in front of the unit at 1.6 m height)
Maximum Load (incl. Platform,
Accessories and Samples)
32 kg (70.5 lbs),
including 18x18 platform at 4.3 kg (9.5 lbs)
Electrical Connection 100–240 V ±10 %, 50 / 60 Hz
Power Consumption 750 W
Environmental Conditions
For Storage and Shipping Temperature: -10 °C to 55 °C
Humidity: 15% to 85%
For Operation Use in interior spaces
Altitudes of up to 3000 m above sea level
Temperature: 5 °C to 40 °C
Max. relative humidity 80% up to 31 °C; decreasing linearly to 50%
relative humidity at 40 °C
Pollution Degree 2
Overvoltage Category II
IP 20
Interfaces USB Ethernet
2x USB-A 2.0 RJ45
Dimensions Length Width Height
77 cm
(30.3 in)
57 cm
(22.4 in)
55 cm
(21.7 in)
With open Hood 94 cm
(36.7 in)
Weight 74.9 kg (165.1 lbs)
Table 6: Technical Data Solaris 4000 R

18 / 143
Accessories
1. 2. Accessories
CAUTION
Protection may be impaired by incompatible
accessories.
Use only accessories for this shaker which have been
approved by Thermo Fisher Scientific.
For updated lists check www.thermofisher.com.

19 / 143
Accessories
1. 2. 1. Platforms
Platform Art. No.
Solaris 2000 Weight
Thermo Scientific Solaris 12x14 Universal Platform 2.7 kg (5.9 lbs) SK1214
Thermo Scientific Solaris 12x14 Dual Stack Universal Platform 6.4 kg (14.1 lbs) SK1214D
Thermo Scientific Solaris 12x14 Dual Stack Universal Platform
Upgrade Kit
SK1214DK
Thermo Scientific Solaris 18x18 Universal Platform 4.3 kg (9.4 lbs) SK1818
Thermo Scientific Solaris 18x18 Dual Stack Universal Platform 9.7 kg (21.3 lbs) SK1818D
Thermo Scientific Solaris 18x18 Dual Stack Universal Platform
Upgrade Kit
SK1818DK
Thermo Scientific Solaris 18x24 Universal Platform 6.0 kg (13.2 lbs) SK1824
Solaris 4000
Thermo Scientific Solaris 18x30 Universal Platform 7.5 kg (16.5 lbs) SK1830
Thermo Scientific Solaris 18x30 Dual Stack Universal Platform 16.3 kg (35.9 lbs) SK1830D
Thermo Scientific Solaris 18x30 Dual Stack Universal Platform
Upgrade Kit
SK1830DK
Thermo Scientific Solaris 36x24 Universal Platform 12.0 kg (26.4 lbs) SK3624
Solaris 2000 I / 2000 R
Thermo Scientific Solaris 11x14 Universal Platform 2 .3 kg (5.1 lbs) SK1114
Solaris 4000 I / 4000 R
Thermo Scientific Solaris 18x18 Universal Platform 4.3 kg (9.5 lbs) SK1818
Spare Kits and Accessories
Clamp Spare Kit (Screws) SK1001
Platform Spare Kit Small (Platform Screws, Tool) SK0100
Platform Spare Kit Large (Platform Screws, Tool) SK0101
Screwdriver for Accessories 75004131
Table 7: Available Platforms