Toro 104-8950 User manual

2003 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
Contact us at www.Toro.com
All Rights Reserved
Printed in the USA
Original Instructions (EN)
CE Kit
for Multi-Pro1200 and 1250 Sprayers
Model No. 104–8950
Form No. 3329-906
Installation Instructions
Safety and Instruction Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or lost.
104-8939
1. Engine oil level (dipstick)
2. Engine oil filter
3. Transaxle/hydraulic fluid
level (dipstick)
4. Transaxle hydraulic filter
5. Hydraulic strainer
6. Gear box fluid level
7. Brake fluid
8. Belts, steering and drive
9. Fuel, unleaded only
10. Fuel filter
11. Battery
12. Air cleaner
13. Grease
14. Tire pressure
15. Read the instructions before
servicing or performing
maintenance.
16. Pump

2
Loose Parts
Note: Use the chart below to verify that all parts have been shipped.
Description Qty. Use
Flange bolt (5/16 x 3/4 inch)
Flange nut (5/16 inch) 2 2Installing the battery cover fasteners
Shroud bracket
Shroud-pump drive
Flange bolt (1/4 x 1/2 inch)
Flange nut (1/4 inch)
1
2
4
4
Installing the pump shroud
Pressure gauge 1Installing the pressure gauge
Horn
Bolt (5/16 x 3/4 inch)
Flange nut (5/16 inch)
Horn button
Lock ring
Screw
Horn wire harness
1
1
1
1
1
2
1
Installing the horn
Cover
Wire ties 1 6Installing the hose cover
Decal 1Applying the decal
Installation Instructions 1Read before installing the kit
CE Certificate 1 Verification
Parts Catalog 1Use for ordering replacement parts

3
Installing the Battery Cover
Fasteners
Replace the existing hand knobs with the provided
fasteners.
1. Loosen and remove the two hand knobs securing
battery cover to battery base (Fig. 1).
1
1
2
3
Figure 1
1. Hand knobs
2. Battery 3. Battery cover
2. Install the two flange bolts (5/16 x 3/4 inch) and two
flange nuts (5/16 inch) in place of the removed hand
knob to secure the battery cover.
Installing the Pump Shroud
Install the pump shroud to cover the pump drive.
1. Loosen the two pump bolts in the pump face and install
the shroud support as shown in figure 2.
1
2
3
4
5
6
m–6949
Figure 2
1. Shroud support
2. Pump bolt (9 x 10 mm)
3. Spring lock washer
4. Flange bolt
(1/4 x 1/2 inch)
5. Flange nut (1/4 inch)
6. Shroud
2. Tighten bolts to secure the shroud support.
3. Assemble the shroud as shown in figure 2 using the four
flange bolts (1/4 x 1/2 inch) and four flange nuts
(1/4 inch).

4
Installing the Pressure Gauge
Replace the existing pressure gauge with the new gauge
capable of displaying pressure in kPa.
1. Using a wrench, hold the reducer at the tee bracket and
loosen the existing pressure gauge. Remove the gauge
(Fig. 3).
m–6956
1
2
3
4
Figure 3
1. Pressure gauge
2. Reducer 3. Tee bracket 4. Reducer nut and coupler
2. Apply sealer tape to threads of the new pressure gauge
and install it into the reducer. Use a wrench to hold
reducer while tightening the new pressure gauge.
3. Position the gauge so it can be viewed by the operator.
Note: The reducer nut may need to be loosened and the
whole assembly turned to allow the gauge to be viewed.
Installing the Horn
1. Drill a hole, 11/32 inch in diameter, in the vehicle frame
under the floorboard. The hole should be 4 cm
(1-1/2 inches) down from the frame top and 5 cm
(2 inches) from the front of the frame (Fig. 4).
2. Secure the horn to the frame using a bolt
(5/16 x 3/4 inch) and a flange nut (5/16 inch) as shown
in figure 4.
m–695
7
3
2
1
45
3
4 cm
5 cm
Figure 4
1. Vehicle frame
2. Bolt (5/16 x 3/4 inch)
3. Tire, left front
4. Horn
5. Flange nut (5/16 inch)
3. Drill a hole, 5/8 inch in diameter, in the dash panel. The
hole should be 23 cm (9 inches) to the left of the
steering column base and 5 cm (2 inches) from the top
of the dash (Fig. 5).
m–6958
1
23
23 cm
5 cm
Figure 5
1. Horn button
2. Dash 3. Steering column

5
4. Open the horn button packing that includes the horn
switch and button cap, 2 screws, and a retaining ring.
5. Remove the horn button cap and thread the retaining
ring onto the exposed threads of the switch.
6. Connect the two red wires at the end of the wiring
harness to the back of the horn switch using the two
screws included.
7. Move the switch assembly under the dash and push it
through the hole drilled in step 3.
8. Screw the horn button cap onto the switch threads to
secure the assembly to the dash.
Note: Adjust the retaining ring and horn button cap as
necessary.
9. Run the horn wire harness from the horn button, under
the dash panel, through the wire access hole in the
floorboard, and through the frame hooks along side of
the headlight wire harness to the electrical panel located
under the operator’s seat.
10.Connect the single black wire (ground) in the middle of
the wire harness to the bolt located to the right of the of
the wire access hole on the floorboard near the foot
switch.
11. Connect the two quick connect terminals to the horn.
12.Connect the red power wire to the right side of the
solenoid (Fig. 6), located under the seat.
m–6553
1
2
Figure 6
1. Red power wire from the electrical box on the hose reel.
2. Solenoid
Note: Connecting the wire harness to the right solenoid
post will allow the horn to be active when the ignition key
is in the Off position.
Installing the Hose Cover
1. Locate the hydraulic hoses under the dash panel
(Fig. 7).
2. Remove all existing wire ties securing hydraulic hoses
and separate the small wire loom (Fig. 7).
m–6968
1
4
5
6
7
2
3
Figure 7
1. Hydraulic hoses
2. Existing wire ties
3. Small wire loom
4. Steering control unit
5. Wire access hole
6. Hose cover
7. New wire ties
3. Install large hose cover over the hydraulic hoses only.
Note: Make sure the slit in the hose cover is positioned to
the front of the vehicle (away from the operator).
4. Position the cover so that it extends down through the
wire access hole in the floorboard and up to the steering
control unit (Fig. 7).
5. Secure the cover with new wire ties supplied with the
kit (Fig. 7).

6
Applying the Decal
The decal included in the this kit replaces the existing
decal, part number 100–8620 (Fig. 8).
100–8620
Figure 8
1. Clean the existing decal (Fig. 8), located on the left
front of the seat box and surrounding area. Make the it
are is free of dirt, grease, or other foreign material.
2. Remove the backing of the new decal and place directly
over the existing decal. The decal should cover the old
decal completely (Fig. 9).
104–8939
Figure 9

7