Toro 131-3302 User manual

FormNo.3389-137RevA
MultiPro®WMTurfSprayerFinishingKit
ManualWorkman®UtilityVehicle
ModelNo.131-3302
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
UseofthisproductmaycauseexposuretochemicalsknowntotheStateofCalifornia
tocausecancer,birthdefects,orotherreproductiveharm.
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescriptionQty.Use
1Drive-shaft-shieldbracket1Installthedrive-shaftshieldonthe
sprayerpump.
PTOdriveshaft1
Woodruffkey1
Setscrew2
Drive-shaftshield1
Clip2
2
Flange-headbolt(1/4x3/4inch)2
InstallthePTOshaftandthedrive-shaft
shieldtothesprayerpump.
Hydraulichose(5/8x55.6inches)1
Hydraulichose(5/8x85.2inches)1
Malequickcoupler1
Femalequickcoupler1
Tubeclamp2
Clampbolt(5/16x1-1/2inches)1
3
Cabletie3
Installthehydraulichosesfortheboom
liftcylinders.
4Nopartsrequired–CouplethePTOshafttothetransaxle.
Note:Removethecargoboxoratbedfromthevehiclebeforeinstallingthiskit;refertotheOperator’sManualforthevehicle.
Note:ForNon-TCmodels,installtheRearPTOKitbeforeinstallingthiskit;contactyourAuthorizedToroDistributor
aboutpurchasingthiskit.
©2014—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3389-137*A

1
Installingthe
Drive-Shaft-ShieldBracket
ontheSprayerPump
Partsneededforthisprocedure:
1Drive-shaft-shieldbracket
Procedure
1.Removethe2boltsattheleftandrightoftheinput
shaftofthesprayerpump(Figure1).
Figure1
1.Bolts
2.Applymedium-dutythread-lockingcompoundtothe
bolts.
3.Installthedrive-shaft-shieldbracketontothesprayer
pumpwiththe2boltsremovedinstep1asshownin
Figure2.
Figure2
1.Drive-shaft-shieldbracket2.Boltsfromthesprayer
pump
4.Torquetheboltsto23to26N-m(17to21ft-lb).
2
InstallthePTOShaftand
theDrive-ShaftShieldtothe
SprayerPump
Partsneededforthisprocedure:
1PTOdriveshaft
1Woodruffkey
2Setscrew
1Drive-shaftshield
2Clip
2Flange-headbolt(1/4x3/4inch)
Procedure
1.InserttheWoodruffkeyintothekeyslotintheshaft
ofthesprayerpump.
2

Figure3
1.Woodruffkey2.Slot
2.Applyanti-seizingcompoundtothepumpshaftand
theWoodruffkey.
3.Removethe2setscrewsonthePTOshaftend(Figure
4).
Figure4
1.PTOshaftend3.Shaftofthesprayerpump
2.Setscrew(2)
4.Applymedium-duty,thread-lockingcompoundtothe
2setscrewsonthePTOshaftend.
5.AligntheslotinthecouplerofthePTOshaftwiththe
Woodruffkey,andsliptheendofthePTOshaftonto
theshaftofthesprayerpump(Figure4).
6.InstallthesetscrewsinthePTOshaftcoupleruntil
theyaretight.
7.Installthedrive-shaftshieldontotheshield-support
bracketwith2ange-headbolts(1/4x3/4inch)and2
clips(Figure5).
Figure5
1.Flange-headbolt(2)3.Drive-shaftshield
2.Clip(2)
3
InstallingtheHydraulicHoses
fortheBoomLiftCylinders
Partsneededforthisprocedure:
1Hydraulichose(5/8x55.6inches)
1Hydraulichose(5/8x85.2inches)
1Malequickcoupler
1Femalequickcoupler
2Tubeclamp
1Clampbolt(5/16x1-1/2inches)
3Cabletie
Procedure
Note:Ensurethatthetankskidisraisedandthatthe
cylinderlockisinplace.
Note:Ensurethatthecenterboomsectionisinstalled;refer
totheInstallationInstructionsforthesprayer.
1.Assemblethemalequick-connectcouplerontothe
hose(3/8x79-1/2inches)asshowninFigure6and
torquethecouplerto37to45N-m(27to33ft-lb).
3

Figure6
1.Femaleendofhose3.Maleendofhose
2.Malequick-connect
coupler
4.Femalequick-connect
coupler
2.Assemblethefemalequick-connectcouplerontothe
hose(3/8x56-1/2inches)asshowninFigure6and
torquethecouplerto37to45N-m(27to33ft-lb).
3.Routethehosesandsecurethemwithcableties,atube
clamp,andaclampboltasshowninFigure7.
1
2
1
g028547
Figure7
1.Cabletie2.Tubeclampandclamp
bolt
4.RemovethecapfromtheT-ttinginthehydraulictube
nexttothetransmission-oillter(Figure8).
Figure8
1.T-tting2.Transmission-oillter
5.Connectthefreeendofthehose(3/8x55.6inches)to
theT-tting(Figure8)andtorquetheswivelnutofthe
hoseto37to45N-m(27to33ft-lb).
6.RemovethecapfromtheT-ttinginthehydraulictube
nexttothehydraulicuidtank(Figure9).
Figure9
Thecrosstubeisremovedforthepurposeofclarity.
1.Hoseend(connectedto
T-tting)
2.Hydraulicuidtank
7.Connectthefreeendofthehose(3/8x85.2inches)to
theT-tting(Figure8)andtorquetheswivelnutofthe
hoseto37to45N-m(27to33ft-lb).
4

4
CouplingthePTOShafttothe
Transaxle
NoPartsRequired
Procedure
1.AtthefrontyolkofthePTOdriveshaft,alignthe
socketofthefrontyolkwiththesplinesofthePTO
outputshaftonthetransaxle(Figure10).
Figure10
1.Springlock3.PTOoutputshaft
2.PTOdriveshaft
2.Pullthespringlock(rubbercowling)atthefrontyolk
ofPTOdriveshaftrearward(Figure10).
3.Slidethesocketofthefrontyolkovertheoutputshaft
splines(Figure10).
4.PushthespringlockofthefrontyolkofPTOdrive
shaftforward(Figure10).
5.Pullbackthefronthalfofthedriveshafttoensurethat
thelockingballsofthespringlockareseatedinthe
grooveofthePTOoutputshaft(Figure10).
Important:EnsurethatthePTOdriveshaftis
securedtothePTOoutputshaft.
5

Notes:
6

Notes:
7