Toro 07356 User manual

FormNo.3385-461RevA
DoorKitwithSlidingWindow
Workman®MDXorHDXUtilityVehicle
ModelNo.07356
ModelNo.07393
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
Installation
1
PreparingtoInstalltheDoor
Kit
NoPartsRequired
Procedure
1.Movethemachinetoalevelsurfaceandsettheparking
brake.
2.Shutofftheengine,settheparkingbrake,andremove
thekeyfromtheignitionswitch.
2
InstallingtheDoors
Partsneededforthisprocedure:
1Right-handdoor
1Left-handdoor
2Ballstud
2Locknut(5/16inch)
2Doorstrut
4Washer
Procedure
1.Inserttheballstudthroughtherearholeinthebracket
onthecabframe,andinstallthelocknut(5/16inch)
ontotheballstud(Figure1).
Figure1
1.Locknut(5/16inch)3.Frame
2.Bracket4.Ballstud
©2014—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3385-461*A

2.Installthe4washersoverthe4hingepinsatthecab
frameforthemachine(Figure2).
3.Installthedoorontothehingepinsmountedonthe
cabframe(Figure2).
Figure2
1.Door3.Washer
2.Hingepins4.Door-hingemount
4.Installthettingattherodendofthedoorstrutonto
theballstudatthecabframe(Figure3).
Figure3
1.Ballstud(cabframe)3.Fitting(strutcylinder)
2.Fitting(strutrod)4.Ballstud(doorframe)
Note:Thedoor-ttingstruthasaquick-releaseend.
Fliptheleververticallyforinstallation.Onceinstalled,
closethelevertocapturetheballstud(Figure4).
Figure4
1.Lever
5.Installthettingatthecylinderendofthestrutonto
theballstudatthedoorframe(Figure3).
2

3
AssemblingtheLatchPins
Partsneededforthisprocedure:
2Hexnut(7/16inch)
2Latchpin
2Latch-pincam
4Thrustwasher
2Pinguard
Procedure
1.Alignthelatch-pincamwiththeopeningatthestriker
plateinthepositionshowninFigure5.
Figure5
1.Hexnut(7/16inch)4.Thrustwasher
2.Strikerplate5.Latchpin
3.Latch-pincam6.Pinguard
2.Insertthelatchpin(withoutthewashersatrst)into
thelatch-pincam(Figure5).
Note:Ifthelatchpinisnotcenteredinthedoorlatch,
add1or2ofthethrustwashers.
3.Alignthepinguardandthehexnut(7/16inch)onto
thebacksideoftheopeningatthestrikeplate(Figure
5).
4.Tightenthehexnut(7/16inch)ontothelatchpin,so
itisngertight(Figure5).
4
AssemblingtheDoorLanyards
Partsneededforthisprocedure:
2Lanyard
4Shoulderbolt(5/16x1/2inch)
4Locknut(5/16inch)
Procedure
1.Assemblethelanyardtothedoor-framehingewitha
shoulderbolt(5/16x1/2inch)andalocknut(5/16
inch)asshowninFigure6.
Figure6
1.Lanyard3.Locknut(5/16inch)
2.Shoulderbolt(5/16x1/2
inch)
4.Door-framehinge
2.Assembletheotherendofthelanyardtothecabframe
forward-strut-bracketholewithashoulderbolt(5/16
x1/2inch)andalocknut(5/16inch)asshownin
Figure7.
Figure7
1.Locknut(5/16inch)3.Lanyard
2.Bracket4.Shoulderbolt(5/16x1/2
inch)
3

5
AdjustingtheDoor-latchPin
NoPartsRequired
Procedure
1.Centerthelatchpininthelatch-pin-mountbracketon
therail(Figure8).
Figure8
1.Cabframe3.Latchpin
2.Latch-pin-mountbracket4.Hexnut(7/16inch)
2.Closethedoorcompletelyandviewwherethelatch
pincomesintocontactwiththedoorlatch.
Note:Ifthelatchpinisnotcompletelyengagewith
thedoorlatch,add1or2thrustwashersbetweenthe
latch-pincamandthelatchpin.
3.Closethedoorcompletelyandmeasuretheheightof
thebubblesealtothesealingsurfaceofthecabrail,
andensurethatthemeasurementis1.9to2.2cm(3/4
to7/8inch)asshowninFigure9.
Note:Iftheheightmeasuredismorethanthe
zonespecication,rotatethelatch-pincam45°
towardtheinsideofthecabtoachievethespecied
measurement.Iftheheightmeasuredislessthanthe
zonespecication,performtheoppositeoftheabove
procedure.
Note:Thelatchpinwillselfcenter.
Figure9
1.Bubbleseal2.Cabrail
4.Tightenthehexnut(7/16inch)oncethelatchpin
reaches1.9to2.2cm(3/4to7/8inch)asshownin
Figure8.
4

Operation
UsingtheDoor
1.Insertthekeyintotheopeningonthehandleifthe
doorislocked,androtatethekeytotheopenposition
(Figure10).
2.Pushthebuttononthehandleandopenthedoor
(Figure10).
Figure10
1.Key2.Handlebutton
OperatingtheSlidingWindow
Openthelatchtoopenandclosetheslidingwindow(Figure
11).
Figure11
1.Windowlatch
5

Notes:
6

Notes:
7