Toro 140-5036 User manual

FormNo.3439-702RevA
HDVacBaggerBlowerCover
TITAN®Zero-Turn-RadiusRidingMower
ModelNo.140-5036
InstallationInstructions
Safety
SafetyandInstructionalDecals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea
ofpotentialdanger.Replaceanydecalthatisdamagedormissing.
decal136-4164
136-4164
1.Warning—readtheOperator’sManual.4.Cutting/dismembermenthazard,impeller—keepawayfrom
movingparts;keepallguardsandcoversinplace.
2.Warning—hearingprotectionmustbeworn.5.Cutting/dismembermenthazard,impeller—disengagethe
PTO,removethekey,andwaitforallmovingpartstostop.
3.Thrownobjecthazard—donotoperatetheblowerwithoutthe
entiresysteminstalledandlatched.
6.Warning;lossoftraction—donotoperatewithonly
counterbalanceweightsinstalled;donotoperatewithonly
E-ZVacinstalled;operateonlywithbothE-ZVacand
counterbalanceweightsinstalled.
©2020—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3439-702*A

Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescriptionQty.Use
1Nopartsrequired–Preparethemachine.
2Nopartsrequired–Removetheexistingcover.
Cover1
Hex-headbolt(1/4x5/8inch)11
3Locknut(1/4inch)1
Installthenewcover.
1
PreparingtheMachine
NoPartsRequired
Procedure
1.Parkthemachineonalevelsurface.
2.Disengagetheblade-controlswitch.
3.Engagetheparkingbrake.
4.Movethemotion-controlleversoutwardtothe
NEUTRAL-LOCKposition.
5.Shutofftheengineandremovethekey.
2

2
RemovingtheExisting
Cover
NoPartsRequired
Procedure
Removetheexisting5shoulderscrews,5
Phillips-headscrews,blowerguard,andcoverfrom
theblowerassembly(Figure1).
Note:Youcandiscardtheseparts.
g321826
Figure1
1.Shoulderscrew4.Blowerassembly
2.Existingcover5.Blowerguard
3.Phillips-headscrew
3

3
InstallingtheNewCover
Partsneededforthisprocedure:
1Cover
11Hex-headbolt(1/4x5/8inch)
1Locknut(1/4inch)
Procedure
1.Alignthenewcoverwiththeholesontheblower
assembly.
2.Usingthecoverasthetemplate,drill1hole(6.4
mmor1/4inch)intotheblowerchute(Figure2).
g321825
Figure2
1.Drillahole(6.4mmor1/4inch)here.
3.Securethecovertotheblowerassemblyusing
the11hex-headbolts(1/4x5/8inch)and1
locknut(1/4inch)asshowninFigure3.
g322552
Figure3
1.Newcover3.Blowerassembly
2.Hex-headbolt(1/4x5/8
inch)
4.Locknut(1/4inch)
4