Toro 7253 User manual

Operator’s Manual
English (EN)
Form No. 3326-661
Workman2100
Utility Vehicle
Model No. 07253—210001473 and Up
Model No. 07253TC—210001001 and Up

2
All Rights Reserved
Printed in the USA
2001 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
Warning
Important The engine in this product is not equipped
with a spark arrester muffler. It is a violation of California
Public Resource Code Section 4442 to use or operate this
engine on any forest-covered, brush-covered, or
grass-covered land as defined in CPRC 4126. Other states
or federal areas may have similar laws.
This spark ignition system complies with Canadian
ICES-002.
Ce système d’allumage par étincelle de véhicule est
conforme à la norme NMB-002 du Canada.
Contents
Page
Introduction 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safe Operating Practices 3. . . . . . . . . . . . . . . . . . . .
Before Operating 3. . . . . . . . . . . . . . . . . . . . . . . . .
While Operating 4. . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sound Pressure Level 7. . . . . . . . . . . . . . . . . . . . . .
Vibration Level 7. . . . . . . . . . . . . . . . . . . . . . . . . . .
Slope Chart 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety and Instruction Decals 11. . . . . . . . . . . . . . . .
Specifications 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loose Parts 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Rear Wheels 15. . . . . . . . . . . . . . . . . .
Installing the Front Wheels 15. . . . . . . . . . . . . . . . .
Installing the Steering Wheel 15. . . . . . . . . . . . . . . .
Installing the Bumper 16. . . . . . . . . . . . . . . . . . . . . .
Installing the Seats 16. . . . . . . . . . . . . . . . . . . . . . . .
Installing the Hitch 16. . . . . . . . . . . . . . . . . . . . . . . .
Installing the Cargo Box 16. . . . . . . . . . . . . . . . . . . .
Activating the Battery 17. . . . . . . . . . . . . . . . . . . . . .
Checking the Crankcase Oil 18. . . . . . . . . . . . . . . . .
Checking the Tire Pressure 18. . . . . . . . . . . . . . . . . .
Fuel Tank 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Think Safety First 19. . . . . . . . . . . . . . . . . . . . . . . . .
Controls 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pre-Starting Checks 21. . . . . . . . . . . . . . . . . . . . . . .
Page
Starting the Engine 21. . . . . . . . . . . . . . . . . . . . . . . .
Stopping the Vehicle 21. . . . . . . . . . . . . . . . . . . . . . .
Parking the Vehicle 21. . . . . . . . . . . . . . . . . . . . . . . .
Cargo Bed 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tailgate Latches 22. . . . . . . . . . . . . . . . . . . . . . . . . .
New Vehicle Break-In 22. . . . . . . . . . . . . . . . . . . . .
Loading the Cargo Box 22. . . . . . . . . . . . . . . . . . . .
Transporting the Vehicle 23. . . . . . . . . . . . . . . . . . . .
Towing the Vehicle 23. . . . . . . . . . . . . . . . . . . . . . . .
Towing a Trailer 23. . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recommended Maintenance Schedule 24. . . . . . . . .
Daily Maintenance Checklist 25. . . . . . . . . . . . . . . .
Heavy Duty Operation 26. . . . . . . . . . . . . . . . . . . . .
Jacking the Vehicle 26. . . . . . . . . . . . . . . . . . . . . . . .
Neutral Lock Assembly 27. . . . . . . . . . . . . . . . . . . .
Servicing the Engine Oil 27. . . . . . . . . . . . . . . . . . .
Cleaning the Engine Cooling Areas 28. . . . . . . . . . .
Servicing the Air Cleaner 28. . . . . . . . . . . . . . . . . . .
Greasing the Machine 29. . . . . . . . . . . . . . . . . . . . . .
Servicing the Brakes 30. . . . . . . . . . . . . . . . . . . . . . .
Inspecting the Tires 30. . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Front Suspension 30. . . . . . . . . . . . . .
Servicing the Drive Belt 31. . . . . . . . . . . . . . . . . . . .
Adjusting the Starter Generator Belt 31. . . . . . . . . .
Adjusting Front Wheel Toe-In 32. . . . . . . . . . . . . . .
Servicing the Fuel System 32. . . . . . . . . . . . . . . . . .
Spark Plugs 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Transaxle Fluid 33. . . . . . . . . . . . . . . .
Replacing the Fuses 34. . . . . . . . . . . . . . . . . . . . . . .
Replacing the Headlights 34. . . . . . . . . . . . . . . . . . .
Servicing the Battery 34. . . . . . . . . . . . . . . . . . . . . .
Washing the Vehicle 36. . . . . . . . . . . . . . . . . . . . . . .
Electrical Schematic 37. . . . . . . . . . . . . . . . . . . . . . .
The Toro General Commercial Products Warranty 40. .
Introduction
Read this manual carefully to learn how to operate and
maintain your product properly. The information in this
manual can help you and others avoid injury and product
damage. Although Toro designs and produces safe
products, you are responsible for operating the product
properly and safely.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model and
serial numbers of your product ready. Figure 1 illustrates
the location of the model and serial numbers on the
product.

3
1m–5312
Figure 1
1. Location of the model and serial numbers
Write the product model and serial numbers in the space
below:
Model No.
Serial No.
This manual identifies potential hazards and has special
safety messages that help you and others avoid personal
injury and even death. Danger, Warning, and Caution are
signal words used to identify the level of hazard. However,
regardless of the hazard, be extremely careful.
Danger signals an extreme hazard that will cause serious
injury or death if you do not follow the recommended
precautions.
Warning signals a hazard that may cause serious injury or
death if you do not follow the recommended precautions.
Caution signals a hazard that may cause minor or moderate
injury if you do not follow the recommended precautions.
This manual uses two other words to highlight information.
Important calls attention to special mechanical
information and Note: emphasizes general information
worthy of special attention.
Safety
Improper use or maintenance by the operator or owner
can result in injury. To reduce the potential for injury,
comply with these safety instructions and always pay
attention to the safety alert symbol, which means
CAUTION, WARNING, or DANGER—“personal
safety instruction.” Failure to comply with the
instruction may result in personal injury or death.
Supervisors, operators, and service persons should be
familiar with the following standards and publications:
(The material may be obtained from the address shown).
•Flammable and Combustible Liquids Code:
ANSI/NFPA 30
•National Fire Protection Association:
ANSI/NFPA #505; Powered Industrial Trucks
National Fire Prevention Association
Barrymarch Park
Quincy, Massachusetts 02269 U.S.A.
•ANSI/ASME B56.8 Personal Burden Carriers
American National Standards Institute, Inc.
1430 Broadway
New York, New York 10018 U.S.A.
•ANSI/UL 558; Internal Combustion Engine Powered
Industrial Trucks
American National Standards Institute, Inc.
1430 Broadway
New York, New York 10018 U.S.A.
or
Underwriters Laboratories
333 Pfingsten Road
Northbrook, Illinois 60062 U.S.A.
Safe Operating Practices
The Workman is an off-highway vehicle only and
is not designed, equipped, or manufactured for use
on public streets, roads, or highways.
Warning
Supervisor’s Responsibilities
•Make sure that operators are thoroughly trained and
familiar with the Operator’s Manual and all labels on
the vehicle.
•Be sure to establish your own special procedures and
work rules for unusual operating conditions (e.g. slopes
too steep for vehicle operation).
Before Operating
•Operate the machine only after reading and
understanding the contents of this manual.
•Never allow children to operate the vehicle. Anyone
who operates the vehicle should have a motor vehicle
license.

4
•Never allow other adults to operate the vehicle without
first reading and understanding the Operator’s Manual.
Only trained and authorized persons should operate this
vehicle. Make sure that all operators are physically and
mentally capable of operating the vehicle.
•This vehicle is designed to carry only you, the operator,
and one passenger in the seat provided by the
manufacturer. Never carry any other passengers on the
vehicle.
•Never operate the vehicle when under the influence of
drugs or alcohol. Even prescription drugs and cold
medicines can cause drowsiness.
•Do not drive the vehicle when you are tired. Be sure to
take occasional breaks. It is very important that you stay
alert at all times.
•Become familiar with the controls and know how to
stop the engine quickly.
•Keep all shields, safety devices, and decals in place. If a
shield, safety device, or decal is malfunctioning,
illegible, or damaged, repair or replace it before
operating the machine.
•Always wear substantial shoes. Do not operate the
machine while wearing sandals, tennis shoes or
sneakers. Do not wear loose fitting clothing or jewelry
which could get caught in moving parts and cause
personal injury.
•Wearing safety glasses, safety shoes, long pants and a
helmet is advisable and required by some local safety
and insurance regulations.
•Avoid driving when it is dark, especially in unfamiliar
areas. If you must drive when it is dark, be sure to drive
cautiously, use the headlights, and even consider adding
additional lights.
•Be extremely careful when operating around people.
Always be aware of where bystanders might be.
•Before operating the vehicle, always check the
designated areas of the vehicle that are stated in the
pre-starting section of this manual. If something is
wrong, do not use the vehicle. Make sure that the
problem is corrected before the vehicle or attachment is
operated.
•Since gasoline is highly flammable, handle it carefully.
– Use an approved gasoline container.
– Do not remove the cap from the fuel tank when the
engine is hot or running.
– Do not smoke while handling gasoline.
– Fill the fuel tank outdoors, and fill it to about 1 in.
(25 mm) below the top of the tank (the bottom of
the filler neck). Do not overfill it.
– Wipe up any spilled gasoline.
While Operating
Engine exhaust contains carbon monoxide, which
is an odorless, deadly poison that can kill you.
Do not run engine indoors or in an enclosed area.
Warning
•The operator and passenger should remain seated
whenever the vehicle is in motion. The operator should
keep both hands on the steering wheel whenever
possible, and the passenger should use the hand holds
provided. Keep your arms and legs within the vehicle
body at all times.
•Drive slower and turn less sharply when you are
carrying a passenger. Remember your passenger may
not be expecting you to brake or turn and may not be
ready.
•Always watch out for and avoid low overhangs such as
tree limbs, door jambs, and over-head walkways. Make
sure there is enough room over head to easily clear the
vehicle and your head.
•Always shift into neutral and apply the parking brake
before leaving an idling vehicle, or else the vehicle may
creep.
•Failure to operate the vehicle safely may result in an
accident, tip over of the vehicle, and serious injury or
death. Drive carefully. To prevent tipping or loss of
control:
– Use extreme caution, reduce speed, and maintain a
safe distance around sand traps, ditches, creeks,
ramps, unfamiliar areas, or any areas that have
abrupt changes in ground conditions or elevation.
– Watch for holes or other hidden hazards.
– Use extra caution when operating the vehicle on wet
surfaces, in adverse weather conditions, at higher
speeds, or with a full load. Stopping time and
distance will increase with a full load.
– Avoid sudden stops and starts. Do not go from
reverse to forward or forward to reverse without
first coming to a complete stop.
– Slow down before turning. Do not attempt sharp
turns or abrupt maneuvers or other unsafe driving
actions that may cause a loss of vehicle control.
– When dumping, do not let anyone stand behind the
vehicle and do not dump the load on anyone’s feet.
Release the tailgate latches from the side of the box,
not from behind.
– Only operate the vehicle when the cargo box is
down and latched.

5
– Before backing up, look to the rear and ensure that
no one is behind you. Back up slowly.
– Watch out for traffic when you are near or crossing
roads. Always yield the right of way to pedestrians
and other vehicles. This vehicle is not designed for
use on streets or highways. Always signal your turns
or stop early enough so that other people know what
you plan to do. Obey all traffic rules and
regulations.
– The electrical and exhaust systems of the vehicle
can produce sparks capable of igniting explosive
materials. Never operate the vehicle in or near an
area where there is dust or fumes in the air which
are explosive.
– If you are ever unsure about safe operation, stop
work and ask your supervisor.
•Do not touch the engine or muffler while the engine is
running or soon after it has stopped. These areas may be
hot enough to cause burns.
•If the machine ever vibrates abnormally, stop
immediately, wait for all motion to stop, and inspect the
vehicle for damage. Repair all damage before
commencing operation.
•Before getting off of the seat:
A. Stop the movement of the machine.
B. Set the parking brake.
C. Turn the ignition key to Off.
D. Remove the ignition key.
Note: If the vehicle is on an incline, block the wheels after
getting off of the vehicle.
Braking
•Slow down before you approach an obstacle. This gives
you extra time to stop or turn away. Hitting an obstacle
can damage the vehicle and its contents. More
important, it can injure you and your passenger.
•Gross Vehicle Weight (GVW) has a major impact on
your ability to stop and/or turn. Heavy loads and
attachments make a vehicle harder to stop or turn. The
heavier the load, the longer it takes to stop.
•Decrease the vehicle speed if the cargo box has been
removed and there is no attachment on the vehicle. The
braking characteristics change and fast stops may cause
the rear wheels to lock up, which may affect the control
of the vehicle.
•Turf and pavement are much slipperier when they are
wet. It can take 2 to 4 times as long to stop on wet
surfaces as on dry surfaces. If you drive through
standing water deep enough to get the brakes wet, they
will not work well until they are dry. After driving
through water, you should test the brakes to make sure
they work properly. If they do not, drive slowly while
putting light pressure on the brake pedal. This will dry
the brakes out.
Operating on Hills
Operating the vehicle on a hill may cause tipping
or rolling of the vehicle, or the engine may stall
and you could lose headway on the hill. This could
result in personal injury.
•Do not exceed slopes greater than 12.
•Do not accelerate quickly or slam on the brakes
when backing down a hill, especially with a load.
•If the engine stalls or you lose headway on a hill,
slowly back straight down the hill. Never
attempt to turn the vehicle around.
•Never drive across a steep hill; always drive
straight up or down or go around the hill.
•Avoid turning on a hill.
•Reduce your load and the speed of the vehicle.
•Avoid stopping on hills, especially with a load.
Warning
These extra cautions need to be taken when operating the
vehicle on a hill:
•Slow down before starting up or down a hill.
•If the engine stalls or you begin to lose headway while
climbing a hill, gradually apply the brakes and slowly
back straight down the hill.
•Turning while traveling up or down hills can be
dangerous. If you have to turn while on a hill, do it
slowly and cautiously. Never make sharp or fast turns.
•Heavy loads affect stability. Reduce the weight of the
load and your speed when operating on hills or if the
load has a high center of gravity. Secure the load to
prevent it from shifting.
•Avoid stopping on hills, especially with a load.
Stopping while going down a hill will take longer than
stopping on level ground. If the vehicle must be
stopped, avoid sudden speed changes, which may
initiate tipping or rolling of the vehicle. Do not slam on
the brakes when rolling backward, as this may cause the
vehicle to overturn.
•Travel straight up and down slopes whenever possible.
•We strongly recommend installing the optional ROPS
Kit when operating on hilly terrain.

6
Operating on Rough Terrain
Reduce speed and load when operating on rough terrain,
uneven ground, and near curbs, holes, and other sudden
changes in terrain. Loads may shift, causing the vehicle to
become unstable.
We strongly recommend installing the optional ROPS Kit
when operating on rough terrain.
Sudden changes in terrain may cause abrupt
steering wheel movement, possibly resulting in
hand and arm injuries.
•Reduce your speed when operating on rough
terrain and near curbs.
•Grip the steering wheel loosely around the
perimeter. Keep your hands clear of the steering
wheel spokes.
Warning
Loading and Dumping
The weight and position of the cargo and passenger can
change the vehicle center of gravity and vehicle handling.
To avoid loss of control and personal injury, follow these
guidelines:
•Do not carry loads which exceed the load limits
described on the vehicle weight label; refer to
Specifications, page 13, for vehicle weight limits. The
load rating is for level surfaces only.
•Reduce the weight of the load when operating on hills
and rough terrain to avoid tipping or overturning of the
vehicle.
•Reduce the weight of the load if the center of gravity is
high. Items such as bricks, fertilizer, or landscape
timbers stack higher in the box. The higher a load is
stacked, the more likely the vehicle is to tip over.
Distribute the load as low as possible, making sure that
the load does not affect rear visibility.
•Position the weight of the load evenly from side to side.
If you position the load toward one of the sides, the
vehicle is more likely to tip over while turning.
•Position the weight of a load evenly from front to back.
If you position the load behind the rear axle, it will
reduce the weight on the front wheels. This may result
in a loss of steering control or cause the vehicle to tip
over on hills or bumpy terrain.
•Use extra caution if the load exceeds the dimensions of
the box and when handling off-center loads that cannot
be centered. Keep loads balanced and secure to prevent
them from shifting.
•Always secure loads so that they do not shift. If a load
is not secured, or you are transporting a liquid in a large
container such as a sprayer, the load can shift. This
shifting happens most often while turning, going up or
down hills, suddenly changing speeds, or while driving
over rough surfaces. Shifting loads can cause the
vehicle to tip over.
The weight of the box may be heavy. Hands or
other body parts could be crushed.
•Keep hands and other body parts clear when
lowering the box.
•Do not dump materials on bystanders.
Warning
•Never dump a loaded cargo box while the vehicle is
sideways on a hill. The change in weight distribution
may cause the vehicle to overturn.
•When operating with a heavy load in the cargo box,
reduce your speed and allow for sufficient braking
distance. Do not suddenly apply the brakes. Use extra
caution on slopes.
•Be aware that heavy loads increase your stopping
distance and reduce your ability to turn quickly without
tipping over.
•The rear cargo space is intended for load carrying
purposes only, not for passengers.
•Never overload your vehicle. The name plate (located
under dash on center column) shows load limits for the
vehicle. Never overload the attachments or exceed the
Gross Vehicle Weight (GVW).
Maintenance
•Only qualified and authorized personnel shall be
permitted to maintain, repair, adjust, or inspect the
vehicle.
•Before servicing or making adjustments to the machine,
stop the engine, set the parking brake, and remove the
key from the ignition to prevent someone from
accidentally starting the engine.
•To make sure that the entire machine is in good
condition, keep all nuts, bolts, and screws properly
tightened.
•To reduce the potential for fire, keep the engine area
free of excessive grease, grass, leaves, and
accumulation of dirt.
•Never use an open flame to check the level or leakage
of fuel or battery electrolyte.

7
•If the engine must be running to perform a maintenance
adjustment, keep your hands, feet, clothing, and any
parts of your body away from the engine and any
moving parts. Keep everyone away.
•Do not use open pans of fuel or flammable cleaning
fluids for cleaning parts.
•Do not adjust the ground speed governor. To ensure
safety and accuracy, have an Authorized Toro
Distributor check the ground speed.
•If major repairs are ever needed or assistance is
required, contact an Authorized Toro Distributor.
•To be sure of optimum performance and safety, always
purchase genuine Toro replacement parts and
accessories. Replacement parts and accessories made by
other manufacturers could be dangerous. Altering this
vehicle in any manner that may affect vehicle operation,
performance, durability, or its use, may result in injury
or death. Such use could void the product warranty.
Sound Pressure Level
This unit has an equivalent continuous A-weighted sound
pressure at the operator ear of 80 dB(A) based on
measurements of identical machines per SAE J1174-MAR
85 procedures.
Vibration Level
This unit does not exceed a vibration level of 2.5 m/s2at
the hands based on measurements of identical machines per
ISO 5349 procedures.
This unit does not exceed a vibration level of 0.5 m/s2at
the posterior based on measurements of identical machines
per ISO 2631 procedures.

8

9
Slope Chart
ALIGN THIS EDGE WITH A VERTICAL SURFACE
(TREE, BUILDING, FENCEPOST, POLE, ETC.)
FOLD ALONG APPROPRIATE LINE.
EXAMPLE: COMPARE SLOPE WITH FOLDED EDGE.

10

11
Safety and Instruction Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or lost.
99-7350
1. Maximum tongue weight
is 50 lb. (23 kg) 2. Maximum trailer weight is 400 lb. (181 kg)
99-7348
1. Read the operator’s manual for further instructions.
2. The maximum combined operator and passenger weight
should not exceed 400 lb. (181 kg).
3. The maximum cargo weight should not exceed 1250 lb.
(567 kg).
4. The base weight of the vehicle is 1000 lb. (454 kg).
5. The maximum gross vehicle weight should not exceed 2650 lb.
(1202 kg).
99-7349
1. Unlock cargo bed 2. Lock cargo bed
99-7346
1. Parking brake
2. Parking brake on 3. Parking brake off
99-7347
1. Choke
2. Reverse 3. Forward
99-7954
1. Danger—read the operator’s manual.
2. Do not carry passengers in the cargo bed. They may fall out.
3. Explosive hazard—remove fuel containers from the cargo bed
before filling.

12
99-7343
1. Warning—read the operator’s manual.
2. Only drive this vehicle off-highway. This vehicle is not made for use on public streets, roads, or highways.
3. Do not carry passengers in the cargo bed. They may fall out of the vehicle.
4. Do not allow children to operate this vehicle.
5. Hour meter
6. Headlights
7. Ignition off
8. Ignition on
9. To start the vehicle, sit in the operator’s seat. Release the parking brake. Turn the ignition on. Pull the choke lever out (if needed). Depress
the accelerator.
10. To stop the vehicle, disengage the accelerator and engage the parking brake. Turn the ignition off and remove the key.
11. Power point
99-7344
1. Danger—read the operator’s manual.
2. Fuel is flammable. Stop the engine before adding fuel.
3. Tipping hazard—do not drive across slopes that are greater than 15 degrees or up slopes greater than 12 degrees. Reduce speed when
turning, carrying heavy loads, or driving on rough terrain. Keep the engine speed under 16 MPH (26 km/h).
4. Passengers are at risk of falling from the vehicle. Do not carry passengers in the cargo bed. Keep arms and legs inside of the vehicle at all
times.
99-7345
1. Danger—read the operator’s manual.
2. Hot surface hazard—keep hands away.
3. Entanglement hazard—stay away from moving parts.
4. Crushing hazard—use the prop rod to support the cargo bed.
26-7390

13
99-7352
1. Read the operator’s
manual for information on
fuses.
2. 10 amp. fuse for optional
Road Light Kit
3. 15 amp. fuse for optional
Rear Lift Kit
4. 10 amp. fuse—open
5. 10 amp. fuse for
headlights
6. 10 amp. fuse for ignition
system
7. 15 amp. fuse for optional
Electric Bed Lift Kit
Specifications
Note: Specifications and design are subject to change without notice.
Base weight Dry 1000 lb. (454 kg)
Rated capacity
(on level ground) 1650 lb. (749 kg) total, including 200 lb. (90.7 kg) operator and 200 lb. (90.7 kg)
passenger, load, trailer tongue weight, gross trailer weight, accessories, and
attachments
Maximum gross vehicle
weight (GVW)
(on level ground)
2650 lb. (1203 kg) total, including all of the weights listed above
Maximum cargo capacity
(on level ground) 1250 lb. (567 kg) total, including trailer tongue weight and gross trailer weight
Tow capacity:
Standard Hitch Tongue weight 50 lbs. (23 kg) Maximum trailer weight 400 lbs. (182 kg)
Heavy Duty Hitch Tongue weight 100 lbs. (45 kg) Maximum trailer weight 800 lbs. (363 kg)
Overall width 60 in. (152.4 cm)
Overall length 117 in. (297.2 cm)
Ground clearance 9-1/4 in. (23.5 cm) at the front with no load or operator
6-1/2 in. (16.5 cm) at the rear with no load or operator
Wheel base 79 in. (200.7 cm)
Wheel tread
(center line to center line) 49 in. (124.5 cm) in the front
48-1/4 in. (122.6 cm) in the rear
Cargo box length 46 in. (116.8 cm) inside
51 in. (129.5 cm) outside
Cargo box width 49 in. (124.5 cm) inside
54 in. (137.2 cm) outside
Cargo box height 10 in. (25.4 cm) inside

14
Setup
Note: Determine the left and right sides of the machine from the normal operating position.
Loose Parts
Note: Use the chart below to verify that all parts have been shipped.
Description Qty. Use
Wheel assembly 2Installing the rear wheels (Model No. 07253TC)
Wheel assembly
Washer
Dust cap
2
2
2Installing the front wheels (Model No. 07253TC)
Steering wheel 1Installing the steering wheel (Model No. 07253TC)
Bumper 1 Installing the bumper (Model No. 07253TC)
Hitch 1 Installing the hitch (Model No. 07253TC)
Seat 2 Installing the seats (Model No. 07253TC)
Cargo box
Right-hand pivot bracket
Left-hand pivot bracket
Prop rod clip
Flange head screw, 3/8 x 1 in.
Screw, 5/16 x 3/4 in.
1
1
1
1
4
2
Installing the cargo box (Model No. 07253TC)
Key 2 Use in the ignition switch.
Operator’s Manual
Engine Operator’s Manual 1 1Read before operating the machine.
Operator Video 1Watch before operating the machine.
Parts Catalog 1Use for ordering replacement parts.
Registration Card 1Complete and return to Toro.
Predelivery Inspection Form 1Complete and file in your customer history portfolio.

15
Installing the Rear Wheels
Note: This procedure is only needed for Model No.
07253TC.
1. Remove the fasteners securing the wheels.
2. Remove the shipping bracket secured to the wheel
studs.
3. Mount the wheels with the previously removed
fasteners (Fig. 2) and torque to 45–65 ft.-lb.
(61–88 N⋅m).
1
2
3
Figure 2
1. Wheel assembly
2. Wheel nut 3. Wheel stud
Installing the Front Wheels
Note: This procedure is only needed for Model No.
07253TC.
1. Remove the fasteners securing the wheels.
2. Remove the shipping bracket from the spindles.
3. Apply Loctite (blue) to the screw threads.
4. Mount the wheels with the previously removed
fasteners (Fig. 3) and torque the bolts to 135–165 ft.-lb.
(183–224 N⋅m)
1
24
3
5
6
Figure 3
1. Tire and wheel assembly
2. Spindle
3. Small washer
4. Large washer
5. Screw
6. Dust cap
Installing the Steering Wheel
Note: This procedure is only needed for Model No.
07253TC.
1. Remove the nut and lock washer from the steering
shaft.
2. Slide the steering wheel and washer onto the shaft.
Position the steering wheel on the shaft so that the cross
beam is horizontal when the tires are pointed straight
ahead and the thicker spoke of the steering wheel is
downward.
3. Secure the steering wheel to the shaft with the nut
(Fig. 4).
1
2
3
4
Figure 4
1. Steering wheel
2. Nut 3. Washer 4. Foam seal

16
Installing the Bumper
Note: This procedure is only needed for Model No.
07253TC.
1. Remove the 2 bolts, washers, and nuts secured to the
front of the frame.
2. Align the mounting holes and secure the bumper to the
frame with the fasteners previously removed (Fig. 5).
1
Figure 5
1. Bumper
Installing the Seats
Note: This procedure is only needed for Model No.
07253TC.
Insert the seat bracket into the seat base opening and pivot
the seat downward (Fig. 6).
1
2Figure 6
1. Seat bracket 2. Seat base
Installing the Hitch
Note: This procedure is only needed for Model No.
07253TC.
1. Remove the 4 bolts and nuts from the inside rear of the
frame.
2. Align the hitch with the mounting holes on the frame.
Secure the hitch with the screws and nuts (Fig. 7).
1
Figure 7
1. Hitch
Installing the Cargo Box
Note: This procedure is only needed for Model No.
07253TC.
1. Position the cargo box onto the frame. The cargo box
must lay flat and be centered.
2. Mount the left hand pivot bracket to the left rear corner
of the frame with 2 flange head screws (3/8 x 1 in.).
Position the bracket as shown in Figure 8.
1
Figure 8
1. Pivot bracket
3. Slide the cargo box mounting hole onto the pivot
bracket (Fig. 9).

17
1
3
2
Figure 9
1. Cargo box
2. Pivot bracket 3. Cargo box mounting hole
4. Insert the right hand pivot bracket into the mounting
hole in the cargo box and then mount it to the frame.
5. Have another person help to raise the cargo box until
the “J” hook end of the prop rod is positioned between
the 2 holes on the left frame rail (Fig. 10).
1
2
Figure 10
1. Prop rod 2. Prop rod clip
6. Secure the prop rod to the frame rail with the prop rod
clip and 2 screws (5/16 x 3/4 in.) (Fig. 10).
7. Lower the cargo box.
Activating the Battery
Note: This procedure is only needed for Model No.
07253TC.
If the battery is not filled with electrolyte or activated, it
must be removed from the vehicle, filled with electrolyte,
and charged. Bulk electrolyte with 1.260 specific gravity
must be purchased from a local battery supply outlet.
1. Remove the rubber strap securing the battery to the
battery base. Lift the battery out of the battery base.
Danger
Battery electrolyte contains sulfuric acid which is a
deadly poison and causes severe burns.
•Do not drink electrolyte and avoid contact with
skin, eyes or clothing. Wear safety glasses to
shield your eyes and rubber gloves to protect
your hands.
•Fill the battery where clean water is always
available for flushing the skin.
2. Remove the filler caps from the battery and slowly fill
each cell until electrolyte is just above the plates.
3. Replace the filler caps and connect a 3 to 4 amp. battery
charger to the battery posts. Charge the battery at a rate
of 3 to 4 amperes for 4 to 8 hours (12 volts). Do not
overcharge the battery.
Charging the battery produces gasses that can
explode.
Never smoke near the battery and keep sparks and
flames away from battery.
Warning
4. When the battery is charged, disconnect the charger
from the electrical outlet and battery posts.
5. Remove the filler caps. Slowly add electrolyte to each
cell until electrolyte is up to the fill line. Install the filler
caps.
Important Do not overfill the battery. Electrolyte will
overflow onto other parts of the vehicle and severe
corrosion and deterioration will result.
6. Install the battery; refer to Installing the Battery,
page 35.

18
Checking the Crankcase Oil
The engine is shipped with oil in the crankcase; however,
the level of oil must be checked before and after the engine
is first started.
1. Position the machine on a level surface.
2. Remove the dipstick and wipe it with a clean rag
(Fig. 11). Insert the dipstick into the tube and make sure
it is seated fully. Remove the dipstick and check the oil
level.
1
2
Figure 11
1. Dipstick 2. Filler cap
3. If the oil level is low, remove the filler cap from the
valve cover (Fig. 11) and pour oil into the opening until
the oil level is up to the Full mark on the dipstick; refer
to Engine Oil, page 27, for the proper oil type and
viscosity. Add the oil slowly and check the level often
during this process. Do not overfill.
4. Install the dipstick firmly in place.
Checking the Tire Pressure
Check the tire pressure every 8 hours or daily to ensure
proper levels.
The air pressure range in the front and rear tires is 8–22 psi
(55–152 kPa).
The air pressure needed is determined by the payload
carried. The lower the air pressure, the less the compaction
and tire marks are minimized. Lower pressure should not
be used for heavy payloads at high speeds.
Higher pressures should be used for heavier payloads at
higher speeds. Do not exceed the maximum pressure.
Fuel Tank
Recommended Gasoline
Use fresh, clean, unleaded regular gasoline suitable for
automotive use (85 pump octane minimum). Leaded
gasoline may be used if unleaded regular is not available.
Important Never use gasoline containing methanol,
gasoline containing more than 10% ethanol, gasoline
additives, or white gas because engine fuel system damage
could result.
Danger
In certain conditions, gasoline is extremely
flammable and highly explosive. A fire or
explosion from gasoline can burn you and others
and can damage property.
•Fill the fuel tank outdoors, in an open area,
when the engine is cold. Wipe up any gasoline
that spills.
•Do not fill the fuel tank completely full. Add
gasoline to the fuel tank until the level is 1 in.
(25 mm) below the bottom of the filler neck.
This empty space in the tank allows gasoline to
expand.
•Never smoke when handling gasoline, and stay
away from an open flame or where gasoline
fumes may be ignited by a spark.
•Store gasoline in an approved container and
keep it out of the reach of children. Never buy
more than a 30-day supply of gasoline.
•Always place gasoline containers on the ground
away from your vehicle before filling.
•Do not fill gasoline containers inside a vehicle or
on a truck or trailer bed because interior
carpets or plastic truck bed liners may insulate
the container and slow the loss of any static
charge.
•When practical, remove gas-powered equipment
from the truck or trailer and refuel the
equipment with its wheels on the ground.
•If this is not possible, then refuel such
equipment on a truck or trailer from a portable
container, rather than from a gasoline dispenser
nozzle.
•If a gasoline dispenser nozzle must be used, keep
the nozzle in contact with the rim of the fuel
tank or container opening at all times until
fueling is complete.

19
Filling the Fuel Tank
Fuel tank capacity is approximately 7 gallons.
1. Shut the engine off and set the parking brake.
2. Clean the area around the fuel tank cap (Fig. 12).
1
Figure 12
1. Fuel tank cap
3. Remove the fuel tank cap.
4. Fill the tank to about one inch below the top of the tank,
(bottom of the filler neck). This space in the tank allows
gasoline to expand. Do not overfill.
5. Install the fuel tank cap securely. Wipe up any fuel that
may have spilled.
Operation
Note: Determine the left and right sides of the machine
from the normal operating position.
Think Safety First
Please carefully read all of the safety instructions and
decals in the safety section. Knowing this information
could help you or bystanders avoid injury.
Controls
Accelerator Pedal
The accelerator pedal (Fig. 13) gives the operator the
ability to vary ground speed of the vehicle. Depressing the
pedal starts the engine. Depressing the pedal farther
increases ground speed. Releasing the pedal will slow the
vehicle and the engine will stop running. Maximum
forward speed is 16 MPH (26 km/h).
Brake Pedal
The brake pedal is used to stop or slow the vehicle
(Fig. 13).
Brakes can become worn or can be misadjusted
resulting in personal injury.
If brake pedal travels to within 1of the vehicle
floor board, the brakes must be adjusted or
repaired.
Caution
Parking Brake
The parking brake is a small plate at the top of the brake
pedal (Fig. 13). Whenever the engine is shut off, the
parking brake must be engaged to prevent accidental
movement of the vehicle. To engage the parking brake, step
on the brake pedal firmly and roll forward with the top of
your foot. To disengage, depress the accelerator pedal. If
the vehicle is parked on a steep grade, make sure that the
parking brake is applied. Place blocks at the downhill side
of the wheels.
1
m–5313
2
3
Figure 13
1. Accelerator pedal
2. Brake pedal 3. Parking brake
Choke Control
The choke control is located below and to the right of the
operator’s seat. To start a cold engine, close the carburetor
choke (Fig. 14) by pulling the choke control outward to the
On position. After the engine starts, regulate the choke to
keep the engine running smoothly. As soon as possible,
open the choke by pushing the control in to the Off
position. A warm engine requires little or no choking.

20
1
2
Figure 14
1. Choke 2. Gear shift selector
Gear Shift Selector
The gear shift selector moves the vehicle in the desired
direction—forward or reverse (Fig. 14). The vehicle will
start in either direction.
Note: If the gear shift selector is in Reverse when the
ignition is turned on, a buzzer will sound to warn the
operator.
Important The vehicle should always be stopped
before changing the gear selection and direction.
Ignition Switch
The ignition switch (Fig. 15), used to start and stop the
engine, has two positions: Off and On. Rotate the key
clockwise to the On position to allow operation. When the
vehicle is stopped, rotate the key counterclockwise to the
Off position. Remove the key from the ignition.
Hour Meter
The hour meter (Fig. 15) indicates the total number of
hours the engine is running. The hour meter starts to
function whenever the accelerator is depressed.
Oil Light
The oil light warns the operator if the engine oil pressure
drops below a safe level (Fig. 15). If the light comes on and
remains lit, the oil level should be checked and oil added if
necessary; see Engine Oil, page 27.
Note: The oil light may flicker. This is normal and no
action needs to be taken.
Light Switch
Toggle the switch to activate the headlights. Push it to turn
the lights on (Fig. 15).
Power Point
The power point is used to power optional electrical
accessories (Fig. 15).
12
34
5m–4885
Figure 15
1. Ignition switch
2. Hour meter
3. Light switch
4. Oil light
5. Power Point
Fuel Gauge
The fuel gauge (Fig. 16) shows the amount of fuel in the
tank.
1
Figure 16
1. Fuel gauge