Tranberg TEF 2441 User manual

Tranberg AS | P.O. Box 8033 | N-4068 Stavanger | Norway | Tel.: [phone] | Fax.: [phone]
E-mail: [email protected] | www.tranberg.com
Tranberg Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: [phone]
E-mail: [email protected] | www.tranbergsystems.com
TEF 2441
LUMINAIRE USER MANUAL
IMPORTANT
Read this instruction carefully before installing the
luminaire
240A4831
TUM 1009 Rev. A 03.01.17

TEF 2441 LUMINAIRE USER MANUAL
INTRODUCTION
Thank you for purchasing this product!
For installation, maintenance and assurance of a long life
of this product, please follow this manual.
CONTENT IN BOX
The product is fully assembled, and ready for installation.
SAFETY PRECAUTIONS
Note that changes made to the product and/or installation
of components which do not conform to the approval,
may be a safety violation. The manufacturer will in no
circumstance be held responsible for such activity.
For your health and safety, always use safety gear suited
for the task. Be certain to follow codes, regulations and/or
specific procedures that are related to the installation.
TOOLS REQUIRED
Regular tools required for installation:
• 10mm wrench - when installing the luminaire.
• 32mm wrench - when installing the cable gland
• 30mm wrench - when installing the lock nut.
• 25mm wrench –when tightening the pressure nut.
• PZ 2 screwdriver for assemble/dissemble the globe
• 3mm straight screwdriver for terminal to connect the
lighting.
• 5mm straight screwdriver for earth screw.
Do not use powertools when fastening globe!
MAINTENANCE INSTRUCTIONS
The luminaire should be inspected according to Company
routines. The manufacturer suggests regular check for
water intrusion/condensation which should be removed
immediately. Check the drain plug / drain hole function.
When cleaning, use only mild detergents. Alcohol or
petroleum based products may damage lens, paint or
plastic components.
ELECTRICAL INSTALLATION
The luminaire is factory configured with grommet kit 3C, suitable for cable diameters ranging from 8.5 mm to 13.5 mm. For
cable diameters ranging from 13.0 mm to 17.0 mm, please ensure to replace the installed grommet kit with kit 3D. Cable
entries should be tightened properly. Do not use execessive force, as this may disalign the grommet components and lead
to water intrusion.
Make sure electrical connections are safe and reliable.
RUBBER SEAL
Cable diameter Size Part No.
8,5 - 13,5mm Ø23/13x8mm 5002 0124
13 - 17mm Ø23/16x8mm 5002 0125
Be sure to install the cable in a way wich prevents water to penetrate into the enclosure through the cable gland,
Also make sure to use the correct rubber seal when you install the luminaire
APPLICATIONS
• Signal lighting
• Obstacle marking
APPROVALS
NA

TEF 2441 LUMINAIRE USER MANUAL
Before replacing the globe assembly, please review the fol-
lowing:
• Verify thatthegrommetkitused matchthe cablediameter.
• Cables should have a bend before entering the cable
gland, which will avoid water intrusion into the luminaire.
• An unused cable gland should be replaced with a blind
plug.
Ensure the globe gasket is clean and properly aligned
around the bottom of the globe. Then carefully position
the globe over the PL-C light source and into the circular
opening in the luminaire base. Slightly tighten two opposite
screws, then repeat with the other two opposite screws.
This ensures that the globe is positioned evenly and the
pressure on the globe gasket is distributed evenly. Tighten
all four screws until the globe is firmly positioned. Power
tools should under no circumstances be used!
WIRING DIAGRAM
COMPLETE THE INSTALLATION

Tranberg AS | P.O. Box 8033 | N-4068 Stavanger | Norway | Tel.: [phone] | Fax.: [phone]
E-mail: [email protected] | www.tranberg.com
Tranberg Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: [phone]
E-mail: [email protected] | www.tranbergsystems.com
TEF 2441 LUMINAIRES USER MANUAL
TECHNICAL DATA
Material: Acid proof stainless steel, powder coated RAL 9010
Globe : Polycarbonate
Light output: >10 candela red
Power comsumption: Max. 20 Watt
IP-rating: IP66
Standard cable entries: 3 x M25 stopping plug
Weight: 3,8 kg.
Tamb: -20°C to +40°C
For use in zone: Safe area
SPARE PARTS
Description Part No.
Globe red, without gasket 5044 2006
Globe gasket, silicone 5001 0021
Globe retainer ring 2547
Fluorescent tube, PLC 13W/84 9400 060
Cable gland, E704/CD/M25 9147 200
Stopping plug, M25 EExe 7947 304
Drain plug with lock nut, M25 EExe 7302 106