Tranberg TEF 2940 User manual

R. Stahl Tranberg AS
E[email protected] | stahl-tranberg.com
Main office: Strandsvingen 6 | N-4032 Stavanger | Norway | T+47 51 57 89 00 | F+47 51 57 89 50
Office Oslo: Luhrtoppen 2 | N-1470 Lørenskog |Norway | T+47 24 08 44 10
IMPORTANT
Read this instruction carefully before installing the
product
NAVIGATION LIGHTS
TEF 2940 MARKING LIGHT
SAFE AREA
USER MANUAL
Subject to change without prior notice TUM1021 REV. A 17.07.2017

TEF 2940 MARKING LIGHT USER MANUAL
INTRODUCTION
Thank you for purchasing this product!
For installation, maintenance and assurance of a long life
of this product, please follow this manual.
CONTENT IN BOX
The product is fully assembled, and ready for installation.
SAFETY PRECAUTIONS
Note that changes made to the product and/or installation
of components which do not conform to the approval,
may be a safety violation. The manufacturer will in no
circumstance be held responsible for such activity.
For your health and safety, always use safety gear suited
for the task. Be certain to follow codes, regulations and/or
specific procedures that are related to the installation.
TOOLS REQUIRED
Regular tools required for installation:
• 13 mm wrench –for assembling the luminaire with or
without grip for 2” pipe grip.
• 6,5 mm flat screwdriver –for cover for terminal box,
earth screw and drain screw in the cover.
• 19 mm wrench –for changing the drain-/blind plug.
• 27 mm wrench –for the cable gland.
• 24 mm wrench –for tightening the pressure nut.
MAINTENANCE INSTRUCTIONS
The light should be inspected according to Company
routines. The manufacturer suggests regular check for
water intrusion/condensation which should be removed
immediately. Check the drain plug / drain hole function.
When cleaning, use only mild detergents. Alcohol or
petroleum based products may damage lens, paint or
plastic components.
APPLICATIONS
• Bridges
• Harbours
• Etc.
RUBBER SEAL
Cable diameter Size Part No.
5 - 9mm Ø20,4/9,0x8mm 5002 0045
8,5 - 14mm Ø20,5/13,0x8mm 5002 0038
Be sure to install the cable in a way wich prevents water to penetrate into the enclosure through the cable gland,
also make sure to use the correct rubber seal when you install the luminaire
PRESSURE RING
Size Part No.
Ø20,5 x 13,1 x 1mm 5079 9023
Ø20,5 x 15 x 1mm 5079 9022
APPROVAL
NA

TEF 2940 MARKING LIGHT USER MANUAL
INSTALLATION INSTRUCTIONS
The lantern should be installed according to IMO regulations
and other relevant rules and regulations for electrical
installations onboard ships.
Consider the difference in material between the lantern
(seawater resistant aluminium or brass) and the wall/mast it
is to be installed on. Use galvanic isolators whenever there
is a risk of corrosion.
Important!
The fixing screws or bolts must be tightened firmly (for
all round lantern illustrated with max. 2,5 kg/m with an
adjustable torque wrench), but excessive force will damage
the lantern. It is recommended to use stainless steel screws/
bolts.
Important!
If Tranberg stainless steel mounting bracket is used for
mounting the all round lantern, the fixing hoop nuts must
be tightened firmly (illustrated with max. 2,5 kg/m with an
adjustable torque wrench), but excessive force will bend the
bracket, and bolt the bracket and the fixing threads in the
lantern will be damaged.
The power cable should enter the lantern in such a manner
that the cable gland correctly forms a tight entrance. The
cable must be clamped near up to the lantern according
to relevant rules and regulations for electrical installations
onboard ships
SPARE PART LIST TEF 2870MS
Description Rart No.
Glass lens, clear 5048 0027
Glass lens, green 5048 1018
Glass lens, red 5048 2018
Lamp holder, E27 5087 0011
Light source 230V / 60W signal bulb 9400 029
Light source 230V / 15W Energy efficient light bulb
Light source 230V / 60W Incandescent bulb
Silicone 2000 015
Mounting bracket 1” 0000 2600
Mounting bracket 2” 0000 2440
Flasher control with change-over and alarm 4100 000
cable gland M20 7045 043

R. Stahl Tranberg AS
E[email protected] | stahl-tranberg.com
Main office: Strandsvingen 6 | N-4032 Stavanger | Norway | T+47 51 57 89 00 | F+47 51 57 89 50
Office Oslo: Luhrtoppen 2 | N-1470 Lørenskog |Norway | T+47 24 08 44 10
TEF 2940 MARKING LIGHT USER MANUAL
TECHNICAL DATA
Material: Cast brass, Lens of through-coloured glass
Input voltage: 220-240V AC 50/60Hz
Light sources: Incandescent lamp. Signal lamp max. 60W. Energy efficient bulb
Lamp holder: E27
Power comsumption: 15-60 Watt, depandant on light source
Minimum visibility: 6 n. m. with clear lens
3 n.m. with coloured lens
Weight: 2,85 kg.
Ingress protection: IP56
Standard cable entries: M20 (cable diam.: 5-14mm)