TriBrer Lemon 5 User manual

Lemon 5

1
Any undefined changeor modification ofthis manual willdeprive you ofthe right tooperate the equipment.
Toreduce the riskof fire orelectric shock, donot expose theequipment to rainor humidity.
Toprevent electric shock,please do notopen the shell,and it mustbe repaired byqualified personnel.
This product isdesigned for splicingthe glass fiberof optical communicationsand cannot beused to spliceother materials.
Toreduce the riskof fire orelectric shock, donot allow liquidsuch as wateror metallic substancesto enter themachine.
It is forbiddento use thefusion splicer inthe flammable andexplosive environment, otherwiseit will leadto fire orexplosion.
When the fusionsplicer is working,do not touchthe electrode, avoidthe hurt causedby the dischargeof the electrode.
When replacing theelectrode, you mustturn off thepower and disconnectthe power cord.
Please follow theoperation manual strictlyto use thebattery:
*Please do notcharge the batteryby using methodsother than inthe manual;
* Don't throwthe battery intothe fire;
* Don't reversepositive and negativepoles;
* Do notcharge or dischargeunder high temperature,fire or directsunlight;
* Do notthrow or impactthe battery;
* If thebattery electrolyte leaksout, please handleit carefully.If you contactthe skin oreyes accidentally, pleasemust clean itthoroughly and seekmedical
advice immediately.Please also inform the maintenancecenter of handling the battery.
Warning

2
Cautions
Do not useand store thefusion splicer ina high temperatureand humidity environment.Otherwise, it may causedamage to the equipment.
Do not touchthe heat-shrinkable tubeduring the heatingor just ending,because the heatshrink is hotand may causeburns.
Do not touchthe fusion splicer, ACpower cord andAC plugwhen wet hand,otherwise it maycause electric shock.
Do not useany chemicals otherthan alcohol toclean microscope lenses,V-grooves, LCDscreen, etc., otherwise itmay cause blurred images,stains, etc.,
and may evencause equipment's corrosion and damage.
In the dustyenvironment, dust-proof measuresmust be takento prevent dustfrom entering the machine and causingtrouble.
Do not allowthe fusion splicerto be subjectedto strong vibrationand shocks, otherwisethe machine will bedamaged.
Please use adedicated carrier totransport or storethe fusion splicer.
Using the battery:
The equipment canuse a disposablealkaline battery orrechargeable battery,and cannot bemixed with different typesor different capacity batteries.Only
rechargeable batteries canbe charged.
Avoiding condensation:
Sudden changes intemperature should beavoided. Do notuse the deviceimmediately after moving the devicefrom the cold area to thehot area, orwhen
the room suddenlyheats up, because the devicemay have condensationphenomenon. If the temperature changes abruptly, stop using itand take outthe
battery, andthe power canbe switched onafter at leastan hour.
Storage:
When the deviceis not usedfor a longtime, please takeout the batteryto avoid thedamage caused by batteryleakage.
All is subjectedto the physicalproducts, the manualhere is justonly for reference.

Standard Package
3
Carrying case
Spare electrode
Cooling tray Calibration certificate
Fiber cleaver
Fiber stripper
AC/DC adapter
CD

1
2
5
6
3
4
11
12
14
15
16
17
Objective lens
Electrode
Charging port
Removable battery
Anti-collision batten
8Heater V-groove
V-groove
Clamp slot
Hand strap
USB port
4.3 inchTFT colorLCD
7Electrode Cover
LED
10 Multi-function clamp
9Heater cover
Optical fiberpresser
13
Windshield cover
4
9
10
12
3
4
5
6
7
8
11
18 OPM/VFL port
18
16 15
14
12
13
17
19
19 Screen Cover
Host

Power On/Off
Enter intomain menu
Start heating
Motor reset
Navigation buttons
Move thecursor/fiber
Modify settings
Start splicing
5
Enter
Save settings
Save spliceimage
Switch X/Yimages
Discharge
How toUse Keyboard
Back toprevious menu
Note:Also canbe operatedby touchscreen.

Note: Place fiberbetween electrodes tipand V-grooveend.
Hold Pull
Marking
6
Turn on
Placing protectionsleeve overfiber
Stripping, Cleaningand Cleavingfiber
Loading fiberonto splicer
Confirming splicingmode, automaticsplicing
when windshieldcover closed
Visual inspectionon LCD duringsplice
Tension Test
Splicing Operation
Taking outspliced fiber
Centering sleeveto splicedpoint
Centering sleevein heater
Start heating
Press " " tosave thesplice image
HEAT

7
Press " " to turnon thedevice, thenenter intothe " READY" interface indefault, anddisplay thepresent
splice andheat modesettings.
52%
READY

OPM VFLFunction
In " READY" interface, press " " to enterOPM/VFL measurementinterface, thentap correspondingicons
to operate.Andpress " " to backto " READY" Interface.
Set referencevalue
Switch unitdBm/dB
/Blink/OFF
Wavelength 850/1300/1310/1490/1550/1625nm
Ref setting
Unit
VFL ON
8

9
Press " " to enterthe mainmenu, thenusing navigationbuttons tochoose thedifferent sub-menus,
and press " " to entereach interface,then press " " back tomain menu.
Main Menu
52%

Splice Mode
10
In "Splice Mode" ,user canpress " " / " "to choose, and " " to directlyuse theselected
splice mode,then itturns redwhen selected.
52%

Splice Mode
11
Press " " / " " and " " to editsplicing parametersin eachfiber typeoption, then " " / " "
to modifythe parameter.
Note: Donot modifythe parametersat will.
52%
Set the pre-discharge time before final splicing
Set pre-discharge power before final splicing
Set splicing time
Set splicing power
Set the distance of left and right fiber end face
Set the limit value of fiber end surface angle
Core/ProfileAlignment
Set the overlap length of fiber propel when splice
.

Heat Mode
12
In " Heat Mode" , usercan selectprotection sleevelength basedon requirement.Then press " " to enter
parameter editioninterface toset heattime, temperatureand autoheat ON/OFF.
52%
52%
Range: 0-240s
Range: 130-200
Open/Close

52%
13
Function Settings
In FunctionSettings, press " " / " " to choose,and " " to editON/OFF foreach function.
If "Open", it will auto splicing when close the cover
If "Open", it will auto-reset the motor after splicing
Open/Close auto arc calibration after splicing
If "Open" ,it will stop 1 or 2 times during the
splicing, and press "SET" to continue

Setting
14
In" Setting" interface, " Restorefactory settings" &" Othersettings" areprotected withpasswords.
52%
52%
2021
9
6
14
28
52%
52%

Maintenance
15
52%

Maintenance- ARCCalibration
16
Choose " ARC Calibration" , press " " to enterthe interface.
Put twoprepared barefiber toV-groove,close thecover,then arccalibrate startsautomatically.If prompt
" Please continue" , pleasedo sameoperation asabove untilauto calibrationfinish.
Note: Only doARC calibrationwhen device comesto large changeson discharge power(spliced points withdepressions or bubbles).

Maintenance- Dustcheck
17
Dust checkis tocheck theoptical channelclean ornot, andindicate dustposition.
No needplace fiber, choose " Dustcheck" ,Press" " toenter theinterface, pressagain tostart checking.
If prompts " Dust" ,please cleanobjective lens,light sourcesurface inthe windshieldcover.If stillnot work,
pls contactthe manufacturer.

Maintenance- Electrodes
18
Aging Electrodeis usedfor stabilitytesting ofnew electrode.
Users cancheck" ARCTimes" and" Total ARCTimes" ,and canclearARC Count.
52%
0010