Trinity TLS-7202C User manual

OWNER’S MANUAL
TRINITY 72” x 19” / 72” x 24” Wood Top Work Table
Model # TLS-7202 / TLS-7202C / TLS-7203 / TLS-7203C
Everything in its place.®

Your TRINITY 72” Wood Top Work Table should include the following parts. Please inspect box contents to
ensure you have received all components.
If you are missing any parts, need assistance with assembly or have questions, please contact TRINITY Customer
Service: 800.985.5506 or [e-mail]. Parts can also be requested online at our customer
center at www.trinityii.com.
For assembly you will also need a screwdriver. A drill with 13mm bit and Phillips bit is recommended.
PARTS LIST
WOOD TOP (1)
TLS-7202: 72”x19”
TLS-7203: 72”x24”
A
TOP CROSS BEAM (2)
B
BOTTOM CROSS BEAM (1)
C
LARGE
BOLT (12)
(13mm Hex Head)
D
SMALL
SCREW (20)
(Phillips Head)
E
I
(D) RIGHT SIDE FRAME (1)
(E) LEFT SIDE FRAME (1)
Feet Levelers are pre-installed
JK
LOCKING
CASTER (2)
F
NON-LOCKING
CASTER (2)
G
SMALL
WASHER (20)
WRENCH (1)
LARGE
WASHER (12)
L
(TLS-7202C and TLS-2703C only)
© 2017 TRINITY - 800.985.5506
1
H

ASSEMBLY INSTRUCTIONS
Find the WOOD TOP (A) box inside the package and place it tape-side up
on a flat smooth surface on the ground. Make sure there is enough space
to open and unfold the box.
Open the WOOD TOP (A) box carefully keeping the WOOD TOP (A) laying
face down inside. Unfold the box to use as a work surface.
Place both TOP CROSS BEAMS (B) on WOOD TOP (A). Make sure holes on
the “L” brackets at the end of the beams are on the outside.
STEP 1
B (2)
G
B
E
FB
D
G
G
F
FG
F
G
F
G
F
G
F
G
A
A (1)
Only hand tighten LARGE BOLTS (F). Do
not fully tighten with WRENCH (J) until
after WOOD TOP (A) is fully secured after
Step 4.
© 2017 TRINITY - 800.985.5506 2
F
Take RIGHT (D) and LEFT (E) SIDE FRAMES and orient parts as shown.
For proper installation, please make sure that the holes for the CROSS BEAMS
(B+C) in the RIGHT (D) and LEFT (E) SIDE FRAMES are on the inside.
STEP 2
F (8) G (8)D+E (2)
Hand tighten (2) LARGE BOLTS (F) through (2) LARGE WASHERS (G) and TOP CROSS BEAM (B) onto
RIGHT SIDE FRAME (D). Hand tighten (2) more LARGE BOLTS (F) through (2) more LARGE WASHERS (G)
and TOP CROSS BEAM (B) onto LEFT SIDE FRAME (E).
Repeat these steps to attach the other TOP CROSS BEAM (B) to the other side of SIDE FRAMES (D+E).

C
G
F
G
F
G
F
G
F
ASSEMBLY INSTRUCTIONS
Take BOTTOM CROSS BEAM (C) and align it to SIDE FRAMES (D+E). Hand
tighten LARGE BOLTS (F) through LARGE WASHERS (G) and BOTTOM CROSS
BEAM (C) onto SIDE FRAMES (D+E).
STEP 3
F (4) G (4)
C (1)
© 2017 TRINITY - 800.985.5506
3
Only hand tighten LARGE BOLTS (F). Do
not fully tighten with WRENCH (J) until
after WOOD TOP (A) is fully secured in
Step 4.
Line the frame up with the insert nuts found on the underside of the
WOOD TOP (A).
Insert (20) SMALL SCREWS (H) and SMALL WASHERS (I) and partially
tighten by hand to secure the frame to the WOOD TOP (A).
Once all (20) SMALL SCREWS (H) have been inserted, fully tighten all
SCREWS (H).
STEP 4
H (20) I (20)
I
H
B
A

ASSEMBLY INSTRUCTIONS
HEIGHT OPTION
2
1
3
ADJUST HEIGHT
1. With the Table upside down,
remove LARGE BOLTS (F) and
LARGE WASHERS (G) from Table
legs.
2. Adjust to desired height. Make
sure that this height adjustment
allows for (2) LARGE BOLTS (F) to
be inserted into each Table leg.
Height adjusts from 34” to 40” in
2” increments”.
3. Insert and tighten (2) LARGE
BOLTS (F) and LARGE WASHERS
(G).
4. Adjust Feet Levelers to ensure that
Table is level.
Tighten all LARGE
BOLTS (F) with the
small end of the
WRENCH (J).
Adjust height if desired
(see below) before
carefully turning Table
onto its upright
position.
STEP 5
2
13
J (1)
J (1)
© 2017 TRINITY - 800.985.5506 4

ASSEMBLY INSTRUCTIONS
J
K
MOBILE OPTION
(TLS-7202C AND TLS-7203C ONLY)
1
2
INSTALL CASTERS
1. With the Table upside down, unscrew feet levelers and remove from
Table legs.
2. Screw on CASTERS (K+L) and tighten with the large end of the WRENCH
(J).
LOCKING CASTERS (K) should be installed on the same side.
Use the provided WRENCH (J) to tighten completely. Failure to do as
instructed could result in the caster stem breaking.
J
K
1
2
L (2) J (1)
K (2)
© 2017 TRINITY - 800.985.5506
5

SERVICE PARTS LIST –TLS-7202 / TLS-7202C /
TLS-7203 / TLS-7203C
Part Number Description Part Number Description
1) LNA-06-002-7219 Wood Top-72”x19” 9) ZSV-99-008-4010 Locking Caster
2) LNA-06-002-7224 Wood Top-72”x24” 10) ZBK-01-001-0820 Large Bolt
3) PBK-13-002-6750 Top Cross Beam 11) ZBK-01-007-0816 Large Washer
4) PBK-14-002-1729 Left Side Frame 12) PBK-14-003-1729 Right Side Frame
5) PBR-04-011-1250 Leg 13) PBK-13-001-6750 Bottom Cross Beam
6) XWH-98-001-4264 Feet Leveler 14) ZSV-01-004-0415 Small Screw
7) ZSV-99-007-4010 Non-locking Caster 15) ZSV-01-007-0412 Small Washer
8) XXX-97-002-0001 Wrench
TRINITY Customer Service provides the following replacement parts:
15
14
12
11
10
9
13
5
2
6
3
8
7
1
4
© 2017 TRINITY - 800.985.5506 6

WARNINGS
1. Read and understand all instructions. Failure to follow all instructions may result in injury
and/or damage.
2. (Mobile Option) Use the provided caster wrench to tighten casters completely. Failure to
do as instructed could result in the caster stem breaking thereby causing the shelving rack
to collapse.
3. The warnings, cautions, and instructions discussed in this manual cannot cover all
possible conditions or situations that may occur. The user must always be aware of their
environment and ensure that they use the product in a safe and responsible manner.
4. Do NOT modify the product in any way. Unauthorized modification may impair the
function and/or safety of the product, and may affect the life of the product.
5. Check for damaged parts.Before using this product, carefully check that all parts are in
good condition, and that the product will operate properly and perform its intended
function. Check for damaged parts and any other conditions that may affect the operation
of this product. Replace damaged or worn parts, and never use this product with a damaged
part.
6. Do NOT overload the product.
7. Assemble the product as instructed. Ensure that ALL screws are used to assemble the
product. Do NOT leave any off.
CARE AND MAINTENANCE
•Avoid harsh, abrasive cleaners, and other corrosive chemicals.
•Wood top can be cleaned with damp cloth and wiped dry immediately with dry cloth. If
needed, solvent-based wood furniture cleaner can be used.
•Clean up any spills immediately to prevent stains from forming on the wood top.
Weight capacity on feet levelers 2,000 lb
Weight capacity on casters 600 lb
© 2017 TRINITY - 800.985.5506
7

Thank you for purchasing a TRINITY 72” Wood Top Work Table. In order to register your product and
receive streamlined customer service, please fill out the following Product Registration Form and (1)
fax the form to 310.347.4134 (2) complete the Product Registration Form online at www.trinityii.com
or (3) scan and email the form to [e-mail]. Include a copy of your original receipt
with your submission.
First Name: Last Name:
Address:
City: State: Zip Code:
Email Address: Phone:
Product Model #: Purchase Date: / /
Location of Purchase:
Please rate the importance of each feature (1=least important; 10=most important)
Quality Price Size/Capacity Appearance Other
How did you hear about our product?
Magazine Ad Catalog Salesperson Word of Mouth
Internet Store Display Other
Marital Status: Single Married
Household Income: Below $50,000 $50,000-$150,000 $150,000+
Education: High School College Graduate School
Primary Residence: Own Rent
Comments/Suggestions:
PRODUCT REGISTRATION
© 2017 TRINITY - 800.985.5506 8

© 2017 TRINITY - 800.985.5506
9