Trinity TLSPBK-0605 User manual

OWNER’S MANUAL
TRINITY 36” Garage Modular Cabinet
Model # TLSPBK-0605
Important / Important / Importante
FOR QUICK & EASY 3D ASSEMBLY INSTRUCTIONS
POUR DES DIRECTIVES D’ASSEMBLAGE 3D RAPIDES ET FACILES
PARA INSTRUCCIONES DE ENSAMBLAJE RÁPIDAS Y SENCILLAS EN 3D
Intelligent Instructions
Directives intelligentes
Instrucciones Inteligentes
DOWNLOAD THE FREEAPP | TÉLÉCHARGERL’APPLICATION GRATUITE| DESCARGUE LA APLICACIÓN GRATUITA

PARTS LIST
Your TRINITY 36” Garage Modular Cabinet should include the following parts. Please inspect box
contents to ensure you have received all components.
If you are missing any parts, need assistance with assembly or have questions, please contact TRINITY
Customer Service: 800.985.5506 or [e-mail]. Parts can also be requested online
via “Contact Us” section at www.trinityii.com.
You will need a Phillips screwdriver for assembly which is not provided.
A
CABINET BODY (1)
B
TOP PANEL (1)
C
BOTTOM PANEL (1)
D
LEFT DOOR (1)
E
RIGHT DOOR (1)
F
LEFT DOOR HINGE (1)
G
RIGHT DOOR HINGE (1)
H
SHELF (1)
I
SHELF SUPPORT (4)
J
FEET LEVELER (4)
K
KEY (2)
L
BLACK SCREW
(32) + (2) extra
M
MOUNTING SCREW (4)
N
ANCHOR (4)
O
CONNECTING SCREW (4)
1© 2020 TRINITY - 800.985.5506

ASSEMBLY INSTRUCTIONS
STEP 1
Unfold CABINET BODY (A).
STEP 2
Two people are recommended for ease of assembly.
Stand unfolded CABINET BODY (A) upside down on
floor.
Note: There is a 40mm diameter hole on back panel of
CABINET BODY (A). When CABINET BODY (A) is upside
down, this hole should be in the upper left corner of the
back panel.
Turn BOTTOM PANEL (C) upside down. Tilt the front
diagonally downward. First, insert the lip into inner side
of tab of CABINET BODY (A) at the right side, then insert
into the left side.
Follow the order indicated, insert (12) BLACK SCREWS
(L) through holes on BOTTOM PANEL (C) and tighten
fully with a Phillips screwdriver. Insert (4) BLACK
SCREWS (L) through tabs on front of CABINET BODY (A)
and tighten fully to BOTTOM PANEL (C).
1
hole
12
3
3
C
A
4
tab
lip
L
© 2020 TRINITY - 800.985.5506 2

ASSEMBLY INSTRUCTIONS
STEP 3
Screw FEET LEVELERS (J) into each pre-
installed nut in four corners of BOTTOM
PANEL (C).
J
C
STEP 4
Stand the unit right side up.
Tilt front of TOP PANEL (B) diagonally downward. First,
insert the lip into inner side of tab of CABINET BODY (A) at
the right side, then insert into the left side.
Follow the order indicated, insert (8) BLACK SCREWS (L)
through holes on TOP PANEL (B) and tighten fully with a
Phillips screwdriver. Insert (4) BLACK SCREWS (L) through
tabs on front of CABINET BODY (A) and tighten fully to TOP
PANEL (B). tab
lip
B
L
3
2
1
1
A
3© 2020 TRINITY - 800.985.5506

ASSEMBLY INSTRUCTIONS
STEP 5
Note: RIGHT DOOR (E) has a lock on it.
Attach LEFT DOOR (D) to cabinet by sliding LEFT
DOOR (D) onto pivot of door hinge which is welded
to BOTTOM PANEL (C)
Position LEFT DOOR HINGE (F) at left front corner
of TOP PANEL (B). Make sure to insert pivot of
DOOR HINGE (F) fully into cylinder on LEFT DOOR
(D). Align holes on DOOR HINGE (F) to pre-installed
nuts on TOP PANEL (B). Insert BLACK SCREWS (L)
through these holes. Tighten fully with a Phillips
screwdriver.
Repeat for RIGHT DOOR (E).
Adjust FEET LEVELER (J) as needed to ensure your
cabinet is level and stable.
FG
B
E
C
L
J
D
cylinder
pivot
STEP 6
Attach SHELF SUPPORT (I) by hooking it over
position tab at desired height. Make sure all
four SHELF SUPPORTS (I) are at the same
level.
Tilt SHELF (H) diagonally to move it inside
cabinet. Place SHELF (H) on top of all four
SHELF SUPPORTS (I).
I
Shelf supports hooked
on position tabs
H
position tab
© 2020 TRINITY - 800.985.5506 4