tropitone 840838SWB User manual

1
Travertine Tables & KD Scroll Bases
Base Assembly and Top Attachment
840838SWB
840848SWB
840867SWB
840886SWB
840896SWB
840898SWB
TV27S TV5034 TV55RU TV9648OU
Congratulations on the purchase of your Tropitone furniture.
Read through all steps before starting assembly.
CAUTION: Do not try to lift or flip components with only
one person. Components may be heavy and awkward to
handle, and may result in injury to persons or damage to
property if not lifted properly.
Tools Required
5/16” Wrench
7/16” Wrench
1/2” Wrench
Permanent Marker
1/8” Drill Bit (with masking tape
at 3/4” depth)
Power Drill
Safety Glasses
End Table (22” Ht.) Parts List
(4) Table Legs
(1) Leg Brace
(1) 27” Square Table Top
Coffee Table (18” Ht.) Parts List
(4) Table Legs
(1) Leg Brace
(1) Upper Brace
(1) 50”x34” Table Top
Dining (28” Ht.), Bar (39” Ht.) and Chat (24” Ht.) Table Parts List
(4) Table Legs
(1) Leg Brace
(1) Top Ring
(1) Table Top: 55” Round or 96”x48” Oval
(2) Support Arms (96”x48” dining only)
Base hardware is screwed into place in the legs.
Table top hardware is included in a bag with the top.
Use the shipping carton, pool towels or a tarp to prepare a
smooth, non-scratch work surface.
Assembled tables are
ver
y
heav
y
. Put to
g
ether
at place of use.
2
Dining, Bar and Chat Tables
Don’t fully tighten the bolts until Top Attachment Step 4.
Step 1
Place the Top Ring on the prepared work surface. The oval table
ring must be upside down so the top attachment tabs face down
(see picture in Step 3). Attach the Table Legs with bolts and split
washers; hand tighten only (4 places).
Step 2
Invert the Leg Brace so that it will arch towards the bottom of the
table top (arching upwards when upright). Attach the Leg Brace
to the Table Legs with bolts and split washers; hand tighten only
(4 places).

3
Step 3 96”x48” Oval Dining Only
Attach the Support Arms to the Top Ring and to the Leg Brace
with bolts and split washers; hand tighten only (4 places).
Go to Top Attachment section.
Tabs are down
4
End Table (Base is assembled upright)
Don’t fully tighten the bolts until Top Attachment Step 4.
Step 1
On the prepared work surface, place the Leg Brace onto the
mount on one Table Leg with the Leg Brace is arching upwards.
Install the bolts with split washers; hand tighten only.
Repeat for the remaining three legs; hand tighten only.
Go to Top Attachment section.

5
Coffee Table
Don’t fully tighten the bolts until Top Attachment Step 4.
Step 1
Place the Upper Brace upside down on the prepared work
surface. Attach the Table Legs with bolts and split washers; hand
tighten only (4 places).
Step 2
Invert the Leg Brace so that it will arch towards the bottom of the
table top (arching upwards when upright). Attach the Leg Brace
to the Table Legs with bolts and split washers; hand tighten only
(4 places).
Go to Top Attachment section.
6
Top Attachment
Step 1
Assembled tables are very heavy.
Put together at place of use.
Using two or more persons, place Table
Top upside down on the prepared work
surface. Observe the circle marks that
indicate internal mounting pads to
capture the screws (4 or 8 places).
Step 2
Using two or more persons, place assembled Table Base upside
down on the Table Top. Align the base mounting holes to the
mounting pad marks. Insure the base is centered on the top.
For tops with an umbrella hole, carefully align the base umbrella
support ring to the top umbrella hole.
For rectangular, oval and square tables, insure the base is
aligned straight to the table top edges.
Step 3
Use a permanent marker to mark on the top to indicate the screw
mount locations (4 or 8 places). Using two or more persons,
remove the Table Base and place on the prepared work surface.
Drill 1/8” pilot holes 3/4” deep into the table top at each of the
marked screw mount locations (4 or 8 places). Using two or more
persons, replace the Table Base onto the Table Top (confirm the
alignment in Step 2 above).
Screw the base to the top (4 or 8 places) using the #12 screws.
Fully tighten all the screws using the 5/16” wrench.
(4) 1” screws:
55” Round Top (4) 1” screws: 96”x48” Oval Top

7
Step 4A Dining Tables
Using the 1/2” wrench, fully tighten the
Table Legs to the Top Ring (4 places).
Using the 1/2” wrench, fully tighten the
Table Legs to the Leg Brace (4 places).
Using the 1/2” wrench, fully tighten the
bolts connecting the Support Arms to the
Top Ring and to the Leg Brace (4 places).
Step 4B End Table
Using the 1/2” wrench, fully tighten the
bolts connecting the Table Legs to the Leg
Brace (4 places).
Step 4C Coffee Table
Using the 7/16” wrench, fully tighten the
Table Legs to the Upper Brace (4 places).
Using the 1/2” wrench, fully tighten the Leg
Brace to the Table Legs (4 places).
Step 5
Caution: Lift with your legs, not your back! Your table is now
fully assembled and ready for two or more persons to lift into an
upright position. While on the prepared work surface, lift the table
by lifting the top (not the legs) until the top is vertical. Hold both
the top and base and lift the table into an upright position. Move
the table into final position by lifting the base (not the top).
(8) 1-1/2” screws:
50”x34” Rect. Top
(8) 1-1/2” screws:
27” S
q
uare To
p
8
MORE INFORMATION
See Natural Stone Cleaning and Natural Stone Sealing in the
Safety, Care, Maintenance and Warranty Information guide
included with your furniture and available at www.tropitone.com –
click on Product Care.
Additional care information, “How To” videos (including Table
Assembly), pictures of glides and end caps, and assembly
instructions for Tropitone Outdoor Furniture and Basta Sole
Umbrellas are also available at our website.
If you have difficulty understanding any of the instructions and
need assistance while assembling your furniture together, please
call Tropitone’s Customer Service Center at 949-951-2010.
Tropitone Furniture Co., Inc.
5 Marconi, Irvine, CA 92618
949 951 2010 phone
www.tropitone.com
Part # R9T00003
Revised: 041309
©2009 Tropitone Furniture Co., Inc.