tropitone Cabana Club User manual

For additional Cabana Club assembly and product care
instructions, see www.tropitone.com and select Product Care.


Cabana Club Cleaning and Care


Cabana Club Component Assembly Instructions


Cabana Club Party Lounger and Natural Stone Drink Table
Assembly Instructions
If you have difficulty understanding any of the instructions and
need assistance while fastening your components together,
please call Tropitone’s Customer Service Center at 949-951-2010.
Tropitone Furniture Co., Inc.
5 Marconi, Irvine, CA 92618
949 951 2010 phone
www.tropitone.com
Part # R9T00014
Revised: 21314
©2014 Tropitone Furniture Co., Inc.
Cabana Club Fabric & Woven Panel
Assembly Instructions
Congratulations on the purchase of your Tropitone Cabana Club
modular seating with Panels. Read through all steps before
attaching panels.
CAUTION: Do not try to lift or flip components with only
one person. Components may be heavy and awkward to
handle, and may result in injury to persons or damage to
property if not lifted properly.
Tools Required
5/32” Hex Key (Allen Wrench) Safety Glasses
Half Panel Parts Lists
5xxxHPFS (Flat Straight)
(4) Lower Brackets
(4) ¼” x ½” Button Head Screws
(4) ¼ Lock Washers
(4) ¼” x ¾” Button Head Screws
Fabric Panels will use 6 of each
5xxxHPFC (Flat Curved)
(8) Lower Brackets
(8) ¼” x ½” Button Head Screws
(Use with Woven Panels)
(8) ¼” x ¾” Button Head Screws
(Use with Fabric Panels)
(8) ¼ Lock Washers
Full Panel Parts Lists
5xxxFPFS (Flat Straight)
5xxxFPLS (Fabric Only)
5xxxFPRS (Radius Straight)
(2) Lower Brackets
(2) Upper Brackets
(4) ¼” x ¾” Button Head Screws
(4) ¼ Lock Washers
5xxxFPFC (Flat Curved)
5xxxFPFP (Party Lounger)
(4) Lower Brackets
(4) Upper Brackets
(12) ¼” x ¾” Button Head Screws
(12) ¼ Lock Washers
Lower
Upper
Bracket

Configuration
5xxx11AC
Arm Chair
5xxx10SC Square
Corner
5xxx10MC Center
Module
5xxx10CC Curved
Corner
5xxx17SO
Square Ottoman
5xxx08CO Curved
Ottoman
5xxx50
Party Lounger Quarter Section with Backrest
Panel Configurations
Cabana Club Modules
FPRS
FPLS FPFS HPFS FPFC HPFC
5xxx11AC Arm Chair 2 1 1 - -
5xxx11AC Arm Chair - - 4 - -
5xxx10SC Square Corner 1 1 2 - -
5xxx10SC Square Corner - 2 2 - -
5xxx10SC Square Corner - - 4 - -
5xxx10MC Center Module - 1 3 - -
5xxx10MC Center Module - - 4 - -
5xxx17SO Square Ottoman - - 4 - -
5xxx10CC Curved Corner - - 2 1 -
5xxx10CC Curved Corner - - 2 - 1
5xxx08CO Curved Ottoman - - 2 - 1


The item quantities in each row indicate the maximum
panel configuration.


The total number of panels required varies depending
upon your modular configuration.
Step 2
With modules in an upright position, assemble panel by sliding the
tightened lower brackets until they capture the frame.
Step 3
Rotate the upper (loose) brackets, install the lock washers and
screws, and then fully tighten all the screws. Repeat for all panels.
Brackets can be adjusted by loosening screws and moving up or
down as necessary.

Full Panel Assembly
Step 1
Prepare a smooth, non-scratch surface (a tarp or pool towels can
be placed on your work surface). Place the woven panels on
prepared work surface and determine the panel top and bottom by
measurement. The bottom of the Party Lounger panel has glides
that contact the ground.
Connect lower brackets with lock washers and screws. Fully
tighten the bottom brackets. Connect the upper brackets. Don’t
fully tighten the upper brackets at this time.
Connect brackets in 4 places.
Fully tighten 2 bottom brackets.
Connect brackets in 8 places.
Fully tighten 4 bottom brackets.
Upper Bracket
s
Lower Bracket
s
1.5”
2”
Panel Types
Full Panels (FPxx) cover the full height of the module.
Half Panels (HPxx) cover the lower third of the module.
FPRS/FPLS
36” Radius/Flat Profile
Straight
FPFS HPFS
34” Flat Profile
Straight
FPFC HPFC
Flat Profile Curved
Radius Profile and Flat Profile panels are designed to fit together
as a set.
Radius panels overhang the end
of the module to form a butt joint
with the Flat panel making a
finished seam.
*FPLS fits the same but flat.
Two adjacent Flat panels leaves
the corner open.

Half Panel Assembly
Half panels should be connected to Cabana Club modules before
modules are assembled together.
Step 1
Prepare a smooth, non-scratch surface (a tarp or pool towels can
be placed on your work surface). Place the woven panels on
prepared work surface.
Connect brackets with lock washers and screws. Fully tighten the
bottom brackets. Don’t fully tighten the top brackets at this
time.
Step 2
Frame modules can be placed upside down or on the side on the
prepared work surface. Assemble panel by sliding until the
tightened lower brackets capture the frame.
Connect brackets in 4 or 6 places.
Fully tighten 2 or 3 bottom brackets.
Connect brackets in 8 places.
Fully tighten 4 bottom brackets.
Shown upside down.
Bottom brackets have captured the frame.
Step 3
Rotate the top (loose) brackets until
they capture the frame and fully
tighten the screws. See pictures for
Stainless Steel and Aluminum
Frame orientation for brackets.
Repeat for all panels. Brackets can
be adjusted by loosening screws
and moving up or down as
necessary.
Step 4
Turn furniture into an upright position. You can assemble
components together if required (see separate Cabana Club
Assembly instructions). Continue on to Full Panel Assembly if
needed.
Stainless Steel
Frame Connection
Aluminum Frame
Connection