tropitone Party Lounger User manual

8
MORE INFORMATION
For care and cleaning instructions, refer to the Tropitone® Care,
Maintenance, Safety & Warranty Information guide included with
your furniture and available at www.tropitone.com/warranty.
Additional care information, “How To” videos and assembly
instructions for Tropitone®Outdoor Furniture and Basta Sole®
shade products are also available at our website.
If you have difficulty understanding any of the instructions and
need assistance while assembling your Cabana Club Aluminum
Square Party Lounger, please call Tropitone’s Customer Service
Center at 949-951-2010.
Tropitone Furniture Co., Inc.
5 Marconi, Irvine, CA 92618
949 951 2010 phone
www.tropitone.com
Part # R9T0907
Revised: 03.18.2013
©2013 Tropitone Furniture Co., Inc.
1
Cabana Club Aluminum Square
Party Lounger
Assembly Instructions
Congratulations on the purchase of your Tropitone®Cabana Club
Party Lounger. Read through all steps before fastening
components together.
WARNING: Do not try to lift or flip components with only one
person. Components may be heavy and awkward to handle, and
may result in injury to persons or damage to property if not lifted
properly.
CAUTION: When instructed to fully tighten screws, do not over
tighten and strip the threads.
Read through all steps before starting assembly.
Completely unpack all boxes and thoroughly check
for items that may be individually wrapped.
 Check that all items listed in the Parts List are in
your cartons.
Tools Required
7/16” Wrench Safety Glasses
8’ x 8’ Party Lounger Parts List
(2) 4’ x 8’ Party Lounger
Sectional Frames
(8) Connector Plates
(16) ¼” Locking Washers
(16) ¼-20 x 7/8” Hex Head Bolts
(1) 8’ Square Party Lounger
Cushion
(1) 8’ Headrest Cushion
(Optional)
(16) ¼” Flat Washers
4’ x 8’ Party Lounger Parts List
(1) 4’ x 8’ Party Lounger
Sectional Frame
(1) 4’ x 8’ Party Lounger Cushion
(1) 4’ Headrest Cushion
(Optional)
Assembled furniture
is heavy. Assemble
at place of use.

2
8’ x 8’ Square Party Lounger
Step 1 Connector Plate Attachment – 8’ x 8’ Party Lounger
Align (1) 4’ x 8’ Party Lounger Sectional Frame to be assembled
at or near the desired location of your completed 8’ Square Party
Lounger.
Install (4) Connector Plates to the assembly holes in the lower
side bracing of the Sectional using (4) ¼-20 x 7/8” Hex Head Bolts
fitted with (4) ¼” Locking Washers and (4) ¼” Flat Washers. Hand
tighten Hex Head Bolts with the Connector Plates positioned to
accept the second 4’ x 8” Party Lounger Sectional.
Note: Do not tighten the Hex Head Bolts until instructed to do so
in Step 2.
Install the remaining (4) Connector Plates to the assembly holes in
the upper side bracing of the Sectional using (4) ¼-20 x 7/8” Hex
Head Bolts fitted with (4) ¼” Locking Washers and (4) ¼” Flat
Washers. Hand tighten Hex Head Bolts with the Connector Plates
positioned to accept the second 4’ x 8” Party Lounger Sectional
Frame.
Install Upper Connector Plates
Install Lower Connector Plates
7
Step 3 Headrest Cushion Attachment (Optional) 4’ x 8’
Align your Headrest Cushion (Optional) at the desired end of your
4’ x 8’ Party Lounger on top of the Cushion. Wrap the Velcro
Straps around the side Cushion and underneath the Seating Grid
of the 4’ x 8’ Party Lounger Frame, both sides. See below
illustration.
Engage the Velcro Straps at the center and underside of the
Seating Grid of your 4’ x 8’ Party Lounger.
Headrest Cushion (Optional)
4’ x 8’ Party Lounger with (Optional) Headrest Cushion

6
4’ x 8’ Rectangular Party Lounger
Step 1 Assembly of 4’ x 8’ Party Lounger
Place (1) 4’ x 8’ Party Lounger Sectional Frame to be assembled
at or near the desired location for use.
Step 2 Cushion Attachment – 4’ x 8’ Party Lounger
WARNING: Do not try to lift or move the Seat Cushion with only
one person. This component is heavy and awkward to handle, and
may result in injury to persons or damage to property if not lifted
properly.
Place Seat Cushion with Velcro Straps facing down onto your 4’ x
8’ Party Lounger Frame.
Engage Velcro Straps (12) to Frame Seating Grid Bracing, located
around the perimeter of your Square Party Lounger.
3
Step 2 Sectional Attachment – 8’ x 8’ Party Lounger
Align the second 4’ x 8’ Party Lounger Sectional Frame to be
attached to the first Sectional with the Connector Plates installed.
WARNING: The attachment of your (2) 4’ x 8’ Party Lounger
Sectional Frames requires assembly in the center of the item. Do
not step or climb on the frame of your Party Lounger Sectionals.
Use a supporting platform, such as cardboard over the seating
grid when performing the below step. Failure to do so could result
in injury to persons or damage to property.
Align both upper and lower Connector Brackets with the assembly
holes in upper and lower side bracing of the second 4’ x 8’ Party
Lounger Sectional Frame.
Install the remaining (8) ¼-20 x 7/8” Hex Head Bolts fitted with (8)
¼” Locking Washers and (8) ¼” Flat Washers through the
Connector Brackets into the assembly holes. Be sure that the
Sectionals are properly aligned at the end of the joined items.
Fully tighten all (16) Hex Head Bolts.
DO NOT STEP OR CLIMB ON SEATING GRID WITHOUT THE
USE OF A SUPPORTING PLATFORM MATERIAL SUCH AS
CARDBOARD!
Side of Party Lounger Frame
Ends of Party
Lounger Frames

4
Step 3 Cushion Attachment – 8’ x 8’ Party Lounger
WARNING: Do not try to lift or move the Seat Cushion with only
one person. This component is heavy and awkward to handle, and
may result in injury to persons or damage to property if not lifted
properly.
Place Seat Cushion with Velcro Straps facing down onto your
assembled 8’ Square Party Lounger Frame. Be sure that the side
of the cushion (5 straps) is aligned with the side of the Sectional
Frame. See below illustration.
Engage Velcro Straps (18) to Frame Seating Grid Bracing, located
around the perimeter of your Square Party Lounger.
Cushion End
Velcro Straps
Cushion Side
Velcro Straps
5
Step 4 Headrest Cushion Attachment (Optional) – 8’ x 8’
Align your Headrest Cushion (Optional) at the desired end of your
Square Party Lounger on top of the Cushion. Wrap the Velcro
Straps around the side Cushion and underneath the Seating Grid
of the Square Party Lounger Frame, both sides. See below
illustration.
Engage the Velcro Straps at the center and underside of the
Seating Grid of your Square Party Lounger.
Headrest Cushion (Optional)
8’ x 8’ Party Lounger with (Optional) Headrest Cushion