tropitone Evo 360936B User manual

Evo Pedestal Table Top Attachment
360936B Dining Base 360997B Bar Height Base
Thank you for selecting Tropitone furniture.


Read through all steps before starting assembly.


Locate all items in the Parts List from your cartons.
WARNING! Do not try to lift or flip furniture components
with only one person. Components may be heavy and
awkward to handle, and may result in injury to persons or
damage to property if not lifted properly.
WARNING! Do not sit on or put your full weight on the
edge of the table. Serious injury could result.
CAUTION: Proper screw length should allow ½” – ¾” of
threads to penetrate into the Top surface. Confirm proper
screw length before starting Top attachment. See Step 1.
Tools Required
5/16” Socket Driver or
Flathead Screwdriver
1/4” Hex Key (Allen Wrench)
Tape Measure
Permanent Marker (Felt Tip)
Safety Glasses
Parts List
(1) Spider Support
(1) Column: Dining Height or Bar
Height
(1) Base Plate
(1) Thumbscrew
(8) 5/16” x 1-1/4” Socket Head Cap
Screws
(8) #10 x 1-1/4” Self-Tapping Screws
Assembled tables are
large & heavy. Put
together at place of use.
Step 1
CAUTION: It is the assembler’s and user’s
responsibility to confirm and install proper
length screws to prevent damage to the Top.
Place one screw into the Spider Support mount.
Measure the length of the screw threads to
insure they stick up ½” – ¾”.
x If the screw sticks up more than ¾”, do NOT proceed.
The screws are too long and will stick up through the
Top surface.
x If the screw sticks up less than ½”, do NOT proceed.
The screws are too short and will not properly secure
the Top.
Step 2
Prepare a smooth, non-scratch work
surface (shipping container, a tarp or
pool towels can be used).
With two persons, place the Table
Top upside down on the prepared
work surface. Turn the Spider
Support upside down and place onto
the center of the Top.
Square tops Be sure that the Spider
Support arms point toward the corners of
the top.
•Top with umbrella hole Sight down through the umbrella
support ring and align to the hole on the Top.
•Top without umbrella hole Measure equal distances from
the edge at four (4) places to center the Spider Support on the
Top.
Using the permanent marker, make a small, discrete mark on the
Base and the Top at two or more mounting points to indicate the
alignment.
Lift the Spider Support off the Top. Do NOT attach the Spider
Support to the Top until Step 4.
SCREW LOCATIONS (8 PLACES)

Step 3
Identify the top of the Column by
locating the hole for the umbrella
thumb screw; orient this up towards
the Spider Support.
With two persons, hold the Column
vertical and place the Spider
Support onto the Column.
Install (4) Socket Head Cap Screws
in the
Spider Support into the
counterbore holes. Fully tighten the
screws with the ¼” Hex Key.
Step 4
Turn the Column assembly upside down onto the table Top; align
the Spider Support to the marks made in Step 2. Attach the Base
to the Top using eight (8) #10 self tapping screws.
NOTE: After assembling one table top, proceed to Step 5 to
complete Table assembly and then turn upright. Confirm the
screws have not penetrated up through the top surface.
Step 5
Position the Base Plate with the Glides
up. With two persons, lift and hold the
Base Plate onto the Column and align
to the threaded holes. Install (4)
Socket Head Cap Screws into the
counterbore holes. Fully tighten the
screws with the ¼” Hex Key.
With two persons, lift up by the Base
and Column to turn the table sideways
then place the Base on the ground
without lifting by the Top. Finish by
lifting the Spider Support to tilt the
table upright.
Install the umbrella (optional).
Install the umbrella Thumbscrew into the Column; fully tighten.
GLIDES
MORE INFORMATION
For care and cleaning instructions, refer to the Tropitone Care,
Maintenance, Safety & Warranty Information guide included with
your furniture and available at www.tropitone.com – click on
Product Care.
Additional care information, “How To” videos and assembly
instructions for Tropitone Outdoor Furniture and Basta Sole shade
products are also available at our website including:
Evo Woven Modular Furniture Assembly
Stoneworks Tops Touch Up
Frame Finish Touch Up
If you have difficulty understanding any of the instructions and
need assistance, please call Tropitone’s Customer Service Center
at 949-951-2010.
Tropitone Furniture Co., Inc.
5 Marconi, Irvine, CA 92618
949 951 2010 phone
www.tropitone.com
Part # R9T00018
Revised: 11-11-19
©2010 Tropitone Furniture Co., Inc.