tropitone Stoneworks User manual

MORE INFORMATION
For care and cleaning instructions, refer to the Tropitone Care,
Maintenance, Safety & Warranty Information guide included with
your furniture and available at www.tropitone.com – click on
Product Care.
Additional care information, “How To” videos and assembly
instructions for Tropitone Outdoor Furniture and Basta Sole shade
products are also available at our website including:
Stoneworks Tops Touch Up
Frame Finish Touch Up
If you have difficulty understanding any of the instructions and
need assistance, please call Tropitone’s Customer Service Center
at 949-951-2010.
Tropitone Furniture Co., Inc.
5 Marconi, Irvine, CA 92618
949 951 2010 phone
www.tropitone.com
Part # R9T00108
Revised: 04-08-13
©2010 Tropitone Furniture Co., Inc.
Stoneworks
®
Top Attachment
Flat Underside
Thank you for selecting Tropitone furniture.
Read through all steps before assembling tables together.
Locate all items in the Parts List from your cartons.
WARNING: Do not try to lift or flip furniture with only one
person. Furniture pieces may be heavy and awkward to
handle, and may result in injury to persons or damage to
property if not lifted properly.
WARNING: Do not sit on or put your full weight onto the
table. Serious injury could result.
CAUTION: Proper screw length should allow ½” – ¾” of
threads to penetrate into the Top surface. Confirm proper
screw length before starting Top attachment. See Step 1.
Parts List
Table Top
Table Base
(4) or (6) #10 Screws, self-
tapping, length is 7/8” to
1-3/4” for various bases
Tools Required
5/16” Socket Driver or
Flathead Screwdriver
Permanent Marker (Felt Tip)
Tape Measure
Safety Glasses
Assembled tables are
large & heavy. Put
together at place of use.

Step 1
CAUTION: It is the assembler’s and user’s
responsibility to confirm and install proper
length screws to prevent damage to the Top.
Place one screw into the Table Base. Measure
the length of the screw threads to insure they
stick up ½” – ¾”.
x If the screw sticks up more than ¾”, do NOT proceed.
The screws are too long and will stick up through the
Top surface.
x If the screw sticks up less than ½”, do NOT proceed.
The screws are too short and will not properly secure
the Top.
Step 2
Prepare a smooth, non-scratch work surface (shipping container,
a tarp or pool towels can be used). With two persons, place the
Table Top upside down on the prepared work surface. With two
persons, gently place the Base upside down onto the Top.
Step 3
Tops with Umbrella Hole
Center the Base on the underside of the Top; sight down through
the umbrella support ring in the Base and align it to the Top.
 Square, Rectangular Tops: Align the Base to the corners
of the Top.
 Round Tops: Continue to step 4.
 Oval Tops: Align the Base to the edges of the Top.
Tops without Umbrella Hole
Center the Base on the underside of the Top.
 Square, Rectangular Tops: Align the Base to the corners
of the Top. Measure equal distances at (4) places from the
corner of the Top to the leg mount.
 Round, Oval Tops: Measure equal distances at (4) places
from the edge of the Top to the leg mount.
Proper Base to Top orientation
Square Rectangular Round Oval
Step 4
Attach the Base to the Top using the supplied screws at (4) or (6)
places.
NOTE: After assembling one Table, turn the Table upright.
Confirm the screws have not penetrated up through the top
surface.
With two persons, lift the table upright while holding the Base near
the (4) outermost Base to Top connection points.
Check that all the screws are firmly tightened at (4) or (6) places
to retain the Top.