Trox Technik FKRS-EU User manual

Fire damper
Type FKRS-EU
Supplementary installation manual
Read the instructions prior to performing any task!
Installation kit GL for flexible ceiling joint
GB/en

A00000072713, 1, GB/en
Translation of the original
© 2019
TROX GmbH
Heinrich-Trox-Platz
47504 Neukirchen-Vluyn, Germany
Germany
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
Internet: http://www.troxtechnik.com
01/2019
Fire damper Type FKRS-EU2

1 Installation kit GL
1.1 Supply package
Fig. 1: Supply package FKRS-EU with installation kit GL
1 FKRS-EU with installation kit GL
2 Bracket
A Installation side
B Operating side
Installation kit-Dimensions
Nominal size 100 125 150 160 180 200 224 250 280 315
ÆDN 99 124 149 159 179 199 223 249 279 314
☐ANominal size + 100 mm
Supply package
Item Name Quantity
1FKRS-EU with installation kit GL 1
2Bracket 4
The GL installation kit is pre-assembled on the fire damper.
Installation kit GL
Supply package
Fire damper Type FKRS-EU 3

1.2 Requirements
To be provided by others
Item Name Property - Size
3Fire-rated plasterboard d = 12,5 mm
4Fire-rated plasterboard d = 20 mm 3
5UW section 50 × 40 × 0,6 mm / 50 × 60 × 0,6 mm 1,2
6CW section 50 × 50 × 0,6 mm 2
7Chipboard screw Æ5 × 100 mm 4, 5
8Chipboard screw Æ4 × 60 mm 5
9Chipboard screw Æ4 × 35 mm 5
10 Chipboard screw Æ4 × 12 mm 5
11 HUS anchor bolt Æ6 × 60 mm 5
12 Mineral wool depending on wall construction
13 Filler (to compensate for unevenness) Typ LaFillfresh or equivalent
14 Dry wall screw TN Æ3,9 × 35 mm
15 Dry wall screw TN Æ3,9 × 20 mm
16 Mineral wool 10 mm thick, melting point ≥ 1000 °C
17 Hammer-in fixing
18 Filler (between the kits) Typ LaFillfresh or equivalent
19 Holding plate on both sides Sheet steel, ≥ 1 mm thick, approx. 90 × 120 mm
Positions 3 to 19 are components to be provided by others.
1 min. leg length ≥ a + 20 mm
UW profile 50 × 40 × 0,6 mm for subsidence of the ceiling
slab a = 0 – 20 mm
UW profile 50 × 60 × 0,6 mm for subsidence of the ceiling
slab a = 0 – 40 mm
2 Profile width depending on wall construction
3 3 strips at a ≤ 40 mm, 2 strips at a ≤ 20 mm
4 Æ5 × 80 mm when using 2 strips (Pos. 4)
5 Pre-drill 5 screw holes
Fig. 2: Requirements
W Wall thickness, 100 – 235 mm
B Cladding
W-2B Width of the support structure
a Subsidence of the ceiling slab, 0 – 40 mm
Installation kit GL
Requirements
Fire damper Type FKRS-EU4

2 Installation options
Fig. 3: Separate installation of the FKRS-EU with installation kit
Fig. 4: ≥ 100 mm distance between two installation kits
Fig. 5: Distance between two installation kits 2 - 5 mm to each other
DA Distance installation kit to the ceiling, 0 – 180 mm
* optional
Distance of the FKRS-EU to adjacent walls constructive ≥ 125 mm.
Installation options
Fire damper Type FKRS-EU 5

3 Installation
3.1 DA = 0 mm
Fig. 6: Installation – DA = 0 mm
1pre-drill with 4 mm (Pos. 7), with 3 mm (Pos. 8)
Fig. 7: Installation – DA = 0 mm
1pre-drill with 4 mm (Pos. 7), with 3 mm (Pos. 8)
2drawn W = 175 mm
Installation
DA = 0 mm
Fire damper Type FKRS-EU6

Fig. 8: Installation – DA = 0 mm
1pre-drill with 4 mm (Pos. 7), with 3 mm (Pos. 8)
3drawn W = 200 mm
Fig. 9: Fixing the brackets to the installation kit GL
1pre-drill with 3 mm
Installation
DA = 0 mm
Fire damper Type FKRS-EU 7

Fig. 10: Fixing the fire-rated plasterboard to the installation kit GL
1drawn W = 175 mm
2drawn W = 200 mm
Installation
DA = 0 mm
Fire damper Type FKRS-EU8

Fig. 11: Create an appropriate opening with DA = 0 mm
* at a = 40 mm (drawn)
** closed side for installation opening
Installation
DA = 0 mm
Fire damper Type FKRS-EU 9

Fig. 12: Installation with DA = 0 mm
1drawn W = 175 mm
2drawn W = 200 mm
Installation
DA = 0 mm
Fire damper Type FKRS-EU10

Fig. 13: Mount the wall cladding with DA = 0 mm
Note: The cladding of the wall can be done only after the installation of the fire damper.
Fig. 14: Mount the wall cladding and screwing - Single installation kit
Fig. 15: Mount the wall cladding and screwing - Distance between two installation kits ≥ 100 mm
Installation
DA = 0 mm
Fire damper Type FKRS-EU 11

Fig. 16: Mount the wall cladding and screwing - Distance between two installation kits 2 - 5 mm to each other
* optional
Installation
DA = 0 mm
Fire damper Type FKRS-EU12

3.2 DA ≤ 180 mm
Fig. 17: Installation – DA ≤ 180 mm
1pre-drill with 4 mm (Pos. 7), with 3 mm (Pos. 8)
Fig. 18: Installation – DA ≤ 180 mm
1pre-drill with 4 mm (Pos. 7), with 3 mm (Pos. 8)
2drawn W = 175 mm
Installation
DA ≤ 180 mm
Fire damper Type FKRS-EU 13

Fig. 19: Installation – DA ≤ 180 mm
1pre-drill with 4 mm (Pos. 7), with 3 mm (Pos. 8)
3drawn W = 200 mm
Fig. 20: Fixing the brackets to the installation kit GL
1pre-drill with 3 mm
Installation
DA ≤ 180 mm
Fire damper Type FKRS-EU14

Fig. 21: Fixing the fire-rated plasterboard to the installation kit GL
1drawn W = 175 mm
2drawn W = 200 mm
Installation
DA ≤ 180 mm
Fire damper Type FKRS-EU 15

Fig. 22: Create an appropriate opening with DA> 0 ... 180 mm
* at a = 40 mm (drawn)
** closed side for installation opening
Installation
DA ≤ 180 mm
Fire damper Type FKRS-EU16

Fig. 23: Installation with DA ≤ 180 mm
Installation
DA ≤ 180 mm
Fire damper Type FKRS-EU 17

Fig. 24: Installation with DA ≤ 180 mm
1drawn W = 175 mm
2drawn W = 200 mm
Installation
DA ≤ 180 mm
Fire damper Type FKRS-EU18

Fig. 25: Mount the wall cladding with DA ≤ 180 mm
Note: The cladding of the wall can be done only after the installation of the fire damper.
Fig. 26: Mount the wall cladding and screwing - Single installation kit
Fig. 27: Mount the wall cladding and screwing - Distance between two installation kits ≥ 100 mm
Installation
DA ≤ 180 mm
Fire damper Type FKRS-EU 19

Fig. 28: Mount the wall cladding and screwing - Distance between two installation kits 2 - 5 mm to each other
* optional
Installation
DA ≤ 180 mm
Fire damper Type FKRS-EU20