TurnOnGreen EVP1900 User manual

Classic Edition
EVP1900 - User Manual
COPYRIGHT © 2022 reserves the right to make changes to this product without further notice.
Outdoors
version. W84A99900280-HB1
High-End Edition
NEMA 4R Authorization ManagementRepairable
Push Start
Push Start

CONTENT
1. Important Safety Instructions..................................................................1
2. Federal Communication Commission Interference Statement........... 3
3. Industry Canada statement: ....................................................................5
4. Interface.....................................................................................................7
4.1 High-End Edition.................................................................................7
4.2 Classic Edition ....................................................................................8
4.3 Bottom Case and Wire box.................................................................9
5. Dimensions (unit:mm)............................................................................10
6. Specification ........................................................................................... 11
7. Status Description of the Charger Indication Lights .......................... 12
8. Screen Instructions................................................................................13
9. Installation Instructions.........................................................................15
9.1 Contractor Safety guide .................................................................... 15
9.2 Safety Requirements ........................................................................20
9.3 Power Grid Connection and Grounding Type ................................... 21
9.4 Packing List ......................................................................................23
9.5 Tools and Materials Required ........................................................... 24
9.6 Wall-Mount Bracket Installation Requirements ................................. 24
9.7 AX Installation Requirements............................................................25
9.8 Installation Steps ..............................................................................25
10. Charger Standard Setting....................................................................35
10.1 Time Setting ...................................................................................35
10.2 Wi-Fi Setup ..................................................................................... 37
10.3 4G Setup (for the optional 4G Edition)............................................38
10.4 Re-checking the Wi-Fi and 4G Signal Strength on Power-Up ....... 39
11. Local Load Balance Mode .....................................................................41
11.1 Introduction .................................................................................... 41
11.2 Local load balancing setup instructions ......................................... 42
11.3.Local Area Network.........................................................................44
12. Operating Instructions.........................................................................50
12.1 Error and Warning Message ........................................................... 52
13. Maintenance and Repair ......................................................................54
13.1 Daily Maintenance ..........................................................................54
13.2 Maintenance Spares.......................................................................54
13.3 Warranty and Maintenance.............................................................55
13.4 Maintenance History ....................................................................... 59

1. Important Safety Instructions
Please read all Important Safety Instructions as well as charging instructions
in your vehicle owner’s manual before attempting to charge your electric
vehicle. Failure to do so can result in death or severe injury. Save this user
manual for future reference. There are many safety features built into the
charger. Read all the safety information and warnings in this manual to avoid
any risks or hazards and risks associated with using this charger.
Warning
When using electric products, basic precautions should always be followed.
This manual contains important instructions, including the following, which
must be followed during installation, operation and maintenance.
•Do not install or use the charger near flammable, explosive, corrosive, or
combustible materials, chemicals, or vapors.
•Turn off the input power of the charger before performing any
maintenance on the charger.
•The device is designed only for vehicles that are compatible with the SAE
J1772 Level 2 charging standard.
•Do not use the charger if it is defective, of if it appears cracked, frayed,
broken, or damaged.
•Do not attempt to open, disassemble, repair, tamper with, or modify
the charger. Contact our Customer Service department if you have any
questions or require the replacement or repair of any parts.
•Do not use the charger when either you, the vehicle or charger is exposed
to severe rain, snow, or other severe weather.
•When transporting the charger, handle it with care and do not drag or step
on the device.
•Do not touch the charging connector terminal with any sharp metallic
objects, in order to prevent damage.
•Do not forcefully pull the charging cable, damage it with sharp objects,
or place fingers or insert foreign objects into any part of the charging
connector.
EVP1900 - User Manual
1

• Risk of explosion. This device has arcing or sparking parts that should
not be exposed to flammable vapors.
• Risk of electric shock. Do not remove the cover or attempt to open the
enclosure of this device. There are no user-serviceable parts inside.
&RQWDFWDTXDOLHGVHUYLFHFRPSDQ\LI\RXUHTXLUHDQ\VHUYLFHUHSDLUV
• To reduce the risk of fire, connect only to a circuit provided with 60
amperes maximum branch circuit overcurrent protection in accordance
with the national Electrical Code, ANSI/NFPA 70, and the Canadian
Electrical Code, Part I, C22.1
• This charger should be installed, adjusted, and serviced by a qualified
electrician or a person familiar with the construction and operation of
this type of charger and the dangers involved. Failure to observe this
precaution could result in damage to the charger, or even severe injury or
death.
• Incorrect installation and testing of the charger could potentially damage
either the vehicle’s battery and the charger. This type is damage is not
covered by our warranty policy.
• Ensure that the charging cable is well-positioned during the charging
process, to avoid the cable getting stepped on, tripped over, or subjected
to damage or stress.
• Do not use this charger with a frayed charging cable having damaged
insulation or any other sign of damage.
• Ensure that the wire type, diameter, current rating, and temperature rating
comply with the local electrical standards and requirements in your local
area.
• Before starting the installation, turn off all power.
• For permanently connected equipment, protective grounding and bonding
WHUPLQDOVHOGZLULQJWHUPLQDOVIRUFRQQHFWLRQRIHTXLSPHQWJURXQGLQJ
conductors are identified by: "G," "GR," "GND," "Ground," "Grounding" or
the ground symbol, either on a wiring diagram provided on the unit, or a
marking on the wiring diagram attached to the unit.
• This device should be supervised when used around children.
• 'RQRWSXWQJHUVLQWRWKHHOHFWULFYHKLFOHFRQQHFWRU
• The device is not to be lifted or carried by either the flexible cord or the EV
cable
2

This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment
2. Federal Communication
Commission Interference
Statement
EVP1900 - User Manual
3

This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
4

3. Industry Canada statement:
This device complies with ISED’s licence-exempt RSSs. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable,
et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with greater than 20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements
ISED établies pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé à plus de 20 cm entre le radiateur et votre corps.
This device is intended only for OEM integrators under the following
conditions: (For module device use)
The antenna must be installed and operated with greater than 20cm between
the antenna and users, and
The transmitter module may not be co-located with any other transmitter or
antenna.
As long as the 2 conditions above are met, further transmitter test will not
be required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les
conditions suivantes: (Pour utilisation de dispositif module)
L'antenne doit être installé et exploité avec plus de 20 cm entre
EVP1900 - User Manual
5

l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur
ou antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais
supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois,
OLQW«JUDWHXU2(0HVWWRXMRXUVUHVSRQVDEOHGHVHVVDLVVXUVRQSURGXLWQDO
pour toutes exigences de conformité supplémentaires requis pour ce module
installé.
IMPORTANT NOTE:
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada
authorization is no longer considered valid and the IC ID can not be used
on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple
pour certaines configurations d'ordinateur portable ou de certaines co-
localisation avec un autre émetteur), l'autorisation du Canada n'est plus
considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit
QDO'DQVFHVFLUFRQVWDQFHVOLQW«JUDWHXU2(0VHUDFKDUJ«GHU««YDOXHUOH
SURGXLWQDO\FRPSULVO«PHWWHXUHWOREWHQWLRQGXQHDXWRULVDWLRQGLVWLQFWH
au Canada.
6

4. Interface
EVP1900 - User Manual
7
4.1 High-End Edition
Push Start
5” LCD Screen
SAE J1772
AC Charging
Connector
Wall-Mount
Bracket with
Power Box
AC Power Inlet
Charging Cable Inlet
LED Light
Indication

8
4.2 Classic Edition
Push Start
SAE J1772
AC Charging
Connector
Wall-Mount
Bracket with
Power Box
AC Power Inlet
Charging Cable Inlet
LED Light
Indication

EVP1900 - User Manual
9
4.3 Bottom Case and Wire box
Ethernet Inlet
Blade Female Connector
Ethernet Inlet Hole
Network and setting Port
Power and Grounding Setting
Blade Male connector
For 4G SIM Card
AC Inlet
AC Inlet Hole

10
5.1 Main Size of Charger
5.2 Wall-Mount Bracket
5. Dimensions (unit:mm)
Push Start
295 158
505
264.7
384.2
42
163.8
197.8
257.8
337.8
369.7
0
05040 50 87

EVP1900 - User Manual
11
6SHFLÀFDWLRQ
Rated Input Voltage 200-240 VAC / Single Phase
Rated Output Current 80A
AC Power Frequency 50/60 Hz
Input Protection UVP, OVP, Surge protection, Ground fault
Output Protection
OCP, Control pilot fault, Residual current
protection
Output Interface SAE J1772 AC Charging Connector
Storage Temperature -40°C to + 70°C
Operation Temperature -30°C to +50°C
Relative Operation Humidity Up to 85% at 50°C non-condensing
Relative Storage Humidity Up to 95% at 50°C non-condensing
Display LED pilot lamp (standard),
5-inch LCD (High-end)
User Authorization RFID (ISO/IEC 14443A/B, ISO/IEC 15693, FeliCa™,
Mifare), ISO15118
RJ45 Cable Inlet*1 10M/100M Base-T
Wi-Fi Function*1 802.11 b/g/n
2G/3G/4G Finction*1 LTE, UMTS/HSPA(+), GSM/GPRS/EDGE
Cable Length 5M/7.5M (From charger’s body to lower edge of
charging connector)
Protection Level NEMA TYPE 4
Installation Type Wall-Mount
Altitude P
Weight 9±0.5kg/11±0.5kg
Dimensions 295 (W) x 158 (D) x 505 (H) mm
*1 4G Version

12
7. Status Description of the
Charger Indication Lights
Work status Blue Green Red
Initial Constantly Bright
(White)
Idle Backend
connected Sleep -Breath-
Idle
Backend connected -Constantly Bright -
Idle Backend
disconnected Sleep -Breathing (Yellow)
Idle
Backend disconnected -Constantly Bright (Yellow)
Authorize RFID
authorization Pass
Flicker
3 sec
Authorize RFID
authorization Fail
Flicker
3 sec
Handshaking Constantly Bright - -
Charging Flicker - -
Terminate Constantly Bright - -
Complete Constantly Bright - -
MMaintenance
Upgrade -Flicker
(Yellow)
Reservation - Flicker

8. Screen Instructions
8.1 Status bar
8.2 Status Code Table
*For latest status code, please visit our website.
Status Code Description
011004 RCD/CCID self-test fail
011009 output relay welding
011010 output relay driving fault
011021 Wi-Fi module broken
011036 Rotary switch fault
012200 System input OVP
012203 System input UVP
012212 System input drop
012216 System output OCP
012223 System ambient/inlet OTP
012233 RCD/CCID trip
Status Code
4G connected
with internet
4G Not Connected
Wi-Fi connected
with internet
Wi-Fi Not Connected
Ethernet connected
with internet
Ethernet Not Con-
nected
Backend Online %DFNHQG2ႉLQH
Wi-Fi connected
without internet
4G connected
without internet
Ethernet connected
without internet
EVP1900 - User Manual
13

012241 Wi-Fi module communication fail
012242 3G/4G module communication fail
012243 RFID module communication fail
012254 Fail to create share memory
012255 CSU initialization failed
012256 Ground Fault
012257 MCU self-test Fault
012262 Syetem output Circuit Short
012344 Meter IC communication timeout
012345 Pilot negative error
013607 &68PUZDUHXSGDWHIDLO
013622 Disconnected from Internet through Ethernet
013623 Disconnected from Internet through WiFi
013625 Disconnected from AP through WiFi
023703 Pilot fault
14

EVP1900 - User Manual
15
9. Installation Instructions
9.1 Contractor Safety guide
Introduction
•A safe work environment for everyone - participants, installation and
demolition crews, contractors and subcontractors.
•Ultimately, it is the responsibility of contractors to ensure the safety and
safe work practices of their employees and subcontractors who may be
working at the site on their behalf.
•This guide provides a simple reference guide with basic rules for
implementation. This guide does not outline every single safety standard:
it is designed to be a supplement to participants, contractors and
subcontractors.
•Contractors, subcontractors and employees should cooperate with their
employers and other persons in complying with safety regulations and
instructions.
•In particular, employees should:
1. Obtain the qualified authorization of the responsible unit in the
FRQVWUXFWLRQDUHDb
2. Work safely
3. Not do anything to endanger themselves or other persons
4. Use personal protective equipment as required and take reasonable
care of it when it is not in use
5. Report unsafe activities immediately to supervisors or the responsible
person in control of the workplace, and
6. Report all accidents and dangerous occurrences to the supervisor
immediately after they happen

16
• Set up suitable fencing to isolate the construction
area from outside
• Close and secure all entrances when the site is
unattended
• Hang warning notices nearby which show the
following information: warning icon and phone
number of person in charge
• ,QVWDOOVXIFLHQWOLJKWLQJ[WXUHV
• Keep work areas (including accessways) free from
debris and obstructions
• Keep ground surfaces tidy and flat, to avoid people
tripping or being hurt by tools or other objects
• Stack and store equipment and materials in a tidy
and stable manner
• Regularly clean up and dispose of waste
• Remove all surplus materials and equipment after
completion of work
• Beware of flammable materials and goods. Keep
them away from work areas.
1.Requirements for workplace conditions
2.Cleaning up
3.Fire hazards

EVP1900 - User Manual
17
•Erect a sunshade or shed to shelter workers from
the heat and sun
•Set up cooling equipment, such as exhaust fans
•Make water dispensers available
•Provide suitable protective clothing such as hat,
sunglasses and long sleeves to protect workers
from heat stroke and UV rays
•Secure all scaffoldings, temporary structures,
equipment, and loose materials
•Check and implement SOP to ensure
disconnection of gas supplies, electrical circuits
and equipment
•Inspect worksites to ensure protection against
ingress of water or dust
•Inspect the drainage system for blockages and
remove if found
•Stop all outdoor works except for emergency
works
4.Protection against high temperatures on the worksite
5.Inclement weather
•Only use ladders that meet local safety
regulations
•Do not use wooden ladders
•When working at height, it is recommended to use
platforms instead of ladders
•If using a platform is not practicable, a supervisor
should assess the potential risk and provide
safety
6.Ladders